- 您现在的位置：买卖IC网 > PDF目录18656 > ISL29002IROZ-T7 (Intersil)IC SENSOR LIGHT-DGTL I2C 8-ODFN PDF资料下载
参数资料
| 型号： | ISL29002IROZ-T7 |
| 厂商： | Intersil |
| 文件页数： | 8/10页 |
| 文件大小： | 0K |
| 描述： | IC SENSOR LIGHT-DGTL I2C 8-ODFN |
| 产品培训模块： | Ambient Light Sensors |
| 标准包装： | 1 |
| 带接近传感器： | 无 |
| 波长： | 550nm |
| 电源电压： | 2.5 V ~ 3.3 V |
| 输出类型： | I²C? |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-WFDFN 裸露焊盘 |
| 包装： | 标准包装 |
| 产品目录页面： | 1246 (CN2011-ZH PDF) |
| 其它名称： | ISL29002IROZ-T7DKR |
ISL29002
integration is no longer fixed at 32,768, but varies with the
chosen integration time, and is limited to 65,536. In order to
avoid erroneous lux readings the integration must be short
enough not to allow an overflow in the counter register.
adjusted to coincide with an integer multiple of the AC noise
cycle times.
n/m = 60Hz/50Hz = 6/5. The first instance of integer values at
which T int rejects both 60Hz and 50Hz is when m = 5, and n =
T int < ------------------
65,536
f OSC
where:
(EQ. 5)
6.
T int = 6(1/60Hz) = 5(1/50Hz) = 100ms
From Equation 3:
T int = user defined integration time
f osc = 300kHz*100k Ω /R EXT . ISL29002’s internal oscillator.
Not to be confused with the I 2 C’s frequency.
R EXT = user defined external resistor to adjust f osc . 100k Ω
recommended.
The number of clock cycles in the previous integration period
is provided in the third and fourth bytes of data read across
the I 2 C bus. This two-byte value is called the integration
counter value.
When using one of the three external timing modes, the
ISL29002’s resolution varies with the integration time. The
resolution is determined by the ratio of the max lux range to
the number of clock cycles per integration.
The following equations describe the light intensity as a
function of sensor reading, integration counter value, and
integration time:
R EXT = T int * (100k Ω /110ms) = 90.9k Ω . By populating
R EXT = 90k Ω , the ISL29002 defaults to 100ms integration time
and will reject the presence of both 60Hz and 50Hz power line
signals.
Solution 2 - Using External Timing
From solution 1, the desired integration time is 100ms. Note
that the R EXT resistor does not determine the integration time
when using external timing mode. Instead, the integration and
the 16-bit counter starts when an external timing mode
command is sent and end when another external timing mode
is sent. In other words, the time between two external timing
mode command is the integration time. The programmer
determines how many clock cycles to wait between two
external timing commands.
i I2C = f I2C * T int , where i I2C = number of I 2 C cycles
i I2C = 10kHz * 100ms
E ( lux ) = ------------------------------------------- ? -----------------
50 , 000lux Data1
( R EXT ? 100k Ω ) Data2
(EQ. 6)
i I2C = 1,000 I 2 C clock cycles. An external timing command
1,000 cycles after another external timing command rejects
T int = Time Interval between external time commands
where L is the measured light intensity, Data1 is the sensor
reading, Data2 is the integration counter value, T is the
integration time, and R EXT is external resistor value.
Noise Rejection and Integration Time
In general, integrating type ADC’s have an excellent noise-
rejection characteristics for periodic noise sources whose
frequency is an integer multiple of the integration time. For
instance, a 60Hz AC unwanted signal’s sum from 0ms to
n*16.66ms (n = 1,2...n i ) is zero. Similarly, setting the
ISL29002’s integration time to an integer multiple of periodic
noise signal greatly improves the light sensor output signal
in the presence of noise. The integration time, T int , of the
both 60Hz and 50Hz AC noise signals.
IR Rejection
Any filament type light source has a high presence of infrared
component invisible to the human eye. A white fluorescent
lamp, on the other hand has a low IR content. As a result,
output sensitivity may vary depending on the light source.
Maximum attenuation of IR can be achieved by properly scaling
the readings of Diode1 and Diode2. The user obtains data
reading from sensor diode 1, D1, which is sensitive to visible
and IR, then reading from sensor diode 2, D2 which is mostly
sensitive from IR. The graph on Figure 9 shows the effective
spectral response after applying Equation 7 of the ISL29002
from 400nm to 1000nm. The equation below describes the
method of cancelling IR in internal timing mode.
ISL29002 is set by an external resistor R EXT .
See Equation 3.
D3 = n ( D1 – kD2 )
(EQ. 7)
Design Example 1
Using the ISL29002, determine a suitable integration time,
T int , that will ignore the presence of both 60Hz and 50Hz
noise. Accordingly, specify the R EXT value. Given that the
I 2 C clock is at f I2C = 10kHz.
Solution 1 - Using Internal Timing
T int = n(1/60Hz) = m(1/50Hz). In order to achieve both 60Hz
and 50Hz AC rejection, the integration time needs to be
8
Where:
data = lux amount in number of counts less IR presence
D1 = data reading of Diode 1
D2 = data reading of Diode 2
n = 1.85. This is a fudge factor to scale back the sensitivity up to
ensure Equation 2 is valid.
k = 7.5. This is a scaling factor for the IR sensitive Diode 2.
FN7465.2
December 1, 2006
相关PDF资料 |
PDF描述 |
|---|---|
| 563P3P36 | CABLE STR MALE-MALE 3POS 3' |
| XREWHT-L1-0000-005F5 | LED NEUTRAL WHITE 7X9MM SMD |
| XMLHVW-Q2-0000-0000LT253 | LED XM-L HIGH VOLTAGE WHITE |
| 192P2S72 | CABLE 2POS MALE-FEMALE STR 6' |
| XMLHVW-Q2-0000-0000HS3F8 | LED XM-L HIGH VOLTAGE WHITE |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL29003IROZ | 功能描述:IC SENSOR LIGHT-DGTL I2C 6-ODFN RoHS:是 类别:传感器，转换器 >> 光学 - 光电探测器 - 环境光传感器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 产品变化通告:Product Discontinuation 25/Jun/2012 标准包装:2,500 系列:- 带接近传感器:无 波长:- 电源电压:1.7 V ~ 2 V 电流 - 暗（标准）:- 电流 - 光（典型值）:- 输出类型:数字 - I²C 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:6-UDFN 裸露焊盘 包装:带卷 (TR) |
| ISL29003IROZ-EVALZ | 功能描述:EVALUATION BOARD FOR ISL29003 RoHS:是 类别:编程器，开发系统 >> 评估板 - 传感器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1 系列:- |
| ISL29003IROZ-T7 | 功能描述:光学数位转换器 ISL29003IROZ LIGHT-T O-DIGTL I2C GAIN RoHS:否 制造商:ams 数据总线宽度: 峰值波长:470 nm 最大工作频率: 工作电源电压: 工作电流: 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:Chipscale-6 封装:Reel |
| ISL29004IROZ | 功能描述:IC SENSOR LIGHT-DGTL I2C 8-ODFN RoHS:是 类别:传感器，转换器 >> 光学 - 光电探测器 - 环境光传感器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 产品变化通告:Product Discontinuation 25/Jun/2012 标准包装:2,500 系列:- 带接近传感器:无 波长:- 电源电压:1.7 V ~ 2 V 电流 - 暗（标准）:- 电流 - 光（典型值）:- 输出类型:数字 - I²C 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:6-UDFN 裸露焊盘 包装:带卷 (TR) |
| ISL29004IROZ-EVALZ | 制造商:Intersil Corporation 功能描述:INTRFC LIGHT-TO-DGTL OUTPUT SENSOR - Bulk |
发布紧急采购，3分钟左右您将得到回复。