- 您现在的位置：买卖IC网 > PDF目录17112 > ISL29006IROZ-EVALZ (Intersil)EVALUATION BOARD FOR ISL29006 PDF资料下载
参数资料
| 型号： | ISL29006IROZ-EVALZ |
| 厂商： | Intersil |
| 文件页数： | 8/11页 |
| 文件大小： | 0K |
| 描述： | EVALUATION BOARD FOR ISL29006 |
| 标准包装： | 1 |
| 传感器类型： | 灯光，电流输出 |
| 传感范围： | 10000Lux |
| 接口： | 模拟 |
| 灵敏度： | 550nm |
| 电源电压： | 1.8 V ~ 3.3 V |
| 嵌入式： | 否 |
| 已供物品： | 板 |
| 已用 IC / 零件： | ISL29006 |
ISL29006, ISL29007, ISL29008
I OUT = ? ------------------- ? × E
1.6 μ A
? 100lux ?
Application Information
Light-to-Current and Voltage Conversion
The ISL29006, ISL29007 and ISL29008 have
responsiveness that is directly proportional to the intensity of
light intercepted by the photodiode arrays. Conversion rate
is independent of the light sources (fluorescent light,
incandescent light or direct sunlight).
(EQ. 1)
Here, I OUT is the output current in μA, and E is the input light
response of the ambient light detector for a given exposure
of light.
The example in Figure 20 shows a fully automatic dimming
solution with no user interaction. Choose R 1 and R 2 values
for any desired minimum brightness and slope. Choose C 1
to adjust response time and to filter 50/60Hz room lighting.
For example, suppose you wish to generate an output
voltage from 0.25V to 1.2V to drive the input of an LED driver
controller. The 0.25V represents the minimum LED
brightness and 1.2V represents the maximum. The 1st step
would be to determine the ratio of R 1 and R 2 in Equation 4:
R 1 = R 2 × ? ---------------- – 1 ? = 11 × R 2
V OUT = I OUT × R L = ? ------------------- ? × E × R L
in lux.
For some applications, a load resistor is added between the
output and the ground, as shown in Figure 1. The output
voltage can be expressed in Equation 2:
1.6 μ A
(EQ. 2)
? 100lux ?
Here, V OUT is the output voltage and R L is the value of the
3.0V
? 0.25V ?
3V TO 5V
SUPPLY VOLTAGE
VDD
3V DC VOLTAGE
R1
660k
(EQ. 4)
external load resistor. The compliance of the ISL29006's
output circuit may result in premature saturation of the
output current and voltage when an excessively large R L is
ISL29006
ISRC
TO INVERTER BRIGHTNESS
INPUT OR LED DRIVER
CONTROLLER
used. The output compliance voltage is 300mV below the
supply voltage as listed in V O-MAX of the “Electrical
GND
R2
60k
C1
25μF
Specifications” table on page 3.
In order to have the linear relationship between the input
light and the output current and voltage, a proper resistor
value (i.e., gain) should be picked for a specific input light
range. The resistor value can be picked according to
Equation 3:
FIGURE 20.
Next, the value of R 2 can be calculated based on the
maximum output current coming from the ISL29006 under
( V SUP – 0.3V ) 100lux
R L = --------------------------------------- × ------------------------
E RANGE
(EQ. 3)
the application's maximum light exposure. Suppose the
current has been determined to be about 2μA. Thus, R 2 can
be approximately calculated using Equations 5 and 6:
R 2 = ? ------------ ? = 60k Ω
Here, V SUP is the supply voltage and E RANGE is the specific
input light range for an application. For example, an indoor
light ranges typically from 0 lux to 1,000 lux. A resistor value
of 270k Ω for 3V supply voltage can be used. For a small light
range, a large resistor value should be used to achieve
better sensitivity; for a large light range, a small resistor
1.2V
? 2 μ A ?
and Equation 6:
R 1 = 11 × R 2 = 660k Ω
(EQ. 5)
(EQ. 6)
value should be used to prevent non-linear output current
and voltage.
Application Examples
The following examples present from fully automatic to fully
manual override implementations. These guidelines are
applicable to a wide variety of potential light control
applications. The ISL29006, ISL29007 and ISL29008 can be
used to control the brightness input of CCFL inverters.
Likewise, it can interface well with LED drivers. In each
specific application, it is important to recognize the target
environment and its ambient light conditions. The
mechanical mounting of the sensor, light aperture hole size
and use of a light pipe or bezel are critical in determining the
8
In Figure 20, the 3VDC supply can be replaced with a user
adjustable bias control, such as 3V PWM control to allow
control over the minimum and maximum output voltage.
Figure 21 shows that ISL29006 is used to provide automatic
dimming control.
Short Circuit Current Limit
The ISL29006, ISL29007 and ISL29008 do not limit the
output short circuit current. If the output is directly shorted to
the ground continuously, the output current could easily
increase for a strong input light such that the device may be
damaged. Maximum reliability is maintained if the output
continuous current never exceeds 6mA by adding a load
FN6282.1
September 21, 2010
相关PDF资料 |
PDF描述 |
|---|---|
| VE-J4J-EZ | CONVERTER MOD DC/DC 36V 25W |
| VE-JV0-EZ | CONVERTER MOD DC/DC 5V 25W |
| VI-J4L-EZ | CONVERTER MOD DC/DC 28V 25W |
| VI-J4K-EZ | CONVERTER MOD DC/DC 40V 25W |
| 60B224C | IND 220UH 5.0A POWER CORE SMD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL29006IROZ-T7 | 功能描述:IC PHOTO DETECTOR AMBIENT 6-ODFN RoHS:是 类别:传感器，转换器 >> 光学 - 光电探测器 - 环境光传感器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 产品变化通告:Product Discontinuation 25/Jun/2012 标准包装:2,500 系列:- 带接近传感器:无 波长:- 电源电压:1.7 V ~ 2 V 电流 - 暗（标准）:- 电流 - 光（典型值）:- 输出类型:数字 - I²C 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:6-UDFN 裸露焊盘 包装:带卷 (TR) |
| ISL29007IROZ-EVALZ | 功能描述:EVALUATION BOARD FOR ISL29007 RoHS:是 类别:编程器，开发系统 >> 评估板 - 传感器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1 系列:- |
| ISL29007IROZ-T7 | 功能描述:IC PHOTO DETECTOR AMBIENT 6-ODFN RoHS:是 类别:传感器，转换器 >> 光学 - 光电探测器 - 环境光传感器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 产品变化通告:Product Discontinuation 25/Jun/2012 标准包装:2,500 系列:- 带接近传感器:无 波长:- 电源电压:1.7 V ~ 2 V 电流 - 暗（标准）:- 电流 - 光（典型值）:- 输出类型:数字 - I²C 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:6-UDFN 裸露焊盘 包装:带卷 (TR) |
| ISL29008IROZ-EVALZ | 功能描述:EVALUATION BOARD FOR ISL29008 RoHS:是 类别:编程器，开发系统 >> 评估板 - 传感器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1 系列:- |
| ISL29008IROZ-T7 | 功能描述:IC PHOTO DETECTOR AMBIENT 6-ODFN RoHS:是 类别:传感器，转换器 >> 光学 - 光电探测器 - 环境光传感器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 产品变化通告:Product Discontinuation 25/Jun/2012 标准包装:2,500 系列:- 带接近传感器:无 波长:- 电源电压:1.7 V ~ 2 V 电流 - 暗（标准）:- 电流 - 光（典型值）:- 输出类型:数字 - I²C 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:6-UDFN 裸露焊盘 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。