- 您现在的位置：买卖IC网 > PDF目录10675 > ISL3158AEMBZ-T7A (Intersil)IC LINEAR PDF资料下载
参数资料
| 型号： | ISL3158AEMBZ-T7A |
| 厂商： | Intersil |
| 文件页数： | 14/16页 |
| 文件大小： | 0K |
| 描述： | IC LINEAR |
| 标准包装： | 1 |
| 系列： | * |
| 其它名称： | ISL3158AEMBZ-T7ADKR |
7
FN6886.1
October 15, 2013
Receiver Enable to Output High
tZH
(Note 9)
Full
-
7
15
ns
Receiver Disable from Output Low
tLZ
Full
-
8
15
ns
Receiver Disable from Output High
tHZ
Full
-
8
15
ns
Time to Shutdown
tSHDN
(Notes 10, 15)
Full
60
160
600
ns
Receiver Enable from Shutdown to
Output High
(Notes 10, 12)
Full
-
200
ns
Receiver Enable from Shutdown to
Output Low
(Notes 10, 12)
Full
-
200
ns
NOTES:
5. All currents into device pins are positive; all currents out of device pins are negative. All voltages are referenced to device ground unless
otherwise specified.
6. Supply current specification is valid for loaded drivers when DE = 0V.
7. Applies to peak current. See “Typical Performance Curves” beginning on page 12 for more information.
8. Keep RE = 0 to prevent the device from entering SHDN.
9. The RE signal high time must be short enough (typically <100ns) to prevent the device from entering SHDN.
10. Transceivers are put into shutdown by bringing RE high and DE low. If the inputs are in this state for less than 60ns, the parts are guaranteed
not to enter shutdown. If the inputs are in this state for at least 600ns, the parts are guaranteed to have entered shutdown. See “Low Power
11. Keep RE = VCC, and set the DE signal low time >600ns to ensure that the device enters SHDN.
12. Set the RE signal high time >600ns to ensure that the device enters SHDN.
13. See Figure 8 for more information, and for performance over-temperature.
14. For wafer sale, the switching test limits are established by characterization.
15. Limits established by characterization and are not production tested.
Test Circuits and Waveforms
FIGURE 1A. VOD AND VOC
FIGURE 1B. VOD WITH COMMON MODE LOAD
FIGURE 1. DC DRIVER TEST CIRCUITS
Electrical Specifications
Test Conditions: VCC = 4.5V to 5.5V; Unless Otherwise Specified. Typicals are at VCC = 5V, TA = +25°C
(Note 5). Parameters with MIN and/or MAX limits are 100% tested at +25°C, unless otherwise specified.
Temperature limits established by characterization and are not production tested.
(Continued)
PARAMETER
SYMBOL
TEST CONDITIONS
TEMP
(°C)
MIN
TYP
MAX
UNITS
D
DE
DI
VCC
VOD
VOC
RL/2
Z
Y
D
DE
DI
VCC
VOD
375
Ω
375
Ω
Z
Y
RL = 60Ω
VCM
-7V TO +12V
ISL3158AE
相关PDF资料 |
PDF描述 |
|---|---|
| VI-JWK-MY-F3 | CONVERTER MOD DC/DC 40V 50W |
| ALD2321BPCL | IC COMP VOLT PUSH-PULL DL 16PDIP |
| VI-B1X-MX-F1 | CONVERTER MOD DC/DC 5.2V 75W |
| VI-JWK-MY-F2 | CONVERTER MOD DC/DC 40V 50W |
| VI-B1W-MX-F4 | CONVERTER MOD DC/DC 5.5V 75W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL3158AEMW | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:±16.5kV ESD (IEC61000-4-2) Protected, Large Output Swing, 5V, Full Fail-Safe, 1/8 Unit Load, RS-485/RS-422 Transceiver |
| ISL3158E | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:±16.5kV ESD, Large Output Swing, 5V, Full Fail-Safe, 1/8 Unit Load, RS-485/RS-422 Transceivers |
| ISL3158EIBZ | 功能描述:RS-422/RS-485 接口 IC 8LD IEC6100 3V HI VOD TRANS 1 RoHS:否 制造商:Maxim Integrated 数据速率:1136 Kbps 工作电源电压:3 V to 5.5 V 电源电流:5.9 mA 工作温度范围:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-28 封装:Tube |
| ISL3158EIBZ-T | 功能描述:TXRX ESD 5V RS-485/422 8-SOIC RoHS:是 类别:集成电路 (IC) >> 接口 - 驱动器，接收器，收发器 系列:- 标准包装:250 系列:- 类型:收发器 驱动器/接收器数:2/2 规程:RS232 电源电压:3 V ~ 5.5 V 安装类型:表面贴装 封装/外壳:16-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:16-TSSOP 包装:带卷 (TR) |
| ISL3158EIBZ-T7A | 功能描述:RS-422/RS-485 接口 IC 8LD -40+85 3V RS-485 HIVOD TRAN 1/ RoHS:否 制造商:Maxim Integrated 数据速率:1136 Kbps 工作电源电压:3 V to 5.5 V 电源电流:5.9 mA 工作温度范围:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-28 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。