参数资料
| 型号： | ISL3241EIRZ |
| 厂商： | Intersil |
| 文件页数： | 5/16页 |
| 文件大小： | 0K |
| 描述： | IC TXRX RS232 ESD-PROT 32-QFN |
| 产品培训模块： | Solutions for Industrial Control Applications |
| 标准包装： | 60 |
| 类型： | 收发器 |
| 驱动器/接收器数： | 3/5 |
| 规程： | RS232 |
| 电源电压： | 2.7 V ~ 3.6 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 32-VFQFN 裸露焊盘 |
| 供应商设备封装： | 32-QFN 裸露焊盘（5x5） |
| 包装： | 管件 |
ISL3241E, ISL3243E
13
FN6768.2
June 18, 2012
Interconnection to 1.8V, and
2.5V Logic
Standard 3.3V powered RS-232 devices interface well with 3V
powered TTL compatible logic families (e.g., ACT and HCT).
The ISL324xE VL supply pin allows interconnection to 1.8V or
2.5V logic. By connecting VL to the same supply (1.8V or 2.5V)
powering the logic device, the ISL324XE logic outputs will
swing from GND to the logic VCC.
±15kV ESD Protection
All pins on ISL324xE devices include ESD protection structures,
but the RS-232 pins (transmitter outputs and receiver inputs)
incorporate advanced structures which allow them to survive
ESD events up to ±15kV. The RS-232 pins are particularly
vulnerable to ESD damage because they typically connect to
an exposed port on the exterior of the finished product. Simply
touching the port pins, or connecting a cable, can cause an
ESD event that might destroy unprotected ICs. These new ESD
structures protect the device whether or not it is powered up,
protect without allowing any latchup mechanism to activate,
and don’t interfere with RS-232 signals as large as ±25V.
Human Body Model (HBM) Testing
As the name implies, this test method emulates the ESD event
delivered to an IC during human handling. The tester delivers
the charge through a 1.5k current limiting resistor, making
the test less severe than the IEC61000 test which utilizes a
330 limiting resistor. The HBM method determines an ICs
ability to withstand the ESD transients typically present during
handling and manufacturing. Due to the random nature of
these events, each pin is tested with respect to all other pins.
The RS-232 pins on “E” family devices can withstand HBM ESD
events to ±15kV.
IEC61000-4-2 Testing
The IEC61000 test method applies to finished equipment,
rather than to an individual IC. Therefore, the pins most likely
to suffer an ESD event are those that are exposed to the
outside world (the RS-232 pins in this case), and the IC is
tested in its typical application configuration (power applied)
rather than testing each pin-to-pin combination. The lower
current limiting resistor coupled with the larger charge storage
capacitor yields a test that is much more severe than the HBM
test. The extra ESD protection built into this device’s RS-232
pins allows the design of equipment meeting level 4 criteria
without the need for additional board level protection on the
RS-232 port.
AIR-GAP DISCHARGE TEST METHOD
For this test method, a charged probe tip moves toward the IC
pin until the voltage arcs to it. The current waveform delivered
to the IC pin depends on approach speed, humidity,
temperature, etc., so it is difficult to obtain repeatable results.
The “E” device RS-232 pins withstand ±15kV air-gap
discharges.
CONTACT DISCHARGE TEST METHOD
During the contact discharge test, the probe contacts the
tested pin before the probe tip is energized, thereby
eliminating the variables associated with the air-gap
discharge. The result is a more repeatable and predictable
test, but equipment limits prevent testing devices at voltages
higher than ±8kV. All “E” family devices survive ±8kV contact
discharges on the RS-232 pins.
FIGURE 15. LOOPBACK TEST AT 250kbps
T1IN
T1OUT
R1OUT
2s/DIV.
VCC = +3.3V, VL = 1.8V
C1 TO C4 = 0.1F
3V/DIV.
5V/DIV.
3V/DIV.
相关PDF资料 |
PDF描述 |
|---|---|
| ICL3241IBZ | IC 3DRVR/5RCVR RS232 3V 28-SOIC |
| ISL83385EIBZ | IC 2DRVR/2RCVR RS232 18-SOIC |
| MS27656T11F5SA | CONN RCPT 5POS WALL MNT W/SCKT |
| IDT723676L15PF | IC FIFO SYNC 16384X36 128QFP |
| MS27466T11B4PB | CONN RCPT 4POS WALL MT W/PINS |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL3241EIRZ-T | 功能描述:IC TXRX RS232 ESD-PROT 32-QFN RoHS:是 类别:集成电路 (IC) >> 接口 - 驱动器，接收器，收发器 系列:- 标准包装:250 系列:- 类型:收发器 驱动器/接收器数:2/2 规程:RS232 电源电压:3 V ~ 5.5 V 安装类型:表面贴装 封装/外壳:16-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:16-TSSOP 包装:带卷 (TR) |
| ISL32430E | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:?±40V Fault Protected, 3.3V to 5V, ?±15V Common Mode Range, RS-485/RS-422 Transceivers With Cable Invert and ?±15kV ESD |
| ISL32430EIBZ | 功能描述:IC TRANSCEIVER 14-SOIC RoHS:是 类别:集成电路 (IC) >> 接口 - 驱动器，接收器，收发器 系列:* 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 类型:发射器 驱动器/接收器数:4/0 规程:RS422，RS485 电源电压:4.75 V ~ 5.25 V 安装类型:表面贴装 封装/外壳:16-SOIC（0.154"，3.90mm 宽） 供应商设备封装:16-SOIC 包装:带卷 (TR) |
| ISL32430EIBZ-T | 功能描述:IC TRANSCEIVER 14-SOIC RoHS:是 类别:集成电路 (IC) >> 接口 - 驱动器，接收器，收发器 系列:* 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 类型:发射器 驱动器/接收器数:4/0 规程:RS422，RS485 电源电压:4.75 V ~ 5.25 V 安装类型:表面贴装 封装/外壳:16-SOIC（0.154"，3.90mm 宽） 供应商设备封装:16-SOIC 包装:带卷 (TR) |
| ISL32430EIBZ-T7A | 功能描述:RS-422/RS-485 接口 IC 40V OVP 15V CMR -40+ 85 3V RS-485 FL DUP RoHS:否 制造商:Maxim Integrated 数据速率:1136 Kbps 工作电源电压:3 V to 5.5 V 电源电流:5.9 mA 工作温度范围:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-28 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。