参数资料
| 型号： | ISL32475EIBZ-T7A |
| 厂商： | Intersil |
| 文件页数： | 19/19页 |
| 文件大小： | 0K |
| 描述： | IC TXRX RS485 FAULT PROT 8SOIC |
| 产品培训模块： | Solutions for Industrial Control Applications |
| 标准包装： | 250 |
| 类型： | 收发器 |
| 驱动器/接收器数： | 1/1 |
| 规程： | RS422，RS485 |
| 电源电压： | 4.5 V ~ 5.5 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 8-SOIC |
| 包装： | 带卷 (TR) |
ISL32470E, ISL32472E, ISL32475E, ISL32478E
9
FN7784.1
March 16, 2012
Time to Shutdown
tSHDN
(Note 11)
Full
60
160
600
ns
Receiver Enable from Shutdown to
Output High
(Notes 11, 13)
Full
-
2000
ns
Receiver Enable from Shutdown to
Output Low
(Notes 11, 13)
Full
-
2000
ns
NOTES:
6. All currents into device pins are positive; all currents out of device pins are negative. All voltages are referenced to device ground unless otherwise
specified.
7. Supply current specification is valid for loaded drivers when DE = 0V.
8. Applies to peak current. See “Typical Performance Curves” beginning on page 13 for more information.
9. Keep RE = 0 to prevent the device from entering SHDN.
10. The RE signal high time must be short enough (typically <100ns) to prevent the device from entering SHDN.
11. Transceivers are put into shutdown by bringing RE high and DE low. If the inputs are in this state for less than 60ns, the parts are guaranteed not to
enter shutdown. If the inputs are in this state for at least 600ns, the parts are guaranteed to have entered shutdown. See “Low Power Shutdown
12. Keep RE = VCC, and set the DE signal low time >600ns to ensure that the device enters SHDN.
13. Set the RE signal high time >600ns to ensure that the device enters SHDN.
14. Compliance to data sheet limits is assured by one or more methods: production test, characterization and/or design.
15. Tested according to TIA/EIA-485-A, Section 4.2.6 (±80V for 15s at a 1% duty cycle).
16. See “Caution” statement below the “Recommended Operating Conditions” section on page 5.
Test Circuits and Waveforms
FIGURE 3A. VOD AND VOC
FIGURE 3B. VOD AND VOC WITH COMMON MODE LOAD
FIGURE 3. DC DRIVER TEST CIRCUITS
Electrical Specifications Test Conditions: VCC = 4.5V to 5.5V; Unless Otherwise Specified. Typicals are VCC = 5V, TA = +25°C
(Note 6). Boldface limits apply over the operating temperature range, -40°C to +85°C. (Continued)
PARAMETER
SYMBOL
TEST CONDITIONS
TEMP
(°C)
MIN
(Note 14)
TYP
MAX
(Note 14)
UNITS
D
DE
DI
VCC
VOD
VOC
RL/2
Z
Y
D
DE
DI
VCC
VOD
375
Z
Y
VCM
RL/2
VOC
相关PDF资料 |
PDF描述 |
|---|---|
| MAX1149BEUP+T | IC ADC 14BIT 116KSPS 20-TSSOP |
| ISL32472EIBZ-T7A | IC TXRX RS485 FAULT PROT 8SOIC |
| MAX1148BEUP+T | IC ADC 14BIT 116KSPS 20-TSSOP |
| MAX158BCAI+T | IC ADC 8BIT 8CH W/MUX&REF 28SSOP |
| MAX1297AEEG+T | IC ADC 12BIT 265KSPS 24-QSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL32478E | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Fault Protected, Extended Common Mode Range, RS-485/RS-422 Transceivers |
| ISL32478EIBZ | 功能描述:IC TXRX RS485 FAULT PROT 8SOIC RoHS:是 类别:集成电路 (IC) >> 接口 - 驱动器，接收器，收发器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:50 系列:- 类型:收发器 驱动器/接收器数:1/1 规程:RS422，RS485 电源电压:4.75 V ~ 5.25 V 安装类型:通孔 封装/外壳:8-DIP（0.300"，7.62mm） 供应商设备封装:8-PDIP 包装:管件 产品目录页面:1402 (CN2011-ZH PDF) |
| ISL32478EIBZ-T | 功能描述:IC TXRX RS485 FAULT PROT 8SOIC RoHS:是 类别:集成电路 (IC) >> 接口 - 驱动器，接收器，收发器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 类型:发射器 驱动器/接收器数:4/0 规程:RS422，RS485 电源电压:4.75 V ~ 5.25 V 安装类型:表面贴装 封装/外壳:16-SOIC（0.154"，3.90mm 宽） 供应商设备封装:16-SOIC 包装:带卷 (TR) |
| ISL32478EIBZ-T7A | 功能描述:RS-422/RS-485 接口 IC 8LD OVP -40+85 5V RS HD+/-15V CMR 10MBPS RoHS:否 制造商:Maxim Integrated 数据速率:1136 Kbps 工作电源电压:3 V to 5.5 V 电源电流:5.9 mA 工作温度范围:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-28 封装:Tube |
| ISL32483E | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Fault Protected, Extended CMR, RS-485/RS-422 Transceivers |
发布紧急采购，3分钟左右您将得到回复。