参数资料
| 型号： | ISL4241EIR-T |
| 厂商： | Intersil |
| 文件页数： | 12/14页 |
| 文件大小： | 0K |
| 描述： | IC 3DRVR/5RCVR RS232 3V 32-QFN |
| 标准包装： | 6,000 |
| 类型： | 收发器 |
| 驱动器/接收器数： | 3/5 |
| 规程： | RS232 |
| 电源电压： | 2.7 V ~ 5.5 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 32-VFQFN 裸露焊盘 |
| 供应商设备封装： | 32-QFN 裸露焊盘（5x5） |
| 包装： | 带卷 (TR) |
7
FN8037.7
June 10, 2010
Detailed Description
The ISL4241E and ISL4243E both operate from a single
+2.7V to +5.5V supply, guarantee a 250kbps minimum data
rate, require only four small external 0.1F capacitors,
feature low power consumption, and meet all ElA RS-232C
and V.28 specifications even with VCC = 3.0V. The circuit is
divided into three sections: The charge pump, the
transmitters, and the receivers.
Charge-Pump
Intersil’s new ISL4241E, ISL4243E devices utilize regulated
on-chip dual charge pumps as voltage doublers, and voltage
inverters to generate ±5.5V transmitter supplies from a VCC
supply as low as 3.0V. This allows them to maintain RS-232
compliant output levels over the ±10% tolerance range of
3.3V powered systems. The efficient on-chip power supplies
require only four small, external 0.1F capacitors for the
voltage doubler and inverter functions. The charge pumps
operate discontinuously (i.e., they turn off as soon as the V+
and V- supplies are pumped up to the nominal values),
resulting in significant power savings.
Transmitters
The transmitters are proprietary, low dropout, inverting
drivers that translate TTL/CMOS inputs to EIA/TIA-232
output levels. Coupled with the on-chip ±5.5V supplies,
these transmitters deliver true RS-232 levels over a wide
range of single supply system voltages.
All transmitter outputs disable and assume a high
impedance state when the device enters the power-down
mode (see Table 2). These outputs may be driven to ±12V
when disabled.
The devices guarantee a 250kbps data rate for full load
conditions (3k
Ω and 1000pF), VCC ≥ 3.0V, with one
transmitter operating at full speed. Under more typical
conditions of VCC ≥ 3.3V, RL = 3kΩ, and CL = 250pF, one
transmitter easily operates at 900kbps.
Transmitter inputs float if left unconnected, and may cause
ICC increases. Connect unused inputs to GND for the best
performance.
Receivers
All the ISL4241E, ISL4243E’s devices contain standard
inverting receivers that are three-state via the EN or
FORCEOFF control lines. Additionally, the ISL4241E,
ISL4243E’s products include noninverting (monitor)
receivers (denoted by the ROUTB label) that are always
active, regardless of the state of any control lines. All the
receivers convert RS-232 signals to CMOS output levels and
accept inputs up to
±25V while presenting the required 3kΩ
to 7k
Ω input impedance (see Figure 1) even if the power is
off (VCC = 0V). The receivers’ Schmitt trigger input stage
uses hysteresis to increase noise immunity and decrease
errors due to slow input signal transitions.
The ISL4241E inverting receivers disable only when EN is
driven high. ISL4243E receivers disable during forced
(manual) power-down, but not during automatic power-down
(see Table 2).
Transition Region Slew Rate
VCC = 3V to 3.6V, RL = 3kΩ to 7kΩ,
Measured From 3V to -3V or -3V to 3V
CL = 150pF to
2500pF
25
4
9
30
V/s
Full
4
8
30
V/s
CL = 150pF to
1000pF
25
6
11
30
V/s
Full
6
10
30
V/s
ESD PERFORMANCE
RS-232 Pins (TOUT, RIN)
Human Body Model
25
-
±15
-
kV
IEC61000-4-2 Contact Discharge
25
-
±8
-
kV
IEC61000-4-2 Air Gap Discharge
25
-
±15
-
kV
All Other Pins
Human Body Model
25
-
±2
-
kV
NOTE:
3. Transmitter skew is measured at the transmitter zero crossing points.
4. Parameters with MIN and/or MAX limits are 100% tested at +25°C, unless otherwise specified. Temperature limits established by characterization
and are not production tested.
Electrical Specifications
Test Conditions: VCC = 3V to 5.5V, C1 to C4 = 0.1F; Unless Otherwise Specified.
Typicals are at TA = +25°C (Continued)
PARAMETER
TEST CONDITIONS
TEMP
(°C)
MIN
(Note 4)
TYP
MAX
(Note 4) UNITS
RXOUT
GND
≤ VROUT ≤ VCC
5k
Ω
RXIN
-25V
≤ VRIN ≤ +25V
GND
VCC
FIGURE 1.
INVERTING RECEIVER CONNECTIONS
ISL4241E, ISL4243E
相关PDF资料 |
PDF描述 |
|---|---|
| VE-22L-MX-F2 | CONVERTER MOD DC/DC 28V 75W |
| V300B2H100BG | CONVERTER MOD DC/DC 2V 100W |
| M83723/75R1412N | CONN PLUG 12POS STRAIGHT W/SCKT |
| V300B28H250BF | CONVERTER MOD DC/DC 28V 250W |
| M83723/72R1624N | CONN RCPT 24POS WALL MT W/PINS |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL4241EIRZ | 功能描述:IC 3DRVR/5RCVR RS232 3V 32-QFN RoHS:是 类别:集成电路 (IC) >> 接口 - 驱动器，接收器，收发器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 类型:发射器 驱动器/接收器数:4/0 规程:RS422，RS485 电源电压:4.75 V ~ 5.25 V 安装类型:表面贴装 封装/外壳:16-SOIC（0.154"，3.90mm 宽） 供应商设备封装:16-SOIC 包装:带卷 (TR) |
| ISL4241EIRZ-T | 功能描述:IC XMITTER/RCVR ESD RS232 32-QFN RoHS:是 类别:集成电路 (IC) >> 接口 - 驱动器，接收器，收发器 系列:- 标准包装:2,500 系列:- 类型:驱动器 驱动器/接收器数:4/0 规程:RS422 电源电压:4.5 V ~ 5.5 V 安装类型:表面贴装 封装/外壳:16-SOIC（0.154"，3.90mm 宽） 供应商设备封装:16-SOIC N 包装:带卷 (TR) |
| ISL4243E | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:QFN Packaged, ±15kV ESD Protected, +2.7V to +5.5V, 10Nanoamp, 250kbps, +2.7V to +5.5V, 10Nanoamp, 250kbps, |
| ISL4243EIR | 功能描述:RS-232接口集成电路 TXRX 2.7-5.5V ESD RoHS:否 制造商:Exar 数据速率:52 Mbps 工作电源电压:5 V 电源电流:300 mA 工作温度范围:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体:LQFP-100 封装: |
| ISL4243EIR-T | 功能描述:IC 3DRVR/5RCVR RS232 3V 32-QFN RoHS:否 类别:集成电路 (IC) >> 接口 - 驱动器，接收器，收发器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:25 系列:- 类型:收发器 驱动器/接收器数:2/2 规程:RS232 电源电压:4.5 V ~ 5.5 V 安装类型:通孔 封装/外壳:16-DIP（0.300"，7.62mm） 供应商设备封装:16-PDIP 包装:管件 |
发布紧急采购，3分钟左右您将得到回复。