参数资料
| 型号： | ISL4241EIRZ |
| 厂商： | Intersil |
| 文件页数： | 14/14页 |
| 文件大小： | 0K |
| 描述： | IC 3DRVR/5RCVR RS232 3V 32-QFN |
| 标准包装： | 60 |
| 类型： | 收发器 |
| 驱动器/接收器数： | 3/5 |
| 规程： | RS232 |
| 电源电压： | 2.7 V ~ 5.5 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 32-VFQFN 裸露焊盘 |
| 供应商设备封装： | 32-QFN 裸露焊盘（5x5） |
| 包装： | 管件 |
9
FN8037.7
June 10, 2010
Software Controlled (Manual) Power-down
Most devices in the ISL4241E, ISL4243E family provide pins
that allow the user to force the IC into the low power, standby
state.
On the ISL4241E, the power-down control is via a simple
shutdown (SHDN) pin. Driving this pin high enables normal
operation, while driving it low forces the IC into it’s
power-down state. Connect SHDN to VCC if the power-down
function isn’t needed. Note that all the receiver outputs
remain enabled during shutdown (see Table 2). For the
lowest power consumption during power-down, the receivers
should also be disabled by driving the EN input high (see
The ISL4243E utilize a two pin approach where the
FORCEON and FORCEOFF inputs determine the IC’s
mode. For always enabled operation, FORCEON and
FORCEOFF are both strapped high. To switch between
active and power-down modes, under logic or software
control, only the FORCEOFF input need be driven. The
FORCEON state isn’t critical, as FORCEOFF dominates
over FORCEON. Nevertheless, if strictly manual control over
power-down is desired, the user must strap FORCEON high
to disable the automatic power-down circuitry. The ISL4243E
inverting (standard) receiver outputs also disable when the
device is in manual power-down, thereby eliminating the
possible current path through a shutdown peripheral’s input
Connecting FORCEOFF and FORCEON together disables
the automatic power-down feature, enabling them to function
as a manual SHUTDOWN input (see Figure 4).
With any of the previous mentioned control schemes, the
time required to exit power-down, and resume transmission
is only 100s. A mouse, or other application, may need more
time to wake up from shutdown. If automatic power-down is
being utilized, the RS-232 device will reenter power-down if
valid receiver levels aren’t reestablished within 30s of the
ISL4243E powering up. Figure 5 illustrates a circuit that
keeps the ISL4243E from initiating automatic power-down
for 100ms after powering up. This gives the slow-to-wake
peripheral circuit time to reestablish valid RS-232 output
levels.
INVALID Output (ISL4243E Only)
The INVALID output always indicates whether or not a valid
RS-232 signal (see Figure 6) is present at any of the
receiver inputs (see Table 2), giving the user an easy way to
determine when the interface block should power down.
Invalid receiver levels occur whenever the driving
peripheral’s outputs are shut off (powered down) or when the
RS-232 interface cable is disconnected. In the case of a
disconnected interface cable where all the receiver inputs
are floating (but pulled to GND by the internal receiver pull
down resistors), the INVALID logic detects the invalid levels
and drives the output low. The power management logic
FIGURE 3. DISABLED RECEIVERS PREVENT POWER DRAIN
ISL4241E
TRANSITION
RX
TX
R2OUTB
R2OUT
T1IN
FORCEOFF = GND
VCC
TO
R2IN
T1OUT
VOUT = HI-Z
POWERED
DETECTOR
DOWN
UART
WAKE-UP
LOGIC
OR
SHDN = GND, EN = VCC
ISL4243E
FIGURE 4. CONNECTIONS FOR MANUAL POWER-DOWN
WHEN NO VALID RECEIVER SIGNALS ARE
PRESENT
PWR
FORCEOFF
INVALID
CPU
I/O
FORCEON
ISL4243E
MGT
LOGIC
UART
FIGURE 5. CIRCUIT TO PREVENT AUTO POWER-DOWN
FOR 100ms AFTER FORCED POWERUP
ISL4243E
FORCEOFF
FORCEON
POWER
MASTER POWER-DOWN LINE
1M
Ω
0.1F
MANAGEMENT
UNIT
ISL4241E, ISL4243E
相关PDF资料 |
PDF描述 |
|---|---|
| VI-J3M-MX-F4 | CONVERTER MOD DC/DC 10V 75W |
| V48A15T500BG2 | CONVERTER MOD DC/DC 15V 500W |
| MS27468E13A35S | CONN RCPT 22POS JAM NUT W/SCKT |
| V48A15T500BF | CONVERTER MOD DC/DC 15V 500W |
| MS3106E-32-15P | CONN PLUG 8POS STRAIGHT W/PINS |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL4241EIRZ-T | 功能描述:IC XMITTER/RCVR ESD RS232 32-QFN RoHS:是 类别:集成电路 (IC) >> 接口 - 驱动器，接收器，收发器 系列:- 标准包装:2,500 系列:- 类型:驱动器 驱动器/接收器数:4/0 规程:RS422 电源电压:4.5 V ~ 5.5 V 安装类型:表面贴装 封装/外壳:16-SOIC（0.154"，3.90mm 宽） 供应商设备封装:16-SOIC N 包装:带卷 (TR) |
| ISL4243E | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:QFN Packaged, ±15kV ESD Protected, +2.7V to +5.5V, 10Nanoamp, 250kbps, +2.7V to +5.5V, 10Nanoamp, 250kbps, |
| ISL4243EIR | 功能描述:RS-232接口集成电路 TXRX 2.7-5.5V ESD RoHS:否 制造商:Exar 数据速率:52 Mbps 工作电源电压:5 V 电源电流:300 mA 工作温度范围:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体:LQFP-100 封装: |
| ISL4243EIR-T | 功能描述:IC 3DRVR/5RCVR RS232 3V 32-QFN RoHS:否 类别:集成电路 (IC) >> 接口 - 驱动器，接收器，收发器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:25 系列:- 类型:收发器 驱动器/接收器数:2/2 规程:RS232 电源电压:4.5 V ~ 5.5 V 安装类型:通孔 封装/外壳:16-DIP（0.300"，7.62mm） 供应商设备封装:16-PDIP 包装:管件 |
| ISL4243EIRZ | 功能描述:RS-232接口集成电路 RS232 3V 3D/5R 15KV AUTODWN 32QFN IND RoHS:否 制造商:Exar 数据速率:52 Mbps 工作电源电压:5 V 电源电流:300 mA 工作温度范围:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体:LQFP-100 封装: |
发布紧急采购，3分钟左右您将得到回复。