- 您现在的位置：买卖IC网 > PDF目录11174 > ISL43741IRZ-T (Intersil)IC MUX/DEMUX DUAL 4X1 20QFN PDF资料下载
参数资料
| 型号： | ISL43741IRZ-T |
| 厂商： | Intersil |
| 文件页数： | 5/17页 |
| 文件大小： | 0K |
| 描述： | IC MUX/DEMUX DUAL 4X1 20QFN |
| 标准包装： | 6,000 |
| 功能： | 多路复用器/多路分解器 |
| 电路： | 2 x 4:1 |
| 导通状态电阻： | 45 欧姆 |
| 电压电源： | 单/双电源 |
| 电压 - 电源，单路/双路(±)： | 2 V ~ 12 V，±2 V ~ 6 V |
| 电流 - 电源： | 7µA |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 20-VFQFN 裸露焊盘 |
| 供应商设备封装： | 20-QFN 裸露焊盘（4x4） |
| 包装： | 带卷 (TR) |
13
FN6053.3
March 13, 2006
Detailed Description
The ISL43681 and ISL43741 multiplexers offer precise
switching capability from a bipolar ±2V to ±6V or a single 2V
to 12V supply with low on-resistance (39
) and high speed
operation (tON =38ns, tOFF = 19ns) with dual 5V supplies.
They have an inhibit and inhibit bar pin to simultaneously
open all signal paths. They also have a latch bar pin to lock
in the last switch address.
The devices are especially well suited for applications using
±5V supplies. With ±5V supplies the performance (RON,
Leakage, Charge Injection, etc.) is best in class.
High frequency applications also benefit from the wide
bandwidth, and the very high off isolation and crosstalk
rejection.
Supply Sequencing And Overvoltage Protection
With any CMOS device, proper power supply sequencing is
required to protect the device from excessive input currents
which might permanently damage the IC. All I/O pins contain
ESD protection diodes from the pin to V+ and to V- (see
Figure 9). To prevent forward biasing these diodes, V+ and
V- must be applied before any input signals, and input signal
voltages must remain between V+ and V-. If these conditions
cannot be guaranteed, then one of the following two
protection methods should be employed.
Logic inputs can easily be protected by adding a 1k
resistor in series with the input (see Figure 9). The resistor
limits the input current below the threshold that produces
permanent damage, and the sub-microamp input current
produces an insignificant voltage drop during normal
operation.
This method is not applicable for the signal path inputs.
Adding a series resistor to the switch input defeats the
purpose of using a low RON switch, so two small signal
diodes can be added in series with the supply pins to provide
overvoltage protection for all pins (see Figure 9). These
additional diodes limit the analog signal from 1V below V+ to
1V above V-. The low leakage current performance is
unaffected by this approach, but the switch resistance may
increase, especially at low supply voltages.
Power-Supply Considerations
The ISL43681 and ISL43741 construction is typical of most
CMOS analog switches, in that they have three supply pins:
V+, V-, and GND. V+ and V- drive the internal CMOS
switches and set their analog voltage limits, so there are no
connections between the analog signal path and GND.
Unlike switches with a 13V maximum supply voltage, the
ISL43681 and ISL43741 15V maximum supply voltage
provides plenty of room for the 10% tolerance of 12V
supplies (±6V or 12V single supply), as well as room for
overshoot and noise spikes.
This family of switches performs equally well when operated
with bipolar or single voltage supplies.The minimum
FIGURE 7. CROSSTALK TEST CIRCUIT
FIGURE 8. CAPACITANCE TEST CIRCUIT
Test Circuits and Waveforms (Continued)
0V or V+
ANALYZER
NOA or NCA
SIGNAL
GENERATOR
RL
GND
ADDX
50
N.C.
COMB
NOB or NCB
EN
V-
C
V+
C
COMA
EN, LE
ISL43741
GND
NO or NC
COM
ADDX
IMPEDANCE
ANALYZER
0V or V+
EN
V-
C
V+
C
EN, LE
FIGURE 9. INPUT OVERVOLTAGE PROTECTION
VCOM
VNO or NC
OPTIONAL PROTECTION
V+
LOGIC
DIODE
OPTIONAL PROTECTION
DIODE
OPTIONAL
PROTECTION
RESISTOR
FOR LOGIC
INPUTS
1k
V-
ISL43681, ISL43741
相关PDF资料 |
PDF描述 |
|---|---|
| ISL43681IRZ-T | IC MUX/DEMUX 8X1 20QFN |
| ISL43231IRZ-T | IC SWITCH TRIPLE SPDT 20QFN |
| ISL84684IUZ | IC SWITCH DUAL SPDT 10MSOP |
| ISL8484IUZ | IC SWITCH DUAL SPDT 10MSOP |
| ISL43L120IRZ-T | IC SWITCH DUAL SPST 8TDFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL43840 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Low-Voltage, Single and Dual Supply, Dual 4 to 1 Multiplexer Analog Switch with Enable |
| ISL43840_06 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Low-Voltage, Single and Dual Supply, Dual 4 to 1 Multiplexer Analog Switch with Enable |
| ISL43840IR | 功能描述:IC MUX/DEMUX DUAL 4X1 20QFN RoHS:否 类别:集成电路 (IC) >> 接口 - 模拟开关，多路复用器，多路分解器 系列:- 标准包装:48 系列:- 功能:开关 电路:4 x SPST - NO 导通状态电阻:100 欧姆 电压电源:单/双电源 电压 - 电源，单路/双路(±):2 V ~ 12 V，±2 V ~ 6 V 电流 - 电源:50nA 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:16-SOIC（0.154"，3.90mm 宽） 供应商设备封装:16-SOIC 包装:管件 |
| ISL43840IR-T | 功能描述:IC MUX/DEMUX DUAL 4X1 20QFN RoHS:否 类别:集成电路 (IC) >> 接口 - 模拟开关，多路复用器，多路分解器 系列:- 标准包装:48 系列:- 功能:开关 电路:4 x SPST - NO 导通状态电阻:100 欧姆 电压电源:单/双电源 电压 - 电源，单路/双路(±):2 V ~ 12 V，±2 V ~ 6 V 电流 - 电源:50nA 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:16-SOIC（0.154"，3.90mm 宽） 供应商设备封装:16-SOIC 包装:管件 |
| ISL43840IRZ | 功能描述:多路器开关 IC SWITCH DL 4:1 MUX ENABLE +/-5V 60OHM RoHS:否 制造商:Texas Instruments 通道数量:1 开关数量:4 开启电阻（最大值）:7 Ohms 开启时间（最大值）: 关闭时间（最大值）: 传播延迟时间:0.25 ns 工作电源电压:2.3 V to 3.6 V 工作电源电流: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UQFN-16 |
发布紧急采购，3分钟左右您将得到回复。