- 您现在的位置：买卖IC网 > PDF目录384520 > ISL5239KI (INTERSIL CORP) Pre-Distortion Linearizer PDF资料下载
参数资料
| 型号： | ISL5239KI |
| 厂商： | INTERSIL CORP |
| 元件分类： | 消费家电 |
| 英文描述： | Pre-Distortion Linearizer |
| 中文描述： | SPECIALTY CONSUMER CIRCUIT, PBGA196 |
| 封装： | 15 X 15 MM, PLASTIC, BGA-196 |
| 文件页数： | 12/31页 |
| 文件大小： | 653K |
| 代理商： | ISL5239KI |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页当前第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页
12
General Comments About Modes
Once a trigger is detected in the ARMED condition, all
following triggers are ignored during the sequence. The
system does not acknowledge new triggers until a new
transaction is invoked and re-armed. When a new mode is
invoked, all subsequent invocations of new modes during the
duration of its sequence is ignored, except in the loop mode.
In the loop mode, an input memory mode change to IDLE is
processed immediately.
When in the IDLE, all controls, addresses, and data, default
to the processor interface values.
Triggers
When a capture memory is ARMED, i.e. waiting for a trigger
to happen, the activation of the trigger occurs in three ways
— external, data dependent, and user invoked. The trigger
select, 0x04, bits 5:4, provides the selection of the trigger
source. When the pre-distorter magnitude bus values fall
between the range of 0x09 minimum and 0x0a maximum,
the data dependent trigger activates. The first of these
transitions causes a trigger to be detected and the remaining
triggers during the capture sequence is ignored.
To invoke the user invoked trigger, 0x04, 5:4, set to
processor, the programmer writes a TRIGGER to the 0x04,
bit 6 processor trigger register. After a TRIGGER is in the
field, the user initiates the trigger by just writing to that
register. The user does not have to reset the trigger back to
IDLE. By setting the processor trigger bit to IDLE when not in
use, it keeps the circuit quiet and allows the user to write to
other values at that address without causing a trigger to
occur during operation. To disable the processor trigger, the
user should change trigger select to something other than
PROCESSOR and then change values in processor trigger.
If trigger select is not set to PROCESSOR, the system
ignores the trigger generated by processor trigger.
The feedback and input memory circuit uses the same
trigger; both circuits trigger at the same point with its
operation registers causing different operations to occur. The
user should monitor input memory status and feedback
memory status simultaneously before activating triggers.
Make sure both status registers are in ARMED before
activating triggers or the results from the capture can be
erroneous and data can be overwritten. Selecting processor
trigger (register 0x04, bits 5:4 = 00) while arming the input
and feedback memory circuits is a convenient way to ensure
no unexpected triggers occur before confirming ARMED
status of both circuits.
Input Data to Input Memory
There are three sources of input data to the input memory —
interpolator, pre-distorter’s data outputs, and the pre-
distorter’s magnitude. Data from the interpolator and the
predistort output are the upper 16 bits with or without
rounding. Only 16 of the original 20 bits of I or Q is loaded
into the memory. The I data is read from the memory on the
DataHigh register and the Q data, DataLow register.
In the predistort magnitude input, the data is unsigned 16
bits and the software has to reshuffle the data to extract the
original magnitude. The DataHigh contains only the pre-
distorter magnitude bit 15, and the DataLow contains the
pre-distorter magnitude 14:0.
Writing/Reading the Memories from the Processor
Interface
In the auto-increment mode, the data is loaded in 16-bit
increments. The low word is written or read first followed by
the high word. The high word increments the address
counter and generates the actual write to the memory. For
reading, it just increments the counter. The input memory
select 0x04, bit 12, selects the memory to be written to or
read from.
When writing or reading a specific address, the 0x0b
address register must be loaded before the 0x0c and 0x0d
memory data registers. In the write, the high word
transaction will trigger the actual write to the memory and a
low word must be written first. For additional details, see the
uP interface section.
Microprocessor Interface
The microprocessor interface allows the ISL5239 to appear
as a memory mapped peripheral to the
μ
P. All registers can
be accessed through this interface. The interface consists of
a 16 bit bidirectional data bus, P<15:0>, six bit address bus,
A<5:0>, a write strobe (WR), a read strobe (RD) and a chip
enable (CE). The interface is configured for separate read
and write strobe inputs.
The processor interface provides a simple parallel
Data/Control/Address bus for monitoring and controlling its
operation. The processor interface is asynchronous to the
CLK, and BUSY signal is included to indicate when read and
write operations are complete.
The register configuration is master/slave, where the slave
registers are updated from the masters and all reads access
the slaves.
The master registers are clocked by the
μ
P WR strobe, are
writable and cleared by a hard reset. The slave registers are
clocked by CLK, and are readable and cleared by either a
hard or soft reset. The transfer of configuration data from the
master register to the slave register occurs synchronously
after an event and requires a four clock synchronization
period.
The
μ
P can perform back-to-back accesses to the register,
but must maintain four f
CLK
periods between accesses to
the same address. This limits the maximum
μ
P access rate
for the RAM to 125MHz/4 = 31.25MHz.
ISL5239
相关PDF资料 |
PDF描述 |
|---|---|
| ISL5239KIZ | Pre-Distortion Linearizer |
| ISL5416 | Four-Channel Wideband Programmable DownConverter |
| ISL5416EVAL | Four-Channel Wideband Programmable DownConverter |
| ISL5416KI | Four-Channel Wideband Programmable DownConverter |
| ISL54205A | MP3/USB 2.0 High Speed Switch with Negative Signal Handling |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL5239KIZ | 功能描述:音频 DSP PA LINEARIZER IND 0MM PITCH BGA PACKAG RoHS:否 制造商:Texas Instruments 工作电源电压: 电源电流: 工作温度范围: 安装风格: 封装 / 箱体: 封装:Tube |
| ISL5314 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Direct Digital Synthesizer |
| ISL5314_05 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Direct Digital Synthesizer |
| ISL5314EVAL2 | 制造商:Intersil Corporation 功能描述:DEV TOOL FOR COMMLINK DIRECT DGTL SYNTHESIZER - Bulk |
| ISL5314IN | 功能描述:IC SYNTHESIZER DIGITAL 48-MQFP RoHS:否 类别:集成电路 (IC) >> 接口 - 直接数字合成 (DDS) 系列:- 产品变化通告:Product Discontinuance 27/Oct/2011 标准包装:2,500 系列:- 分辨率（位）:10 b 主 fclk:25MHz 调节字宽（位）:32 b 电源电压:2.97 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:16-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:16-TSSOP 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。