- 您现在的位置：买卖IC网 > PDF目录383134 > ISL54200IRUZ-T (INTERSIL CORP) USB 2.0 High/Full Speed Multiplexer PDF资料下载
参数资料
| 型号： | ISL54200IRUZ-T |
| 厂商： | INTERSIL CORP |
| 元件分类： | 运动控制电子 |
| 英文描述： | USB 2.0 High/Full Speed Multiplexer |
| 中文描述： | DUAL 1-CHANNEL, SGL POLE DOUBLE THROW SWITCH, PQCC10 |
| 封装： | 2.10 X 1.60 MM, ROHS COMPLIANT, PLASTIC, MO-255UABD, UTQFN-10 |
| 文件页数： | 9/16页 |
| 文件大小： | 1115K |
| 代理商： | ISL54200IRUZ-T |
9
FN6408.1
July 11, 2007
The HSx switches can also pass USB full-speed signals
(12Mbps) with minimal distortion and meet all the USB
requirements for USB 2.0 full-speed signaling. See Figure 11.
The maximum signal range for the HSx switches is from
-1.5V to V
DD
. The signal voltage should not be allow to
exceed the V
DD
voltage rail or go below ground by more
than -1.5V.
The HSx switches are active (turned ON) whenever the IN
voltage is
≥
1.4V and the EN logic voltage
≥
1.4V when
operated with a 2.7V to 3.6V supply.
ISL54200 Operation
The discussion that follows will discuss using the ISL54200 in
the typical application shown in the“Application Block
Diagram” on page 8.
POWER
The power supply connected at the VDD (pin 1) provides the
DC bias voltage required by the ISL54200 part for proper
operation. The ISL54200 can be operated with a VDD
voltage in the range of 2.7V to 5.5V. When used in a USB
application, the VDD voltage should be kept in the range of
3.0V to 5.5V to ensure you get the proper signal levels for
good signal quality.
A 0.01μF or 0.1μF decoupling capacitor should be
connected from the VDD pin to ground to filter out any power
supply noise from entering the part. The capacitor should be
located as close to the VDD pin as possible.
LOGIC CONTROL
The state of the ISL54200 device is determined by the
voltage at the IN pin (pin 2) and the EN pin (pin 10). IN is
only active when the EN pin is logic “1” (High). Refer to the
“Truth Table” on page 2.
The EN pin is internally pulled low through a 4M
Ω
resistor to
ground. For logic “0” (Low) it can be driven low or allowed to
Float. The IN pin must be driven low or high and cannot be
left floating.
Logic control voltage levels:
EN = Logic “0” (Low) when V
EN
≤
0.5V or Floating.
EN = Logic “1” (High) when V
EN
≥
1.4V
IN = Logic “0” (Low) when V
IN
≤
0.5V.
IN = Logic “1” (High) when V
IN
≥
1.4V
Full-speed Mode
If the IN pin = Logic “0” and the EN pin = Logic “1”, the part
will be in the full-speed mode. In this mode, the FSD1 and
FSD2 switches are ON and the HSD1 and HSD2 switches
are OFF (high impedance). In a typical application, V
DD
will
be in the range of 2.8V to 3.6V and will be connected to the
battery or LDO of the portable media device. When a
computer or USB hub is plugged into the common USB
connector and the part is in the full-speed mode, a link will
be established between the full-speed driver section of the
media player and the computer. The device will be able to
transmit and receive data from the computer at a data rate of
12Mbps.
High-speed Mode
If the IN pin = Logic “1” and the EN pin = Logic “1”, the part
will go into high-speed mode. In high-speed mode, the
HSD1 and HSD2 switches are ON and the FSD1 and FSD2
switches are OFF (high impedance). When a USB cable
from a computer or USB hub is connected at the common
USB connector and the part is in the high-speed mode, a link
will be established between the high-speed driver section of
the media player and the computer. The device will be able
to transmit and receive data from the computer at a data rate
of 480Mbps.
All Switches OFF Mode
If the IN pin = Logic “0” or Logic “1” and the EN pin = Logic “0”,
all of the switches will turn OFF (high impedance).
The all OFF state can be used to switch between the two
USB sections of the media player. When disconnecting from
one USB device to the other USB device, you can
momentarily put the ISL54200 switch in the “all off” state in
order to get the computer to disconnect from the one device
so it can properly connect to the other USB device when that
channel is turned ON.
ISL54200
相关PDF资料 |
PDF描述 |
|---|---|
| ISL54200 | USB 2.0 High/Full Speed Multiplexer |
| ISL54200IRZ | USB 2.0 High/Full Speed Multiplexer |
| ISL54200IRZ-T | USB 2.0 High/Full Speed Multiplexer |
| ISL54400EVAL1Z | Low Voltage, Dual SPDT, USB/Audio Switches with Negative Signal Capability |
| ISL54400IRUZ-T | Low Voltage, Dual SPDT, USB/Audio Switches with Negative Signal Capability |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL54200IRZ | 功能描述:IC USB SWITCH DUAL SPDT 10TDFN RoHS:是 类别:集成电路 (IC) >> 接口 - 模拟开关，多路复用器，多路分解器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:36 系列:- 功能:多路复用器 电路:2 x 4:1 导通状态电阻:75 欧姆 电压电源:单/双电源 电压 - 电源，单路/双路(±):2 V ~ 12 V，±2 V ~ 6 V 电流 - 电源:- 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:20-SOIC（0.295"，7.50mm 宽） 供应商设备封装:20-SOIC W 包装:管件 |
| ISL54200IRZ-T | 功能描述:IC USB SWITCH DUAL SPDT 10TDFN RoHS:是 类别:集成电路 (IC) >> 接口 - 模拟开关，多路复用器，多路分解器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:36 系列:- 功能:多路复用器 电路:2 x 4:1 导通状态电阻:75 欧姆 电压电源:单/双电源 电压 - 电源，单路/双路(±):2 V ~ 12 V，±2 V ~ 6 V 电流 - 电源:- 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:20-SOIC（0.295"，7.50mm 宽） 供应商设备封装:20-SOIC W 包装:管件 |
| ISL54205A | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:MP3/USB 2.0 High Speed Switch with Negative Signal Handling |
| ISL54205AEVAL1Z | 制造商:Intersil Corporation 功能描述:ISL54205A EVALUATION BOARD 1 - ROHS COMPLIANT - UTQFN - Bulk |
| ISL54205AIRUZ-T | 功能描述:IC SWITCH MP3/USB2.0 HS 10-TQFN RoHS:是 类别:集成电路 (IC) >> 接口 - 模拟开关，多路复用器，多路分解器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:36 系列:- 功能:多路复用器 电路:2 x 4:1 导通状态电阻:75 欧姆 电压电源:单/双电源 电压 - 电源，单路/双路(±):2 V ~ 12 V，±2 V ~ 6 V 电流 - 电源:- 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:20-SOIC（0.295"，7.50mm 宽） 供应商设备封装:20-SOIC W 包装:管件 |
发布紧急采购，3分钟左右您将得到回复。