参数资料
| 型号： | ISL55004IB-T13 |
| 厂商： | Intersil |
| 文件页数： | 12/12页 |
| 文件大小： | 0K |
| 描述： | IC OPAMP QUAD 200MHZ 14-SOIC |
| 标准包装： | 2,500 |
| 放大器类型： | 电压反馈 |
| 电路数： | 4 |
| 转换速率： | 300 V/µs |
| 增益带宽积： | 70MHz |
| -3db带宽： | 200MHz |
| 电流 - 输入偏压： | 600nA |
| 电压 - 输入偏移： | 1200µV |
| 电流 - 电源： | 8.5mA |
| 电流 - 输出 / 通道： | 140mA |
| 电压 - 电源，单路/双路(±)： | 4.5 V ~ 30 V，±2.25 V ~ 15 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 14-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 14-SOIC |
| 包装： | 带卷 (TR) |
9
FN6219.2
July 27, 2006
For sourcing:
For sinking:
Where:
VS = Supply voltage
ISMAX = Maximum quiescent supply current
VOUT = Maximum output voltage of the application
RLOAD = Load resistance tied to ground
ILOAD = Load current
N = number of amplifiers (max = 4)
By setting the two PDMAX equations equal to each other, we
can solve the output current and RLOAD to avoid the device
overheat.
Caution: For supply voltages greater then 20V, the
maximum power dissipation at 85°C ambient temperature
could be exceeded. For higher supply voltages the
maximum ambient temperature must be de-rated according
to the Package Power Dissipation curve Figure 27. The
maximum power dissipation is highly dependent upon the
thermal conductivity of the PCB. For lower thermal
conductivity boards use Figure 26.
Power Supply Bypassing Printed Circuit Board
Layout
As with any high frequency device, a good printed circuit
board layout is necessary for optimum performance. Lead
lengths should be as short as possible. The power supply
pin must be well bypassed to reduce the risk of oscillation.
For normal single supply operation, where the VS- pin is
connected to the ground plane, a single 4.7F tantalum
capacitor in parallel with a 0.1F ceramic capacitor from VS+
to GND will suffice. This same capacitor combination should
be placed at each supply pin to ground if split supplies are to
be used. In this case, the VS- pin becomes the negative
supply rail.
Printed Circuit Board Layout
For good AC performance, parasitic capacitance should be
kept to minimum. Use of wire wound resistors should be
avoided because of their additional series inductance. Use
of sockets should also be avoided if possible. Sockets add
parasitic inductance and capacitance that can result in
compromised performance. Minimizing parasitic capacitance
at the amplifier's inverting input pin is very important. The
feedback resistor should be placed very close to the
inverting input pin. Strip line design techniques are
recommended for the signal traces.
Application Circuits
Sallen Key Low Pass Filter
A common and easy to implement filter taking advantage of
the wide bandwidth, low offset and low power demands of
the ISL55004. A derivation of the transfer function is
provided for convenience (See Figure 28).
Sallen Key High Pass Filter
Again this useful filter benefits from the characteristics of the
ISL55004. The transfer function is very similar to the low
pass so only the results are presented (See Figure 29).
PD
MAX
V
S
I
SMAX
V
S
V
OUTi
–
()
i1
=
n
∑
V
OUTi
R
Li
-----------------
×
+
×
=
PD
MAX
V
S
I
SMAX
V
OUTi
V
S
–
()
i1
=
n
∑
I
LOADi
×
+
×
=
ISL55004
相关PDF资料 |
PDF描述 |
|---|---|
| TA45-A321M100C0 | CIRCUIT BRKR THERMAL 10A 2POLE |
| ICL7621DCBA-T | IC OPAMP DUAL 0.5MHZ CMOS 8-SOIC |
| S20K460E3K1 | VARISTOR 460V RMS 20MM RADIAL |
| TA45-A326F075C0 | CIRCUIT BRKR RCKR ILL 7.5A 2P QC |
| ICL7621DCBA | IC OPAMP DUAL 0.5MHZ CMOS 8-SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL55004IB-T7 | 功能描述:IC OPAMP QUAD 200MHZ 14-SOIC RoHS:否 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:50 系列:LinCMOS™ 放大器类型:通用 电路数:4 输出类型:- 转换速率:0.05 V/µs 增益带宽积:110kHz -3db带宽:- 电流 - 输入偏压:0.7pA 电压 - 输入偏移:210µV 电流 - 电源:57µA 电流 - 输出 / 通道:30mA 电压 - 电源，单路/双路(±):3 V ~ 16 V，±1.5 V ~ 8 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:14-SOIC（0.154"，3.90mm 宽） 供应商设备封装:14-SOIC 包装:管件 产品目录页面:865 (CN2011-ZH PDF) 其它名称:296-1834296-1834-5 |
| ISL55004IBZ | 功能描述:运算放大器 - 运放 ISL59115IRUZ-EVALZ EVAL BRD RHS COMPLI RoHS:否 制造商:STMicroelectronics 通道数量:4 共模抑制比（最小值）:63 dB 输入补偿电压:1 mV 输入偏流（最大值）:10 pA 工作电源电压:2.7 V to 5.5 V 安装风格:SMD/SMT 封装 / 箱体:QFN-16 转换速度:0.89 V/us 关闭:No 输出电流:55 mA 最大工作温度:+ 125 C 封装:Reel |
| ISL55004IBZ-T13 | 功能描述:IC OPAMP QUAD 200MHZ 14-SOIC RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 放大器类型:通用 电路数:2 输出类型:推挽式，满摆幅 转换速率:2.1 V/µs 增益带宽积:22MHz -3db带宽:- 电流 - 输入偏压:1pA 电压 - 输入偏移:70µV 电流 - 电源:420µA 电流 - 输出 / 通道:68mA 电压 - 电源，单路/双路(±):2.4 V ~ 5.5 V，±1.2 V ~ 2.75 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽） 供应商设备封装:10-µMAX 包装:带卷 (TR) |
| ISL55004IBZ-T7 | 功能描述:IC OPAMP 200MHZ UNITYGAIN 14SOIC RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 放大器类型:通用 电路数:2 输出类型:推挽式，满摆幅 转换速率:2.1 V/µs 增益带宽积:22MHz -3db带宽:- 电流 - 输入偏压:1pA 电压 - 输入偏移:70µV 电流 - 电源:420µA 电流 - 输出 / 通道:68mA 电压 - 电源，单路/双路(±):2.4 V ~ 5.5 V，±1.2 V ~ 2.75 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽） 供应商设备封装:10-µMAX 包装:带卷 (TR) |
| ISL55005 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:MMIC Silicon Bipolar Broadband Amplifier |
发布紧急采购，3分钟左右您将得到回复。