参数资料
型号: ISL59424IRZ-T7
厂商: INTERSIL CORP
元件分类: 运动控制电子
英文描述: 1GHz Triple Multiplexing Amplifiers
中文描述: TRIPLE 2-CHANNEL, VIDEO MULTIPLEXER, QCC24
封装: LEAD FREE, QFN-24
文件页数: 10/13页
文件大小: 780K
代理商: ISL59424IRZ-T7
10
FN7456.2
September 8, 2005
HIZ State
An internal pull-down resistor connected to the HIZ pin
ensures the device will be active with no connection to the
HIZ pin. The HIZ state is established within approximately
15ns (Figure 16) by placing a logic high (>2V) on the HIZ
pin. If the HIZ state is selected, the output is a high
impedance 1.4M
with approximately 1.5pF in parallel with
a 10
μ
A bias current from the output. Use this state to control
the logic when more than one mux shares a common output.
In the HIZ state the output is three-stated, and maintains its
high Z even in the presence of high slew rates. The supply
current during this state is basically the same as the active
state.
ENABLE and Power Down States
The enable pin is active low. An internal pull-down resistor
ensures the device will be active with no connection to the
ENABLE pin. The Power Down state is established within
approximately 100ns (Figure 14), if a logic high (>2V) is
placed on the ENABLE pin. In the Power Down state, the
output has no leakage but has a large variable capacitance
(on the order of 15pF), and is capable of being back-driven.
Under this condition, large incoming slew rates can cause
fault currents of tens of mA.
Do not use this state as a
logic control for applications driving more than one mux
on a common output.
LE State
The ISL59424 is equipped with a Latch Enable pin. A logic
high (>2V) on the LE pin latches the last logic state. This
logic state is preserved when cycling HIZ or ENABLE
functions.
Limiting the Output Current
No output short circuit current limit exists on these parts. All
applications need to limit the output current to less than
50mA. Adequate thermal heat sinking of the parts is also
required.
Application Example
Figure 21 illustrates the use of the ISL59445, two ISL84517
SPST switches and one NC7ST00P5X NAND gate to mux 3
different component video signals and one RGB video
signal. The SPDT switches provide the sync signal for the
RGB video and disconnects the sync signal for the
component signal.
PC Board Layout
The frequency response of this circuit depends greatly on
the care taken in designing the PC board. The following are
recommendations to achieve optimum high frequency
performance from your PC board.
The use of low inductance components such as chip
resistors and chip capacitors is strongly recommended.
Minimize signal trace lengths. Trace inductance and
capacitance can easily limit circuit performance. Avoid
sharp corners, use rounded corners when possible. Vias
in the signal lines add inductance at high frequency and
should be avoided. PCB traces greater than 1" begin to
exhibit transmission line characteristics with signal rise/fall
times of 1ns or less. High frequency performance may be
degraded for traces greater than one inch, unless strip line
are used.
Match channel-channel analog I/O trace lengths and
layout symmetry. This will minimize propagation delay
mismatches.
Maximize use of AC de-coupled PCB layers. All signal I/O
lines should be routed over continuous ground planes (i.e.
no split planes or PCB gaps under these lines). Avoid vias
in the signal I/O lines.
Use proper value and location of termination resistors.
Termination resistors should be as close to the device as
possible.
When testing use good quality connectors and cables,
matching cable types and keeping cable lengths to a
minimum.
Minimum of 2 power supply de-coupling capacitors are
recommended (1000pF, 0.01μF) as close to the devices
as possible - Avoid vias between the cap and the device
because vias add unwanted inductance. Larger caps can
be farther away. When vias are required in a layout, they
should be routed as far away from the device as possible.
The NIC pins are placed on both sides of the input pins.
These pins are not internally connected to the die. It is
recommended these pins be tied to ground to minimize
crosstalk.
V+
V+
V-
V-
V+
V-
V+
V-
LOGIC
CONTROL
GND
IN0
IN1
S0
OUT
EXTERNAL
CIRCUITS
SCHOTTKY
PROTECTION
V+
V-
POWER
GND
SIGNAL
LOGIC
V+ SUPPLY
V- SUPPLY
DE-COUPLING
CAPS
FIGURE 21. SCHOTTKY PROTECTION CIRCUIT
ISL59424, ISL59445
相关PDF资料
PDF描述
ISL59445 1GHz Triple Multiplexing Amplifiers(1GHz三倍多路放大器)
ISL59445IR-T13 1GHz Triple Multiplexing Amplifiers
ISL59445IR-T7 1GHz Triple Multiplexing Amplifiers
ISL59483IRZ Dual, 500MHz Triple, Multiplexing Amplifiers
ISL59483IRZ-T13 Dual, 500MHz Triple, Multiplexing Amplifiers
相关代理商/技术参数
参数描述
ISL59440 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:400MHz Multiplexing Amplifier
ISL59440_07 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:400MHz Multiplexing Amplifier
ISL59440IA 功能描述:IC AMP MULTIPLEX 400MHZ 16-QSOP RoHS:否 类别:集成电路 (IC) >> 线性 - 放大器 - 视频放大器和频缓冲器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:50 系列:- 应用:TFT-LCD 面板:VCOM 驱动器 输出类型:满摆幅 电路数:1 -3db带宽:35MHz 转换速率:40 V/µs 电流 - 电源:3.7mA 电流 - 输出 / 通道:1.3A 电压 - 电源,单路/双路(±):9 V ~ 20 V,±4.5 V ~ 10 V 安装类型:表面贴装 封装/外壳:8-TSSOP,8-MSOP(0.118",3.00mm 宽)裸露焊盘 供应商设备封装:8-uMax-EP 包装:管件
ISL59440IA-EVAL 制造商:Intersil Corporation 功能描述:EVAL KIT FOR 400MHZ MULTIPLEXING AMP - Bulk
ISL59440IA-T13 功能描述:IC AMP MULTIPLEX 400MHZ 16-QSOP RoHS:否 类别:集成电路 (IC) >> 线性 - 放大器 - 视频放大器和频缓冲器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:50 系列:- 应用:TFT-LCD 面板:VCOM 驱动器 输出类型:满摆幅 电路数:1 -3db带宽:35MHz 转换速率:40 V/µs 电流 - 电源:3.7mA 电流 - 输出 / 通道:1.3A 电压 - 电源,单路/双路(±):9 V ~ 20 V,±4.5 V ~ 10 V 安装类型:表面贴装 封装/外壳:8-TSSOP,8-MSOP(0.118",3.00mm 宽)裸露焊盘 供应商设备封装:8-uMax-EP 包装:管件