参数资料
| 型号： | ISL59440IAZ |
| 厂商： | Intersil |
| 文件页数： | 3/12页 |
| 文件大小： | 0K |
| 描述： | IC AMP MULTIPLEX 400MHZ 16-QSOP |
| 标准包装： | 97 |
| 应用： | 4:1 多路复用器-放大器 |
| 电路数： | 1 |
| -3db带宽： | 400MHz |
| 转换速率： | 1470 V/µs |
| 电流 - 电源： | 14.5mA |
| 电流 - 输出 / 通道： | 130mA |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-SSOP（0.154"，3.90mm 宽） |
| 供应商设备封装： | 16-QSOP |
| 包装： | 管件 |
| 产品目录页面： | 1235 (CN2011-ZH PDF) |
11
FN6162.2
October 10, 2007
PC Board Layout
The frequency response of this circuit depends greatly on
the care taken in designing the PC board. The following are
recommendations to achieve optimum high frequency
performance from your PC board.
The use of low inductance components such as chip
resistors and chip capacitors is strongly recommended.
Match channel-channel analog I/O trace lengths and
layout symmetry. This will minimize propagation delay
mismatches.
Maximize use of AC de-coupled PCB layers. All signal I/O
lines should be routed over continuous ground planes (i.e.
no split planes or PCB gaps under these lines). Avoid vias
in the signal I/O lines.
Use proper value and location of termination resistors.
Termination resistors should be as close to the device as
possible.
When testing use good quality connectors and cables,
matching cable types and keeping cable lengths to a
minimum.
Minimum of 2 power supply de-coupling capacitors are
recommended (1000pF, 0.01F) as close to the device as
possible - Avoid vias between the cap and the device
because vias add unwanted inductance. Larger caps can
be farther away. When vias are required in a layout, they
should be routed as far away from the device as possible.
The NIC pins are placed on both sides of the input pins.
These pins are not internally connected to the die. It is
recommended these pins be tied to ground to minimize
crosstalk.
ISL59440
相关PDF资料 |
PDF描述 |
|---|---|
| ISL59420IUZ-T7 | IC AMP MULTIPLEX 400MHZ 10-MSOP |
| AD7542JPZ | IC DAC 12BIT MULT CMOS 20-PLCC |
| DAC8222FSZ-REEL | IC DAC 12BIT DUAL CMOS 24SOIC |
| DAC8248FSZ-REEL | IC DAC 12BIT DUAL W/BUFF 24SOIC |
| AD7547LRZ-REEL | IC DAC 12BIT DUAL LC2MOS 24-SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL59440IAZ-T13 | 制造商:Intersil Corporation 功能描述:ANLG MUX/AMP SGL 4:1 5.5V 16QSOP - Tape and Reel 制造商:Intersil 功能描述:ISL8036CRSH EVALRD 1 24LD RHS COMP |
| ISL59440IAZ-T7 | 功能描述:IC AMP 400MHZ MULTIPLEX 16-QSOP RoHS:是 类别:集成电路 (IC) >> 线性 - 放大器 - 视频放大器和频缓冲器 系列:- 标准包装:1,000 系列:- 应用:驱动器 输出类型:差分 电路数:3 -3db带宽:350MHz 转换速率:1000 V/µs 电流 - 电源:14.5mA 电流 - 输出 / 通道:60mA 电压 - 电源，单路/双路(±):5 V ~ 12 V，±2.5 V ~ 6 V 安装类型:表面贴装 封装/外壳:20-VFQFN 裸露焊盘 供应商设备封装:20-QFN 裸露焊盘（4x4） 包装:带卷 (TR) |
| ISL59441 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:900MHz Multiplexing Amplifier |
| ISL59441IA | 功能描述:IC AMP MULTIPLEX 900MHZ 16-QSOP RoHS:否 类别:集成电路 (IC) >> 线性 - 放大器 - 视频放大器和频缓冲器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:50 系列:- 应用:TFT-LCD 面板：VCOM 驱动器 输出类型:满摆幅 电路数:1 -3db带宽:35MHz 转换速率:40 V/µs 电流 - 电源:3.7mA 电流 - 输出 / 通道:1.3A 电压 - 电源，单路/双路(±):9 V ~ 20 V，±4.5 V ~ 10 V 安装类型:表面贴装 封装/外壳:8-TSSOP，8-MSOP（0.118"，3.00mm 宽）裸露焊盘 供应商设备封装:8-uMax-EP 包装:管件 |
| ISL59441IA-T13 | 功能描述:IC AMP MULTIPLEX 900MHZ 16-QSOP RoHS:否 类别:集成电路 (IC) >> 线性 - 放大器 - 视频放大器和频缓冲器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:50 系列:- 应用:TFT-LCD 面板：VCOM 驱动器 输出类型:满摆幅 电路数:1 -3db带宽:35MHz 转换速率:40 V/µs 电流 - 电源:3.7mA 电流 - 输出 / 通道:1.3A 电压 - 电源，单路/双路(±):9 V ~ 20 V，±4.5 V ~ 10 V 安装类型:表面贴装 封装/外壳:8-TSSOP，8-MSOP（0.118"，3.00mm 宽）裸露焊盘 供应商设备封装:8-uMax-EP 包装:管件 |
发布紧急采购，3分钟左右您将得到回复。