- 您现在的位置：买卖IC网 > PDF目录383137 > ISL59441IAZ-T13 (INTERSIL CORP) 900MHz Multiplexing Amplifier PDF资料下载
参数资料
| 型号： | ISL59441IAZ-T13 |
| 厂商： | INTERSIL CORP |
| 元件分类： | 运动控制电子 |
| 英文描述： | 900MHz Multiplexing Amplifier |
| 中文描述： | 4-CHANNEL, VIDEO MULTIPLEXER, PDSO16 |
| 封装： | LEAD FREE, 0.150 INCH, QSOP-16 |
| 文件页数： | 10/12页 |
| 文件大小： | 571K |
| 代理商： | ISL59441IAZ-T13 |
10
FN6163.2
September 21, 2005
Control Signals
S0, S1, ENABLE, HIZ - These pins are TTL/CMOS
compatible control inputs. The S0 pin selects which one of
the inputs connect to the output. The ENABLE, HIZ pins are
used to disable the part to save power and three-state the
output amplifiers, respectively. For control signal rise and fall
times less than 10ns the use of termination resistors close to
the part will minimize transients coupled to the output.
Power-Up Considerations
The ESD protection circuits use internal diodes from all pins
the V+ and V- supplies. In addition, a dV/dT- triggered clamp
is connected between the V+ and V- pins, as shown in the
Equivalent Circuits 1 through 4 section of the Pin Description
table. The dV/dT triggered clamp imposes a maximum
supply turn-on slew rate of 1V/μs. Damaging currents can
flow for power supply rates-of-rise in excess of 1V/μs, such
as during hot plugging. Under these conditions, additional
methods should be employed to ensure the rate of rise is not
exceeded.
Consideration must be given to the order in which power is
applied to the V+ and V- pins, as well as analog and logic
input pins. Schottky diodes (Motorola MBR0550T or
equivalent) connected from V+ to ground and V- to ground
(Figure 26) will shunt damaging currents away from the
internal V+ and V- ESD diodes in the event that the V+
supply is applied to the device before the V- supply.
If positive voltages are applied to the logic or analog video
input pins before V+ is applied, current will flow through the
internal ESD diodes to the V+ pin. The presence of large
decoupling capacitors and the loading effect of other circuits
connected to V+, can result in damaging currents through
the ESD diodes and other active circuits within the device.
Therefore, adequate current limiting on the digital and
analog inputs is needed to prevent damage during the time
the voltages on these inputs are more positive than V+.
HIZ State
An internal pull-down resistor connected to the HIZ pin
ensures the device will be active with no connection to the
HIZ pin. The HIZ state is established within approximately
30ns (Figure 18) by placing a logic high (>2V) on the HIZ
pin. If the HIZ state is selected, the output is a high
impedance 1.4M
. Use this state to control the logic when
more than one mux shares a common output.
In the HIZ state the output is three-stated, and maintains its
high Z even in the presence of high slew rates. The supply
current during this state is basically the same as the active
state.
ENABLE & Power Down States
The enable pin is active low. An internal pull-down resistor
ensures the device will be active with no connection to the
ENABLE pin. The Power Down state is established when a
logic high (>2V) is placed on the ENABLE pin. In the Power
Down state, the output has no leakage but has a large
capacitance (on the order of 15pF), and is capable of being
back-driven. Under this condition, large incoming slew rates
can cause fault currents of tens of mA.
Do not use this
state as a high Z state for applications driving more than
one mux on a common output.
Limiting the Output Current
No output short circuit current limit exists on this part. All
applications need to limit the output current to less than
50mA. Adequate thermal heat sinking of the parts is also
required.
V+
V+
V-
V-
V+
V-
V+
V-
LOGIC
CONTROL
GND
IN0
IN1
S0
OUT
EXTERNAL
CIRCUITS
SCHOTTKY
PROTECTION
V+
V-
POWER
GND
SIGNAL
LOGIC
V+ SUPPLY
V- SUPPLY
DE-COUPLING
CAPS
FIGURE 26. SCHOTTKY PROTECTION CIRCUIT
ISL59441
相关PDF资料 |
PDF描述 |
|---|---|
| ISL59441IAZ-T7 | 900MHz Multiplexing Amplifier |
| ISL59442IB-T13 | 1GHz, 4 x 1 Multiplexing Amplifier |
| ISL59442 | 1GHz, 4 x 1 Multiplexing Amplifier |
| ISL59442IB-T7 | 1GHz, 4 x 1 Multiplexing Amplifier |
| ISL59442IB | 1GHz, 4 x 1 Multiplexing Amplifier |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL59441IAZ-T7 | 制造商:Intersil Corporation 功能描述:ANLG MUX/AMP SGL 4:1 5.5V 16QSOP - Tape and Reel 制造商:Intersil 功能描述:ISL8120 EVALRD 3 RHS CMPL -1 CON |
| ISL59442 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:1GHz, 4 x 1 Multiplexing Amplifier |
| ISL59442_07 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:1GHz, 4 x 1 Multiplexing Amplifier |
| ISL59442IB | 功能描述:IC CROSSPOINT SW 1GHZ 4X1 14SOIC RoHS:是 类别:集成电路 (IC) >> 线性 - 放大器 - 视频放大器和频缓冲器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:50 系列:- 应用:TFT-LCD 面板：VCOM 驱动器 输出类型:满摆幅 电路数:1 -3db带宽:35MHz 转换速率:40 V/µs 电流 - 电源:3.7mA 电流 - 输出 / 通道:1.3A 电压 - 电源，单路/双路(±):9 V ~ 20 V，±4.5 V ~ 10 V 安装类型:表面贴装 封装/外壳:8-TSSOP，8-MSOP（0.118"，3.00mm 宽）裸露焊盘 供应商设备封装:8-uMax-EP 包装:管件 |
| ISL59442IB-T13 | 功能描述:IC CROSSPOINT SW 1GHZ 4X1 14SOIC RoHS:否 类别:集成电路 (IC) >> 线性 - 放大器 - 视频放大器和频缓冲器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:50 系列:- 应用:TFT-LCD 面板：VCOM 驱动器 输出类型:满摆幅 电路数:1 -3db带宽:35MHz 转换速率:40 V/µs 电流 - 电源:3.7mA 电流 - 输出 / 通道:1.3A 电压 - 电源，单路/双路(±):9 V ~ 20 V，±4.5 V ~ 10 V 安装类型:表面贴装 封装/外壳:8-TSSOP，8-MSOP（0.118"，3.00mm 宽）裸露焊盘 供应商设备封装:8-uMax-EP 包装:管件 |
发布紧急采购，3分钟左右您将得到回复。