- 您现在的位置：买卖IC网 > PDF目录383137 > ISL59445IR-T7 (INTERSIL CORP) 1GHz Triple Multiplexing Amplifiers PDF资料下载
参数资料
| 型号： | ISL59445IR-T7 |
| 厂商： | INTERSIL CORP |
| 元件分类： | 运动控制电子 |
| 英文描述： | 1GHz Triple Multiplexing Amplifiers |
| 中文描述： | TRIPLE 4-CHANNEL, VIDEO MULTIPLEXER, QCC32 |
| 封装： | 2.48 X 3.4 MM, QFN-32 |
| 文件页数： | 9/13页 |
| 文件大小： | 780K |
| 代理商： | ISL59445IR-T7 |
9
FN7456.2
September 8, 2005
Figure 20A illustrates the optimum output load for testing AC
performance. Figure 20B illustrates the optimum output load
when connecting to 50
input terminated equipment.
Application Information
General
The ISL59424 and ISL59445 are triple 2:1 and 4:1 muxes
that are ideal for the matrix element of high performance
switchers and routers. The ISL59424 and ISL59445 are
optimized to drive a 1.5pF in parallel with a 500
load. The
capacitance can be split between the PCB capacitance an
and external load capacitance. Their low input capacitance
and high input resistance provide excellent 50
or 75
terminations.
Ground Connections
For the best isolation and crosstalk rejection, all GND pins
and NIC pins must connect to the GND plane.
Control Signals
S0, S1, ENABLE, LE, HIZ - These pins are binary coded,
TTL/CMOS compatible control inputs. The S0, S1 pins select
which one of the inputs connect to the output. All three
amplifiers are switched simultaneously from their respective
inputs. The ENABLE, LE, HIZ pins are used to disable the part
to save power, latch in the last logic state and three-state the
output amplifiers, respectively. For control signal rise and fall
times less than 10ns the use of termination resistors close to
the part should be considered to minimize transients coupled
to the output.
Power-Up Considerations
The ESD protection circuits use internal diodes from all pins
the V+ and V- supplies. In addition, a dV/dT- triggered clamp
is connected between the V+ and V- pins, as shown in the
Equivalent Circuits 1 through 4 section of the Pin Description
table. The dV/dT triggered clamp imposes a maximum
supply turn-on slew rate of 1V/μs. Damaging currents can
flow for power supply rates-of-rise in excess of 1V/μs, such
as during hot plugging. Under these conditions, additional
methods should be employed to ensure the rate of rise is not
exceeded.
Consideration must be given to the order in which power is
applied to the V+ and V- pins, as well as analog and logic
input pins. Schottky diodes (Motorola MBR0550T or
equivalent) connected from V+ to ground and V- to ground
(Figure 21) will shunt damaging currents away from the
internal V+ and V- ESD diodes in the event that the V+
supply is applied to the device before the V- supply.
If positive voltages are applied to the logic or analog video
input pins before V+ is applied, current will flow through the
internal ESD diodes to the V+ pin. The presence of large
decoupling capacitors and the loading effect of other circuits
connected to V+, can result in damaging currents through
the ESD diodes and other active circuits within the device.
Therefore, adequate current limiting on the digital and
analog inputs is needed to prevent damage during the time
the voltages on these inputs are more positive than V+.
AC Test Circuits
FIGURE 20A. TEST CIRCUIT WITH OPTIMAL OUTPUT LOAD
FIGURE 20B. TEST CIRCUIT FOR MEASURING WITH 50
OR
75
INPUT TERMINATED EQUIPMENT
FIGURE 20C. BACKLOADED TEST CIRCUIT FOR VIDEO CABLE APPLICATION. BANDWIDTH AND LINEARITY FOR R
L
LESS THAN 500
WILL BE DEGRADED.
FIGURE 20. TEST CIRCUITS
ISL59424 & ISL59445
C
L
1.5pF
50
or
75
V
IN
500
R
L
ISL59424 & ISL59445
R
S
C
L
1.5pF
V
IN
475
or
462.5
TEST
50
or
75
50
or
75
50
or
75
EQUIPMENT
ISL59424 & ISL59445
R
S
C
L
1.5pF
V
IN
50
or 75
TEST
50
or
75
50
or
75
EQUIPMENT
ISL59424, ISL59445
相关PDF资料 |
PDF描述 |
|---|---|
| ISL59483IRZ | Dual, 500MHz Triple, Multiplexing Amplifiers |
| ISL59483IRZ-T13 | Dual, 500MHz Triple, Multiplexing Amplifiers |
| ISL59483 | Dual, 500MHz Triple, Multiplexing Amplifiers |
| ISL59532IKEZ | 32x32 Video Crosspoint |
| ISL5957 | 14-Bit, +3.3V, 260+MSPS, High Speed D/A Converter |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL59445IRZ | 功能描述:IC AMP TRIPLE MUX 1GHZ 32-QFN RoHS:是 类别:集成电路 (IC) >> 线性 - 放大器 - 视频放大器和频缓冲器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:50 系列:- 应用:TFT-LCD 面板：VCOM 驱动器 输出类型:满摆幅 电路数:1 -3db带宽:35MHz 转换速率:40 V/µs 电流 - 电源:3.7mA 电流 - 输出 / 通道:1.3A 电压 - 电源，单路/双路(±):9 V ~ 20 V，±4.5 V ~ 10 V 安装类型:表面贴装 封装/外壳:8-TSSOP，8-MSOP（0.118"，3.00mm 宽）裸露焊盘 供应商设备封装:8-uMax-EP 包装:管件 |
| ISL59445IRZ-EVAL | 功能描述:EVAL BOARD FOR ISL59445 RoHS:否 类别:编程器，开发系统 >> 评估演示板和套件 系列:* 标准包装:1 系列:PSoC® 主要目的:电源管理，热管理 嵌入式:- 已用 IC / 零件:- 主要属性:- 次要属性:- 已供物品:板，CD，电源 |
| ISL59445IRZ-T13 | 功能描述:IC AMP TRIPLE MUX 1GHZ 32-QFN RoHS:是 类别:集成电路 (IC) >> 线性 - 放大器 - 视频放大器和频缓冲器 系列:- 标准包装:1,000 系列:- 应用:驱动器 输出类型:差分 电路数:3 -3db带宽:350MHz 转换速率:1000 V/µs 电流 - 电源:14.5mA 电流 - 输出 / 通道:60mA 电压 - 电源，单路/双路(±):5 V ~ 12 V，±2.5 V ~ 6 V 安装类型:表面贴装 封装/外壳:20-VFQFN 裸露焊盘 供应商设备封装:20-QFN 裸露焊盘（4x4） 包装:带卷 (TR) |
| ISL59445IRZ-T7 | 功能描述:IC AMP TRIPLE MUX 1GHZ 32-QFN RoHS:是 类别:集成电路 (IC) >> 线性 - 放大器 - 视频放大器和频缓冲器 系列:- 标准包装:1,000 系列:- 应用:驱动器 输出类型:差分 电路数:3 -3db带宽:350MHz 转换速率:1000 V/µs 电流 - 电源:14.5mA 电流 - 输出 / 通道:60mA 电压 - 电源，单路/双路(±):5 V ~ 12 V，±2.5 V ~ 6 V 安装类型:表面贴装 封装/外壳:20-VFQFN 裸露焊盘 供应商设备封装:20-QFN 裸露焊盘（4x4） 包装:带卷 (TR) |
| ISL59446 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:500MHz Triple 4:1 Gain-of-2, Multiplexing Amplifier |
发布紧急采购，3分钟左右您将得到回复。