- 您现在的位置：买卖IC网 > PDF目录10837 > ISL59445IR-T7 (Intersil)IC AMP TRIPLE MUX 1GHZ 32-QFN PDF资料下载
参数资料
| 型号： | ISL59445IR-T7 |
| 厂商： | Intersil |
| 文件页数： | 14/14页 |
| 文件大小： | 0K |
| 描述： | IC AMP TRIPLE MUX 1GHZ 32-QFN |
| 标准包装： | 1,000 |
| 应用： | 4:1 多路复用器-放大器 |
| 电路数： | 3 |
| -3db带宽： | 1GHz |
| 转换速率： | 1200 V/µs |
| 电流 - 电源： | 53mA |
| 电流 - 输出 / 通道： | 130mA |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 32-VFQFN 裸露焊盘 |
| 供应商设备封装： | 32-QFN 裸露焊盘（5x6） |
| 包装： | 带卷 (TR) |
9
FN7456.3
September 30, 2011
Figure 18A illustrates the optimum output load for testing AC
performance. Figure 18B illustrates the optimum output load
when connecting to 50
Ω input terminated equipment.
Application Information
General
The ISL59424, ISL59445 are triple 2:1 and 4:1 muxes that
are ideal for the matrix element of high performance
switchers and routers. The ISL59424, ISL59445 are
optimized to drive a 1.5pF in parallel with a 500
Ω load. The
capacitance can be split between the PCB capacitance an
and external load capacitance. Their low input capacitance
and high input resistance provide excellent 50
Ω or 75Ω
terminations.
Ground Connections
For the best isolation and crosstalk rejection, all GND pins
and NIC pins must connect to the GND plane.
Control Signals
S0, S1, ENABLE, LE, HIZ - These pins are binary coded,
TTL/CMOS compatible control inputs. The S0, S1 pins select
which one of the inputs connect to the output. All three
amplifiers are switched simultaneously from their respective
inputs. The ENABLE, LE, HIZ pins are used to disable the part
to save power, latch in the last logic state and three-state the
output amplifiers, respectively. For control signal rise and fall
times less than 10ns the use of termination resistors close to
the part should be considered to minimize transients coupled
to the output.
Power-Up Considerations
The ESD protection circuits use internal diodes from all pins
the V+ and V- supplies. In addition, a dV/dT- triggered clamp
is connected between the V+ and V- pins, as shown in the
Equivalent Circuits 1 through 4 section of the “Pin
Descriptions” on page 8. The dV/dT triggered clamp
imposes a maximum supply turn-on slew rate of 1V/s.
Damaging currents can flow for power supply rates-of-rise in
excess of 1V/s, such as during hot plugging. Under these
conditions, additional methods should be employed to
ensure the rate of rise is not exceeded.
Consideration must be given to the order in which power is
applied to the V+ and V- pins, as well as analog and logic
input pins. Schottky diodes (Motorola MBR0550T or
equivalent) connected from V+ to ground and V- to ground
(Figure 19) will shunt damaging currents away from the
internal V+ and V- ESD diodes in the event that the V+
supply is applied to the device before the V- supply.
If positive voltages are applied to the logic or analog video
input pins before V+ is applied, current will flow through the
internal ESD diodes to the V+ pin. The presence of large
decoupling capacitors and the loading effect of other circuits
connected to V+, can result in damaging currents through
the ESD diodes and other active circuits within the device.
Therefore, adequate current limiting on the digital and
analog inputs is needed to prevent damage during the time
the voltages on these inputs are more positive than V+.
AC Test Circuits
FIGURE 18A. TEST CIRCUIT WITH OPTIMAL OUTPUT
LOAD
FIGURE 18B. TEST CIRCUIT FOR MEASURING WITH
50Ω OR 75Ω INPUT TERMINATED
EQUIPMENT
FIGURE 18C. BACKLOADED TEST CIRCUIT FOR VIDEO CABLE APPLICATION. BANDWIDTH AND LINEARITY FOR RL
LESS THAN 500Ω WILL BE DEGRADED.
FIGURE 18. TEST CIRCUITS
ISL59424, ISL59445
CL
50Ω
VIN
500Ω
RL
1.5pF
OR
75Ω
ISL59424, ISL59445
RS
CL
VIN
475Ω
TEST
1.5pF
50Ω
OR
75Ω
50Ω
OR
75Ω
50Ω
OR
75Ω
EQUIPMENT
OR
462.5Ω
ISL59424, ISL59445
RS
CL
VIN
50Ω OR 75Ω
TEST
1.5pF
50Ω
OR
75Ω
50Ω
OR
75Ω
EQUIPMENT
ISL59424, ISL59445
相关PDF资料 |
PDF描述 |
|---|---|
| ISL59445IR-T13 | IC AMP TRIPLE MUX 1GHZ 32-QFN |
| ISL59445IR | IC AMP TRIPLE MUX 1GHZ 32-QFN |
| ISL59444IB-T7 | IC CROSSPOINT SW 1GHZ 4X1 16SOIC |
| HR25A-7R-8PA | CONN RCPT 8POS MALE SLD PCB |
| ISL59444IB-T13 | IC CROSSPOINT SW 1GHZ 4X1 16SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL59445IRZ | 功能描述:IC AMP TRIPLE MUX 1GHZ 32-QFN RoHS:是 类别:集成电路 (IC) >> 线性 - 放大器 - 视频放大器和频缓冲器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:50 系列:- 应用:TFT-LCD 面板：VCOM 驱动器 输出类型:满摆幅 电路数:1 -3db带宽:35MHz 转换速率:40 V/µs 电流 - 电源:3.7mA 电流 - 输出 / 通道:1.3A 电压 - 电源，单路/双路(±):9 V ~ 20 V，±4.5 V ~ 10 V 安装类型:表面贴装 封装/外壳:8-TSSOP，8-MSOP（0.118"，3.00mm 宽）裸露焊盘 供应商设备封装:8-uMax-EP 包装:管件 |
| ISL59445IRZ-EVAL | 功能描述:EVAL BOARD FOR ISL59445 RoHS:否 类别:编程器，开发系统 >> 评估演示板和套件 系列:* 标准包装:1 系列:PSoC® 主要目的:电源管理，热管理 嵌入式:- 已用 IC / 零件:- 主要属性:- 次要属性:- 已供物品:板，CD，电源 |
| ISL59445IRZ-T13 | 功能描述:IC AMP TRIPLE MUX 1GHZ 32-QFN RoHS:是 类别:集成电路 (IC) >> 线性 - 放大器 - 视频放大器和频缓冲器 系列:- 标准包装:1,000 系列:- 应用:驱动器 输出类型:差分 电路数:3 -3db带宽:350MHz 转换速率:1000 V/µs 电流 - 电源:14.5mA 电流 - 输出 / 通道:60mA 电压 - 电源，单路/双路(±):5 V ~ 12 V，±2.5 V ~ 6 V 安装类型:表面贴装 封装/外壳:20-VFQFN 裸露焊盘 供应商设备封装:20-QFN 裸露焊盘（4x4） 包装:带卷 (TR) |
| ISL59445IRZ-T7 | 功能描述:IC AMP TRIPLE MUX 1GHZ 32-QFN RoHS:是 类别:集成电路 (IC) >> 线性 - 放大器 - 视频放大器和频缓冲器 系列:- 标准包装:1,000 系列:- 应用:驱动器 输出类型:差分 电路数:3 -3db带宽:350MHz 转换速率:1000 V/µs 电流 - 电源:14.5mA 电流 - 输出 / 通道:60mA 电压 - 电源，单路/双路(±):5 V ~ 12 V，±2.5 V ~ 6 V 安装类型:表面贴装 封装/外壳:20-VFQFN 裸露焊盘 供应商设备封装:20-QFN 裸露焊盘（4x4） 包装:带卷 (TR) |
| ISL59446 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:500MHz Triple 4:1 Gain-of-2, Multiplexing Amplifier |
发布紧急采购，3分钟左右您将得到回复。