参数资料
| 型号： | ISL59448IAZ-T7 |
| 厂商： | Intersil |
| 文件页数： | 5/14页 |
| 文件大小： | 0K |
| 描述： | IC AMP MUX 2:1 500MHZ 24-QSOP |
| 标准包装： | 1,000 |
| 应用： | 2:1 多路复用器-放大器 |
| 电路数： | 3 |
| -3db带宽： | 570MHz |
| 转换速率： | 1600 V/µs |
| 电流 - 电源： | 31mA |
| 电流 - 输出 / 通道： | 180mA |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 24-SSOP（0.154"，3.90mm 宽） |
| 供应商设备封装： | 24-QSOP |
| 包装： | 带卷 (TR) |
13
FN6160.2
March 29, 2006
PC Board Layout
The AC performance of this circuit depends greatly on the
care taken in designing the PC board. The following are
recommendations to achieve optimum high frequency
performance from your PC board.
The use of low inductance components such as chip
resistors and chip capacitors is strongly recommended.
Minimize signal trace lengths. Trace inductance and
capacitance can easily limit circuit performance. Avoid
sharp corners, use rounded corners when possible. Vias
in the signal lines add inductance at high frequency and
should be avoided. PCB traces greater than 1" begin to
exhibit transmission line characteristics with signal rise/fall
times of 1ns or less. High frequency performance may be
degraded for traces greater than one inch, unless strip line
are used.
Match channel-channel analog I/O trace lengths and
layout symmetry. This will minimize propagation delay
mismatches.
Maximize use of AC de-coupled PCB layers. All signal I/O
lines should be routed over continuous ground planes (i.e.
no split planes or PCB gaps under these lines). Avoid vias
in the signal I/O lines.
Use proper value and location of termination resistors.
Termination resistors should be as close to the device as
possible.
When testing use good quality connectors and cables,
matching cable types and keeping cable lengths to a
minimum.
Minimum of 2 power supply de-coupling capacitors are
recommended (1000pF, 0.01F) as close to the devices
as possible - Avoid vias between the cap and the device
because vias add unwanted inductance. Larger caps can
be farther away. When vias are required in a layout, they
should be routed as far away from the device as possible.
The NIC pins are placed on both sides of the input pins.
These pins are not internally connected to the die. It is
recommended these pins be tied to ground to minimize
crosstalk.
ISL59448
相关PDF资料 |
PDF描述 |
|---|---|
| ISL59451IRZ-T7 | IC AMP MUX TRIPLE 4:1 DC 32-QFN |
| ISL59452IRZ-T7 | IC AMP MUX TRIPLE 4:1 DC 32-QFN |
| ISL59481IRZ | IC MUX AMP DUAL 500MHZ 48-QFN |
| ISL59482IRZ | IC MUX AMP DUAL 500MHZ 48-QFN |
| ISL59483IRZ | IC MUX AMP DUAL 500MHZ 48-QFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL59450 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Multiformat Video Crosspoint with Integrated Sync Separator |
| ISL59450IQZ | 功能描述:IC SWITCH VID CRSSPNT 128-MQFP RoHS:是 类别:集成电路 (IC) >> 专用 IC 系列:* 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1 系列:- 类型:调帧器 应用:数据传输 安装类型:表面贴装 封装/外壳:400-BBGA 供应商设备封装:400-PBGA（27x27） 包装:散装 |
| ISL59450IQZ-EVAL | 制造商:Intersil Corporation 功能描述:ISL59450IQZ-EVAL EVALUATION BOARD - Bulk |
| ISL59451 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Triple 4:1 DC Restored Single Supply Video Multiplexing Amplifier |
| ISL59451IRZ | 功能描述:IC AMP TRIPLE MUX 250MHZ 32-QFN RoHS:是 类别:集成电路 (IC) >> 线性 - 放大器 - 视频放大器和频缓冲器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:50 系列:- 应用:TFT-LCD 面板：VCOM 驱动器 输出类型:满摆幅 电路数:1 -3db带宽:35MHz 转换速率:40 V/µs 电流 - 电源:3.7mA 电流 - 输出 / 通道:1.3A 电压 - 电源，单路/双路(±):9 V ~ 20 V，±4.5 V ~ 10 V 安装类型:表面贴装 封装/外壳:8-TSSOP，8-MSOP（0.118"，3.00mm 宽）裸露焊盘 供应商设备封装:8-uMax-EP 包装:管件 |
发布紧急采购，3分钟左右您将得到回复。