- 您现在的位置：买卖IC网 > PDF目录10837 > ISL59830IA-T13 (Intersil)IC VID DRIVER TRUE SGL 16-QSOP PDF资料下载
参数资料
| 型号： | ISL59830IA-T13 |
| 厂商： | Intersil |
| 文件页数： | 5/14页 |
| 文件大小： | 0K |
| 描述： | IC VID DRIVER TRUE SGL 16-QSOP |
| 标准包装： | 2,500 |
| 应用： | 驱动器 |
| 输出类型： | 满摆幅 |
| 电路数： | 3 |
| -3db带宽： | 200MHz |
| 转换速率： | 500 V/µs |
| 电流 - 电源： | 120mA |
| 电流 - 输出 / 通道： | 50mA |
| 电压 - 电源，单路/双路(±)： | 3 V ~ 3.6 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-SSOP（0.154"，3.90mm 宽） |
| 供应商设备封装： | 16-QSOP |
| 包装： | 带卷 (TR) |
13
FN7489.6
May 4, 2006
the EN pin. The applied logic signal is relative to GND pin.
Letting the EN pin float or applying a signal that is less than
0.8V above GND will enable the amplifier. The amplifier will
be disabled when the signal at EN pin is 2V above GND. The
VEE charge pump remains active.
Output Drive Capability
The ISL59830 does not have internal short-circuit protection
circuitry. A short-circuit current of 80mA sourcing and 150mA
sinking for the output is connected to half way between the
rails with a 10
Ω resistor. If the output is shorted indefinitely,
the power dissipation could easily increase such that the part
will be destroyed. Maximum reliability is maintained if the
output current never exceeds ±40mA, after which the
electro-migration limit of the process will be exceeded and
the part will be damaged. This limit is set by the design of the
internal metal interconnections.
Power Dissipation
With the high output drive capability of the ISL59830, it is
possible to exceed the 150°C absolute maximum junction
temperature under certain load current conditions.
Therefore, it is important to calculate the maximum junction
temperature for an application to determine if load conditions
or package types need to be modified to assure operation of
the amplifier in a safe operating area.
The maximum power dissipation allowed in a package is
determined according to:
Where:
TJMAX = Maximum junction temperature
TAMAX = Maximum ambient temperature
ΘJA = Thermal resistance of the package
The maximum power dissipation actually produced by an IC
is the total quiescent supply current times the total power
supply voltage, plus the power in the IC due to the load, or:
for sourcing:
for sinking:
Where:
VS = Supply voltage
ISMAX = Maximum quiescent supply current
VOUT = Maximum output voltage of the application
RLOAD = Load resistance tied to ground
ILOAD = Load current
i = Number of output channels
By setting the two PDMAX equations equal to each other, we
can solve the output current and RLOAD to avoid the device
overheat.
Power Supply Bypassing and Printed Circuit
Board Layout
Strip line design techniques are recommended for the input
and output signal traces. As with any high frequency device,
a good printed circuit board layout is necessary for optimum
performance. Lead lengths should be as short as possible.
The power supply pin must be well bypassed to reduce the
risk of oscillation. For normal single supply operation, where
the VS- pin is connected to the ground plane, a single 4.7F
tantalum capacitor in parallel with a 0.1F ceramic capacitor
from VS+ to GND will suffice. This same capacitor
combination should be placed at each supply pin to ground if
split-internal supplies are to be used. In this case, the VS-
pin becomes the negative supply rail.
For good AC performance, parasitic capacitance should be
kept to a minimum. Use of wire-wound resistors should be
avoided because of their additional series inductance. Use
of sockets should also be avoided if possible. Sockets add
parasitic inductance and capacitance can result in
compromised performance. Minimizing parasitic capacitance
at the amplifier's inverting input pin is also very important.
PD
MAX
T
JMAX
T
AMAX
–
Θ
JA
---------------------------------------------
=
PD
MAX
V
S
I
SMAX
V
S
V
OUTi
–
()
+
×
V
OUT i
R
Li
-----------------
×
=
PD
MAX
V
S
I
SMAX
V
OUTiVS
–
()
+
×
I
LOAD i
×
=
ISL59830
相关PDF资料 |
PDF描述 |
|---|---|
| ISL59445IR-T7 | IC AMP TRIPLE MUX 1GHZ 32-QFN |
| ISL59445IR-T13 | IC AMP TRIPLE MUX 1GHZ 32-QFN |
| ISL59445IR | IC AMP TRIPLE MUX 1GHZ 32-QFN |
| ISL59444IB-T7 | IC CROSSPOINT SW 1GHZ 4X1 16SOIC |
| HR25A-7R-8PA | CONN RCPT 8POS MALE SLD PCB |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL59830IA-T7 | 功能描述:IC VID DRIVER TRUE SGL 16-QSOP RoHS:否 类别:集成电路 (IC) >> 线性 - 放大器 - 视频放大器和频缓冲器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:50 系列:- 应用:TFT-LCD 面板：VCOM 驱动器 输出类型:满摆幅 电路数:1 -3db带宽:35MHz 转换速率:40 V/µs 电流 - 电源:3.7mA 电流 - 输出 / 通道:1.3A 电压 - 电源，单路/双路(±):9 V ~ 20 V，±4.5 V ~ 10 V 安装类型:表面贴装 封装/外壳:8-TSSOP，8-MSOP（0.118"，3.00mm 宽）裸露焊盘 供应商设备封装:8-uMax-EP 包装:管件 |
| ISL59830IAZ | 功能描述:IC DRIVER VIDEO SGL 3.3V 16QSOP RoHS:是 类别:集成电路 (IC) >> 线性 - 放大器 - 视频放大器和频缓冲器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:50 系列:- 应用:TFT-LCD 面板：VCOM 驱动器 输出类型:满摆幅 电路数:1 -3db带宽:35MHz 转换速率:40 V/µs 电流 - 电源:3.7mA 电流 - 输出 / 通道:1.3A 电压 - 电源，单路/双路(±):9 V ~ 20 V，±4.5 V ~ 10 V 安装类型:表面贴装 封装/外壳:8-TSSOP，8-MSOP（0.118"，3.00mm 宽）裸露焊盘 供应商设备封装:8-uMax-EP 包装:管件 |
| ISL59830IAZ-EVAL | 制造商:Intersil Corporation 功能描述:TRUE SGL SUPPLY VID DRVR - Bulk 制造商:Intersil Corporation 功能描述:BOARD EVAL FOR ISL59830 制造商:Intersil 功能描述:ISL90843W LW NOISE LW PWR I2C BUS 256 |
| ISL59830IAZ-T13 | 功能描述:IC VIDEO DRIVER TRUE SGL 16-QSOP RoHS:是 类别:集成电路 (IC) >> 线性 - 放大器 - 视频放大器和频缓冲器 系列:- 标准包装:1,000 系列:- 应用:驱动器 输出类型:差分 电路数:3 -3db带宽:350MHz 转换速率:1000 V/µs 电流 - 电源:14.5mA 电流 - 输出 / 通道:60mA 电压 - 电源，单路/双路(±):5 V ~ 12 V，±2.5 V ~ 6 V 安装类型:表面贴装 封装/外壳:20-VFQFN 裸露焊盘 供应商设备封装:20-QFN 裸露焊盘（4x4） 包装:带卷 (TR) |
| ISL59830IAZ-T7 | 功能描述:IC VIDEO DRIVER TRUE SGL 16-QSOP RoHS:是 类别:集成电路 (IC) >> 线性 - 放大器 - 视频放大器和频缓冲器 系列:- 标准包装:1,000 系列:- 应用:驱动器 输出类型:差分 电路数:3 -3db带宽:350MHz 转换速率:1000 V/µs 电流 - 电源:14.5mA 电流 - 输出 / 通道:60mA 电压 - 电源，单路/双路(±):5 V ~ 12 V，±2.5 V ~ 6 V 安装类型:表面贴装 封装/外壳:20-VFQFN 裸露焊盘 供应商设备封装:20-QFN 裸露焊盘（4x4） 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。