- 您现在的位置：买卖IC网 > PDF目录383139 > ISL6111 (Intersil Corporation) Current Regulated PCI Hot Plug Power Switch Controller PDF资料下载
参数资料
| 型号： | ISL6111 |
| 厂商： | Intersil Corporation |
| 英文描述： | Current Regulated PCI Hot Plug Power Switch Controller |
| 中文描述： | 电流调节的PCI热插拔电源开关控制器 |
| 文件页数： | 12/16页 |
| 文件大小： | 480K |
| 代理商： | ISL6111 |
12
Using the ISL6111EVAL2 Platform
Biasing and General Information
The ISL6111EVAL2 platform (Figure 20) allows a designer to
evaluate and modify the performance and functionality of the
ISL6111 in a simple environment. The board is made such
that the heat dissipating resistors are shielded from users and
equipment by being placed on the bottom, despite this the top
of the load board still gets hot.
Test point names correspond to the ISL6111 device (U1) pins.
Along with the ISL6111 on the ISL6111EVAL2 platform are 2
N-Channel power MOSFETs, (Q1- Q2) these are used as the
external switches for the +5V and +3.3V supplies to the load.
Current sensing is facilitated by the two 5m
1W metal strip
resistors (R7, R3), the voltages developed across the sense
resistors are compared to references on board the ISL6111.
The ISL6111EVAL2 platform is powered through the 5 labeled
jacks on the left half of the board, with outputs on the right
half. After properly biasing the ISL6111, signal the ENABLE
input high (>2.4V), this will turn on the FET switches and
apply voltage to the loads resistors and capacitors.
Voltage and current measurements can be easily made as
the test points facilitate access to IC pins and other critical
circuit nodes.
Evaluating Current Regulation Duration
The current regulation (CR) duration is set by the CRTIM
capacitor value, C3 to ground. This provides a programmable
duration during which the ISL6111 holds the programmed CR
level. Once this duration has expired and the ISL6111 is still in
CR mode the output voltages will turn off.
The intent of any protection device is to quickly isolate the
voltage supplies so a faulty load card does not drag down a
supply. A duration period too lengthy increases the likelihood
of FET switch damage and results in slower isolation of the
faulty card from the rest of system.
Figures 14 -19 show nominal turn-on, turn-on into OC
condition with CR mode waveforms.
FIGURE 12. CRSET CURRENT vs TEMPERATURE
FIGURE 13. CRTIM THRESHOLD VOLTAGE vs
TEMPERATURE
Typical Performance Curves & Waveforms
(Continued)
101
100
99
98
97
I
TEMPERATURE (°C)
0
25
50
75
85
2.74
2.72
2.70
2.68
TEMPERATURE (°C)
C
0
25
50
75
85
ISL6111
相关PDF资料 |
PDF描述 |
|---|---|
| ISL6111CRZA | Current Regulated PCI Hot Plug Power Switch Controller |
| ISL6111EVAL2 | Current Regulated PCI Hot Plug Power Switch Controller |
| ISL6117 | Octal Transparent D-Type Latches With 3-State Outputs 20-SO -40 to 85 |
| ISL6116CB | Power Distribution Controllers |
| ISL6116CBZA-T | Power Distribution Controllers |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL6111CR | 功能描述:IC CTRLR HOT PLUG SWITCH 20-QFN RoHS:否 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 产品培训模块:Obsolescence Mitigation Program 标准包装:100 系列:- 类型:热插拔开关 应用:通用 内部开关:是 电流限制:可调 电源电压:9 V ~ 13.2 V 工作温度:-40°C ~ 150°C 安装类型:表面贴装 封装/外壳:10-WFDFN 裸露焊盘 供应商设备封装:10-TDFN-EP（3x3） 包装:管件 |
| ISL6111CR-T | 功能描述:IC CTRLR HOT PLUG SWITCH 20-QFN RoHS:否 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 产品培训模块:Obsolescence Mitigation Program 标准包装:100 系列:- 类型:热插拔开关 应用:通用 内部开关:是 电流限制:可调 电源电压:9 V ~ 13.2 V 工作温度:-40°C ~ 150°C 安装类型:表面贴装 封装/外壳:10-WFDFN 裸露焊盘 供应商设备封装:10-TDFN-EP（3x3） 包装:管件 |
| ISL6111CRZA | 功能描述:热插拔功率分布 W/ANNEAL 20LD MLFP 5X5 PCI HOTSWAP CNTR RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube |
| ISL6111CRZA-T | 功能描述:热插拔功率分布 W/ANNEAL 20LD MLFP 5X5 PCI HOTSWAP CNTR RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube |
| ISL6111EVAL2 | 功能描述:EVALUATION BOARD 2 FOR ISL6111 RoHS:否 类别:编程器，开发系统 >> 评估演示板和套件 系列:- 标准包装:1 系列:PCI Express® (PCIe) 主要目的:接口，收发器，PCI Express 嵌入式:- 已用 IC / 零件:DS80PCI800 主要属性:- 次要属性:- 已供物品:板 |
发布紧急采购，3分钟左右您将得到回复。