- 您现在的位置：买卖IC网 > PDF目录383139 > ISL6115CB-T (INTERSIL CORP) Power Distribution Controllers PDF资料下载
参数资料
| 型号： | ISL6115CB-T |
| 厂商： | INTERSIL CORP |
| 元件分类： | 电源管理 |
| 英文描述： | Power Distribution Controllers |
| 中文描述： | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO8 |
| 封装： | PLASTIC, MS-012AA, SOIC-8 |
| 文件页数： | 5/12页 |
| 文件大小： | 363K |
| 代理商： | ISL6115CB-T |
5
Description and Operation
The members of this family are single power supply
distribution controllers for generic hot swap applications
across the +2.5V to +12V supply range. The ISL6115 is
targeted for +12V switching applications whereas the
ISL6116 is targeted for +5V, the ISL6117 for +3.3V and the
ISL6120 for +2.5V applications. Each IC has a hardwired
undervoltage (UV) threshold level approximately 17% lower
than the stated voltages.
These ICs feature a highly accurate programmable
overcurrent (OC) detecting comparator, programmable
current regulation (CR) with programmable time delay to
latch off, and programmable soft start turn-on ramp all set
with a minimum of external passive components. The ICs
also include severe OC protection that immediately shuts
down the MOSFET switch should a rapid load current
transient such as a near dead short cause the CR Vth to
exceed the programmed level by 150mV. Additionally, the
ICs have a UV indicator and an OC latch indicator. The
functionality of the PGOOD feature is enabled once the IC is
biased, monitoring and reporting any UV condition on the
ISEN pin.
Upon initial power up, the IC can either isolate the voltage
supply from the load by holding the external N-Channel
MOSFET switch off or apply the supply rail voltage directly to
the load for true hot swap capability.
The PWRON pin must
be pulled low for the device to isolate the power supply from
the load by holding the external N-channel MOSFET off.
With the PWRON pin held high or floating the IC will be in
true hot swap mode. In both cases the IC turns on in a soft
start mode protecting the supply rail from sudden in-rush
current.
At turn-on, the external gate capacitor of the N-Channel
MOSFET is charged with a 10
μ
A current source resulting in
a programmable ramp (soft start turn-on). The internal
ISL6115 charge pump supplies the gate drive for the 12V
supply switch driving that gate to ~V
DD
+5V, for the other
three ICs the gate drive voltage is limited to the chip bias
voltage, VDD.
Load current passes through the external current sense
resistor. When the voltage across the sense resistor exceeds
the user programmed CR voltage threshold value, (see Table 1
for R
ISET
programming resistor value and resulting nominal
current regulation threshold voltage, V
CR
) the controller enters
its current regulation mode. At this time, the time-out capacitor,
on C
TIM
pin is charged with a 20
μ
A current source and the
controller enters the current limit time to latch-off period. The
length of the current limit time to latch-off duration is set by the
value of a single external capacitor (see Table 2 for CTIM
capacitor value and resulting nominal current limited time out
to latch-off duration) placed from the CTIM pin (pin 6) to
ground. The programmed current level is held until either the
OC event passes or the time out period expires. If the former
is the case then the N-Channel MOSFET is fully enhanced
and the C
TIM
capacitor is discharged. Once CTIM charges to
1.87V, signaling that the time out period has expired an
internal latch is set whereby the FET gate is quickly pulled to
0V turning off the N-Channel MOSFET switch, isolating the
faulty load.
This IC responds to a severe overcurrent load (defined as a
voltage across the sense resistor >150mV over the OC Vth set
point) by immediately driving the N-Channel MOSFET gate to
0V in about 10
μ
s. The gate voltage is then slowly ramped up
turning on the N-Channel MOSFET to the programmed current
regulation level; this is the start of the time out period.
Upon a UV condition the PGOOD signal will pull low when
tied high through a resistor to the logic or VDD supply. This
pin is a UV fault indicator. For an OC latch off indication,
monitor CTIM, pin 6. This pin will rise rapidly from 1.9V to
VDD once the time out period expires.
See Figures 12 to 16 for waveforms relevant to text.
The IC is reset after an OC latch-off condition by a low level
on the PWRON pin and is turned on by the PWRON pin
being driven high.
Application Considerations
During the soft start and the time-out delay duration with the
IC in its current limit mode, the V
GS
of the external N-Channel
MOSFET is reduced driving the MOSFET switch into a (linear
region) high r
DS(ON)
state. Strike a balance between the CR
limit and the timing requirements to avoid periods when the
external N-Channel MOSFETs may be damaged or destroyed
due to excessive internal power dissipation. Refer to the
MOSFET SOA
information in the manufacturer’s data sheet.
When driving particularly large capacitive loads a longer soft
start time to prevent current regulation upon charging and a
short CR time may offer the best application solution relative
to reliability and FET MTF.
Physical layout of R
SENSE
resistor
is critical to avoid the
possibility of false overcurrent occurrences. Ideally, trace
routing between the R
SENSE
resistors and the IC is as direct
TABLE 1.
R
ISET
RESISTOR
10k
4.99k
2.5k
750
NOTE: Nominal Vth = R
ISET
x 20
μ
A.
NOMINAL OC VTH
200mV
100mV
50mV
15mV
TABLE 2.
C
TIM
CAPACITOR
0.022
μ
F
0.047
μ
F
0.1
μ
F
NOTE: Nominal time-out period = C
TIM
x 93k
.
NOMINAL CURRENT LIMITED PERIOD
2ms
4.4ms
9.3ms
ISL6115, ISL6116, ISL6117, ISL6120
相关PDF资料 |
PDF描述 |
|---|---|
| ISL6115CBZA | Power Distribution Controllers |
| ISL6115CBZA-T | Power Distribution Controllers |
| ISL6116CB-T | Power Distribution Controllers |
| ISL6116CBZA | Power Distribution Controllers |
| ISL6117CB-T | Power Distribution Controllers |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL6115CBZA | 功能描述:IC CTRLR POWER DISTRIB 8-SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:119 系列:- 类型:热交换控制器 应用:通用型，PCI Express? 内部开关:无 电流限制:- 电源电压:3.3V，12V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:80-TQFP 供应商设备封装:80-TQFP（12x12） 包装:托盘 产品目录页面:1423 (CN2011-ZH PDF) |
| ISL6115CBZA-T | 功能描述:IC CTRLR POWER DISTRIB 8-SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 产品培训模块:Obsolescence Mitigation Program 标准包装:100 系列:- 类型:热插拔开关 应用:通用 内部开关:是 电流限制:可调 电源电压:9 V ~ 13.2 V 工作温度:-40°C ~ 150°C 安装类型:表面贴装 封装/外壳:10-WFDFN 裸露焊盘 供应商设备封装:10-TDFN-EP（3x3） 包装:管件 |
| ISL6115CBZA-TS2490 | 制造商:Intersil Corporation 功能描述:IBM, ISL6115CBZA-T W/CONTAINER LABELING - Tape and Reel 制造商:Intersil 功能描述:IBM, ISL6115CBZA-T W/CONTAINER LABELING |
| ISL6115CBZA-TS2490S | 制造商:Intersil Corporation 功能描述: |
| ISL6115EVAL1 | 功能描述:EVALUATION BOARD 12V ISL6115 RoHS:否 类别:编程器，开发系统 >> 过时/停产零件编号 系列:- 标准包装:1 系列:- 传感器类型:CMOS 成像，彩色（RGB） 传感范围:WVGA 接口:I²C 灵敏度:60 fps 电源电压:5.7 V ~ 6.3 V 嵌入式:否 已供物品:成像器板 已用 IC / 零件:KAC-00401 相关产品:4H2099-ND - SENSOR IMAGE WVGA COLOR 48-PQFP4H2094-ND - SENSOR IMAGE WVGA MONO 48-PQFP |
发布紧急采购，3分钟左右您将得到回复。