- 您现在的位置：买卖IC网 > PDF目录19824 > ISL6119LIBZA (Intersil)IC CTRLR PWR SUPP USB DUAL 8SOIC PDF资料下载
参数资料
| 型号： | ISL6119LIBZA |
| 厂商： | Intersil |
| 文件页数： | 12/13页 |
| 文件大小： | 0K |
| 描述： | IC CTRLR PWR SUPP USB DUAL 8SOIC |
| 标准包装： | 980 |
| 类型： | 热交换开关 |
| 应用： | USB |
| 内部开关： | 是 |
| 电流限制： | 1A |
| 电源电压： | 2.7 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 8-SOICN |
| 包装： | 管件 |
ISL6119
Implementing Autoreset on the ISL6119
Hot Swap Controller
Description of Operation
Abstract
In applications where the cost, complexity or requirement for
a system controller is avoided and an autonomous power
control function is desired, a device that can monitor and
protect against excessive current failures is needed. This
tech brief shows how to implement such an autonomous
controller using the ISL6119HIB. This application works only
with the ‘H’ version of this device. The ‘H’ version refers to
the enable function being asserted upon a high input.
Rpu = 2K
C = 0.1μF
VIN
FLTn
ISL6119H
ENABLE
GND
FIGURE 21.
Introduction
The ISL6118, ISL6119 and ISL6121 are all 2.5V to 5V power
supply controllers, each having a different level of current
regulation (CR). The ISL6118 and ISL6119 have 2
independent controllers with CR levels of 0.6A and 1.0A
respectively whereas the ISL6121 is a single supply
controller with a 2A CR level. Each of these devices features
integrated power switch(es) for power control. Each switch is
driven by a constant current source giving a controlled ramp
up of the output voltage. This provides a soft start turn-on
eliminating bus voltage drooping caused by in-rush current
while charging heavy load capacitances. The independent
enabling inputs and fault reporting outputs for each channel
are available and necessary for the autonomous autoreset
application.
The undervoltage (UV) feature prevents turn-on of the
outputs unless the ENABLE pin and VIN are > 2.5V. During
initial turn-on the ISL6119 prevents fault reporting by
blanking the fault signal. Rising and falling outputs are
current-limited voltage ramps so that both the inrush current
and voltage slew rate are limited, independent of load. This
reduces supply droop due to surge and eliminates the need
Initially as voltage is applied to VIN, the pull up resistor (Rpu)
provides for pull up to VIN on both the ENABLE pin asserting
the output once VIN > 2.5V and on the FLTn pin. Once
turned on and an overcurrent (OC) condition occurs the IC
provides CR protection for 10ms and then the FLTn pin pulls
low through Rpu and also pulling the ENABLE low thus
resetting the device fault condition. At this time the Rpu
charges the cap and the voltage on the ENABLE/FLTn node
rises until the ENABLE > 2.0 and the output is asserted on
once again. This automatic reset cycle will continue until the
OC fault no longer exists on the output. After several
seconds in this mode of operation the IC thermal protection
invokes adjusting the timing of the on-off cycle to prevent
excessive thermal dissipation in the power switch protecting
itself and surrounding circuitry. See Figure 22 for operation
waveform.
.
VIN/FLTn 5V/DIV
VOUT 2V/DIV
for external EMI filters. During operation, once an OC
condition is detected the appropriate output is current limited
to the appropriate level for 10ms to allow transient conditions
to pass. If still in current limit after the current limit period has
elapsed, the output is latched off and the fault is reported by
pulling the corresponding FAULT low. The FAULT signal is
0V
0A
IOUT 0.5A/DIV
4ms/DIV
latched low until reset by the ENABLE signal being de-
asserted at which time the FAULT signal will clear.
It is this described sequence of events that allows for the
autoreset function to be implemented in a cost efficient
manner requiring the addition of only an RC network per
channel to the typical application.
Figure 21 illustrates the RC network needed with suggested
component values and the configuration of the relevant pins
for each autoreset channel.
12
FIGURE 22. AUTO RESET OPERATION
Applications
? USB
? 2.5V to 5V up to 10W power port protection
相关PDF资料 |
PDF描述 |
|---|---|
| LCMXO1200E-3M132C | IC PLD 1200LUTS 101I/O 132-BGA |
| GSA50DRMH | CONN EDGECARD 100POS .125 SQ WW |
| GMA50DRMH | CONN EDGECARD 100POS .125 SQ WW |
| GCM21A7U2E152JX01D | CAP CER 1500PF 250V 5% U2J 0805 |
| MAX5023LASA+T | IC REG LDO 5V .15A 8-SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL6119LIBZA-T | 功能描述:电源开关 IC - USB W/ANNEAL DL USB HI SIDESWTICH ENABLE LW RoHS:否 制造商:Micrel 电源电压-最小:2.7 V 电源电压-最大:5.5 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:SOIC-8 封装:Tube |
| ISL6119LIBZA-TS2715 | 制造商:Intersil Corporation 功能描述:BROADCOM, ISL6119LIBZA-T W/BUSINESS TRACKING REQUIREMENTS, S - Tape and Reel |
| ISL6119USBEVAL1 | 功能描述:EVALUATION BOARD FOR ISL6119 RoHS:否 类别:编程器，开发系统 >> 评估演示板和套件 系列:- 标准包装:1 系列:PCI Express® (PCIe) 主要目的:接口，收发器，PCI Express 嵌入式:- 已用 IC / 零件:DS80PCI800 主要属性:- 次要属性:- 已供物品:板 |
| ISL6119USBEVAL1-T | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:USB Dual Port Power Supply Controller |
| ISL6120 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Power Distribution Controllers |
发布紧急采购，3分钟左右您将得到回复。