- 您现在的位置：买卖IC网 > PDF目录16197 > ISL613XSUPEREVAL2 (Intersil)EVAL BOARD ISL613X SUPERVISOR PDF资料下载
参数资料
| 型号： | ISL613XSUPEREVAL2 |
| 厂商： | Intersil |
| 文件页数： | 7/15页 |
| 文件大小： | 0K |
| 描述： | EVAL BOARD ISL613X SUPERVISOR |
| 标准包装： | 1 |
| 主要目的： | 电源管理，电源监控器/跟踪器/序列发生器 |
| 已用 IC / 零件： | ISL6131，6132 |
| 已供物品： | 板 |
ISL6131, ISL6132
Applications Usage
Using the ISL6131EVAL1Z and
ISL6132EVAL1Z Platforms
The ISL6131EVAL1Z platform is set up to monitor and report an
undervoltage condition on each of 12V, 5V, 3.3V and 1.2V
supplies to a -20% tolerance.
Each monitored supply has an individual STATUS output and an
AND’ed PGOOD output signal for all four supplies. An OFF LED is
the PGOOD indicator for all four supplies. The ENABLE input
enables or disables the voltage monitoring function. See Figures
10 to 17 for performance and function examples.
The ISL6132EVAL1Z platform is set up to monitor and report
either an undervoltage or an overvoltage condition on 5V and
12V supplies to a ±10% tolerance. There is an OV and a UV
STATUS output for each of the two supplies and individual
AND’ed PGOOD outputs when each voltage is within the
VIN
EN
VIN
EN
VIN
EN
ABC
STATUS
PGOOD
VOUT
DC-DC_A
VOUT
DC-DC_B
VOUT
DC-DC_C
VMON_A
VMON_D
programmed voltage range. An OFF LED indicates compliance to
the voltage range upper and lower limits.
The ENABLE inputs enable or disable the voltage monitoring
functions for each monitor supply.
See Figures 18 to 24 for performance and function examples.
VDD
ENABLE
ISL6131 VMON_C
VMON_B
GND
Figures 25 and 26 illustrate the ISL6131EVAL1Z and
ISL6132EVAL1Z platforms respectively in image and schematic.
Using the ISL6131, ISL6132 for Negative
Voltage Monitoring Applications
The ISL6131, ISL6132 can be used for -V monitoring because it
monitors any voltage that is more positive relative to its GND pin.
With correct bias differential, these parts can monitor any
voltage, regardless of polarity or amplitude.
Using the ISL6131 for “Lossless” Sequencing
Applications
The ISL6131 can be used in a “lossless” sequencing application
in which a monitored output voltage determines the start of the
next sequenced turn-on. As shown in Figure 7, VMON_A input
looks at the common V IN of several DC-DC converters and
enables DC-DC_A with STATUS _A, once both V IN and ENABLE are
satisfied. VMON_B monitors the output of DC-DC_A, and when
the acceptable output voltage is reached, DC-DC_B is enabled
with STATUS_B output. This sequencing pattern continues until
all DC-DC outputs are on, at which time PGOOD signal is
released. A delay of 160ms from VMON > V VMONVth to STATUS
high ensures stability at each step prior to subsequent turn-on.
Additional ISL6131s can be employed in parallel to sequence any
number of DC-DC convertors in this fashion.
7
FIGURE 7. ISL6131 “LOSSLESS” SEQUENCING CONFIGURATION
Using the ISL6131 for System Voltage and
Over-Temperature Monitoring
As a multi-voltage monitoring IC, the ISL6131 can monitor
over-temperature as well as voltage for more complete coverage
of system stability. Using a Negative Temperature Coefficient
(NTC) passive device in place of one of the resistors in a VMON
divider provides over-temperature monitoring either locally or
remotely.
Evaluations of this application configuration have involved the
QT0805T-202J, QT0805Y-502J and QT0805Y-103J NTCs from
Quality Thermistor.
ISL6131 over-temperature monitoring is not as accurate as
specific temperature monitor ICs, but this implementation
provides a cost-efficient solution with 5% tolerances achievable.
See Figures 8 and 9 for over-temperature sensing configuration
and operation results. In this example, the desired maximum
temperature is 100°C. The QT0805Y-103J NTC was placed at the
end of 3 feet of twisted pair wire to emulate a remote sensing
application. According to the Quality Thermistor data sheet, this
NTC device has a +25°C value of 10K and a +100°C value of
0.923K. An accompanying standard value resistor of 3.83K was
chosen for the divider so that at 100°C, VMON ~0.633V with the
bias voltage at 3.3V.
The resulting falling VMON trip point with the configuration
shown is ~0.634V, with ~0.642V for rising, which equates to
~95°C for under-temperature and ~97°C for over-temperature,
respectively. Choosing the standard resistor value above and
below R1 allows for small adjustments in the temperature trip
point.
FN9119.6
February 11, 2014
相关PDF资料 |
PDF描述 |
|---|---|
| ISL612XSEQEVAL1 | EVALUATION BOARD FOR ISL612XSEQ |
| NBSG14BAEVB | BOARD EVALUATION BBG NBSG14BA |
| NBSG11BAEVB | BOARD EVALUATION BBG NBSG11BA |
| DC-VIDEO-TVP5146N | VIDEO DAUGHTER CARD |
| X90100EVAL | EVALUATION BOARD DIGITAL CAPACIT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL6140 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Negative Voltage Hot Plug Controller |
| ISL6140/41EVAL1 | 功能描述:EVALUATION BOARD NEG ISL6140/41 RoHS:否 类别:编程器，开发系统 >> 过时/停产零件编号 系列:- 标准包装:1 系列:- 传感器类型:CMOS 成像，彩色（RGB） 传感范围:WVGA 接口:I²C 灵敏度:60 fps 电源电压:5.7 V ~ 6.3 V 嵌入式:否 已供物品:成像器板 已用 IC / 零件:KAC-00401 相关产品:4H2099-ND - SENSOR IMAGE WVGA COLOR 48-PQFP4H2094-ND - SENSOR IMAGE WVGA MONO 48-PQFP |
| ISL6140/41EVAL1Z | 功能描述:EVAL BOARD 1 FOR ISL6140/41 RoHS:是 类别:编程器，开发系统 >> 评估演示板和套件 系列:* 标准包装:1 系列:PCI Express® (PCIe) 主要目的:接口，收发器，PCI Express 嵌入式:- 已用 IC / 零件:DS80PCI800 主要属性:- 次要属性:- 已供物品:板 |
| ISL6140CB | 功能描述:IC CONTROLLER HOT PLUG 8-SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 产品培训模块:Obsolescence Mitigation Program 标准包装:100 系列:- 类型:热插拔开关 应用:通用 内部开关:是 电流限制:可调 电源电压:9 V ~ 13.2 V 工作温度:-40°C ~ 150°C 安装类型:表面贴装 封装/外壳:10-WFDFN 裸露焊盘 供应商设备封装:10-TDFN-EP（3x3） 包装:管件 |
| ISL6140CB-T | 功能描述:IC CTRLR HOT PLUG NEG VOLT 8SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 产品培训模块:Obsolescence Mitigation Program 标准包装:100 系列:- 类型:热插拔开关 应用:通用 内部开关:是 电流限制:可调 电源电压:9 V ~ 13.2 V 工作温度:-40°C ~ 150°C 安装类型:表面贴装 封装/外壳:10-WFDFN 裸露焊盘 供应商设备封装:10-TDFN-EP（3x3） 包装:管件 |
发布紧急采购，3分钟左右您将得到回复。