- 您现在的位置：买卖IC网 > PDF目录20677 > ISL6209CBZ-T (Intersil)IC MOSFET DRVR SYNC BUCK 8-SOIC PDF资料下载
参数资料
| 型号： | ISL6209CBZ-T |
| 厂商： | Intersil |
| 文件页数： | 8/10页 |
| 文件大小： | 0K |
| 描述： | IC MOSFET DRVR SYNC BUCK 8-SOIC |
| 标准包装： | 2,500 |
| 配置： | 高端和低端，同步 |
| 输入类型： | PWM |
| 延迟时间： | 20ns |
| 电流 - 峰： | 2A |
| 配置数： | 1 |
| 输出数： | 2 |
| 高端电压 - 最大（自引导启动）： | 33V |
| 电源电压： | 4.5 V ~ 5.5 V |
| 工作温度： | -10°C ~ 100°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 8-SOIC |
| 包装： | 带卷 (TR) |
ISL6209
A good layout would help reduce the ringing on the phase
and gatenodes significantly:
1. Avoid using vias for decoupling components where
possible, especially in the BOOT-to-PHASE path. Little or
no use of vias for VCC and GND is also recommended.
Decoupling loops should be short.
2. All power traces (UGATE, PHASE, LGATE, GND, VCC)
should be short and wide, and avoid using vias. If vias
must be used, two or more vias per layer transition is
recommended.
3. Keep the SOURCE of the upper FET as close as
thermally possible to the DRAIN of the lower FET.
4. Keep the connection in between the SOURCE of lower
FET and power ground wide and short.
5. Input capacitors should be placed as close to the DRAIN
of the upper FET and the SOURCE of the lower FET as
thermally possible.
NOTE: Refer to Intersil Tech Brief TB447 for more information.
Thermal Management
For maximum thermal performance in high current, high
switching frequency applications, connecting the thermal
pad of the QFN part to the power ground with multiple vias,
or placing a low noise copper plane underneath the SOIC
part is recommended. This heat spreading allows the part to
achieve its full thermal potential.
Suppressing MOSFET Gate Leakage
With VCC at ground potential, UGATE and LGATE are high
impedance. In this state, any stray leakage has the potential
to deliver charge to either gate. If UGATE receives sufficient
charge to bias the device on (Note: Internal circuitry prevents
leakage currents from charging above 1.8V), a low
impedance path will be connected between the MOSFET
drain and PHASE. If the input power supply is present and
active, the system could see potentially damaging currents.
Worst-case leakage currents are on the order of pico-amps;
therefore, a 10k Ω resistor, connected from UGATE to
PHASE, is more than sufficient to bleed off any stray leakage
current. This resistor will not affect the normal performance
of the driver or reduce its efficiency.
8
相关PDF资料 |
PDF描述 |
|---|---|
| 572D686X06R3S2T | CAP TANT 68UF 6.3V 20% 1206 |
| VI-JNZ-CX-B1 | CONVERTER MOD DC/DC 2V 30W |
| VE-J6L-CX-F2 | CONVERTER MOD DC/DC 28V 75W |
| T95S474K035HSAL | CAP TANT 0.47UF 35V 10% 1507 |
| VE-J6L-CX-F1 | CONVERTER MOD DC/DC 28V 75W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL6209CR | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| ISL6209CR-T | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:High Voltage Synchronous Rectified Buck MOSFET Driver |
| ISL6209CRZ | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:High Voltage Synchronous Rectified Buck MOSFET Driver |
| ISL6209CRZ-T | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:High Voltage Synchronous Rectified Buck MOSFET Driver |
| ISL6210 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Dual Synchronous Rectified MOSFET Drivers |
发布紧急采购，3分钟左右您将得到回复。