参数资料
| 型号： | ISL6217CV |
| 厂商： | Intersil |
| 文件页数： | 7/19页 |
| 文件大小： | 0K |
| 描述： | IC CTRLR PWM INTEL PENT 38-TSSOP |
| 标准包装： | 50 |
| 应用： | 控制器，Intel Pentium? IMVP-IV，IMVP+ |
| 输入电压： | 5.5 V ~ 25 V |
| 输出数： | 1 |
| 工作温度： | -10°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 38-TFSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 38-TSSOP |
| 包装： | 管件 |
ISL6217
Functional Pin Description
COMP - This pin provides connection to the error amplifier
output.
VDD
1
38 VBAT
FB - This pin is connected to the inverting input of the error
DACOUT 2
37 ISEN1
amplifier.
DSV
3
36 PHASE1
EA+ - This pin is connected to the non-inverting input of the
FSET 4
PWRCH 5
35 UG1
34 BOOT1
error amplifier and is used for setting the “Droop” voltage.
STV - The voltage on this pin sets the initial start-up or
EN
6
33 VSSP1
“Boot” voltage.
DRSEN 7
DSEN# 8
VID0 9
32 LG1
31 VDDP
30 LG2
SOFT - This pin programs the slew rate of VID changes,
Deep Sleep and Deeper Sleep transitions and soft-start
after initializing. This pin is connected to ground via a
VID1 10
VID2 11
VID3 12
VID4 13
VID5 14
PGOOD 15
EA+ 16
COMP 17
FB 18
SOFT 19
ISL6217
TSSOP
29 VSSP2
28 BOOT2
27 UG2
26 PHASE2
25 ISEN2
24 VSEN
23 DRSV
22 STV
21 OCSET
20 VSS
capacitor, and to EA+ through an external “Droop” resistor.
DSEN# - This pin connects to system logic “STP_CPU#”
and enables Deep Sleep mode of operation. Deep Sleep is
enabled when a logic LOW signal is detected on this pin.
DRSEN - This pin connects to system logic “DPRSLPVR”
and enables Deeper Sleep mode of operation when a logic
HIGH is detected on this pin.
VBAT - Voltage on this pin provides feed-forward battery
information which adjusts the oscillator ramp amplitude.
FSET - A resistor from this pin to ground programs the
switching frequency.
VDD - This pin is used to connect +5V to the IC to supply
all power necessary to operate the chip. The IC starts to
operate when the voltage on this pin exceeds the rising
POR threshold and shuts down when the voltage on this
pin drops below the falling POR threshold.
VDDP - This pin provides a low-esr bypass connection to
the internal gate drivers for the +5V source.
PGOOD - This pin is used as an input and an output and is
tied to the Vccp and Vcc_mch PGOOD signals. During
start-up, this pin is recognized as an input and prevents
further slewing of the output voltage from the “Boot” level
until PGOOD from Vccp and Vcc_mch is enabled High.
After start-up, this pin has an open drain output used to
indicate the status of the CORE output voltage. This pin is
pulled low when the system output is outside of the
regulation limits. PGOOD includes a timer for power-on
delay.
EN - This pin is connected to the system signal VR_ON
and provides the enable/disable function for the PWM
controller.
PWRCH - This pin selects the number of power channels.
A HIGH logic level on this pin enables 2 channel operation,
and a LOW logic signal enables single channel operation.
OCSET - A resistor from this pin to ground sets the
overcurrent protection threshold.
VSEN - This pin is used for remote sensing of the
microprocessor CORE voltage.
7
ISEN1, ISEN2 - These pins are used as current sense
inputs from the individual converter channel phase nodes.
DACOUT - This pin provides access to the output of the
Digital-to-Analog Converter.
DSV - The voltage on this pin provides the setpoint for
output voltage during Deep Sleep Mode of operation.
DRSV – The voltage on this pin provides the setpoint for
output voltage during Deeper Sleep Mode of operation.
VID0, VID1, VID2, VID3, VID4, VID5 - These pins are used
as inputs to the 6-bit Digital-to-Analog converter (DAC).
VID0 is the least significant bit and VID5 is the most
significant bit.
UG1, UG2 - These pins are the gate-drive outputs to the
high side MOSFETs for channels 1 and 2, respectively.
LG1, LG2 - These pins are the gate-drive outputs to the
low side MOSFETs for channels 1 and 2, respectively.
BOOT1, BOOT2 - These pins are connected to the
bootstrap capacitors, for upper gate-drive, for channels 1
and 2, respectively.
PHASE1, PHASE2 - These pins are connected to the
phase nodes of channels 1 and 2, respectively.
VSSP1, VSSP2 - These pins are connected to the power
ground of channels 1 and 2, respectively.
VSS - This pin provides connection for signal ground.
相关PDF资料 |
PDF描述 |
|---|---|
| X5043S8I-2.7T1 | IC SUPERVISOR CPU 4K EE 8-SOIC |
| X5043S8I-2.7AT1 | IC SUPERVISOR CPU 4K EE 8-SOIC |
| X5043S8-2.7T2 | IC SUPERVISOR CPU 4K EE 8-SOIC |
| GMM43DTKT | CONN EDGECARD 86POS DIP .156 SLD |
| ESM36DREF | CONN EDGECARD 72POS .156 EYELET |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL6217CV-T | 功能描述:IC CTRLR PWM INTEL PENT 38-TSSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,000 系列:- 应用:电源，ICERA E400，E450 输入电压:4.1 V ~ 5.5 V 输出数:10 输出电压:可编程 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:42-WFBGA，WLCSP 供应商设备封装:42-WLP 包装:带卷 (TR) |
| ISL6217CVZ | 功能描述:IC CTRLR PWM INTEL PENT 38-TSSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 标准包装:43 系列:- 应用:控制器，Intel VR11 输入电压:5 V ~ 12 V 输出数:1 输出电压:0.5 V ~ 1.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-VFQFN 裸露焊盘 供应商设备封装:48-QFN（7x7） 包装:管件 |
| ISL6217CVZA | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Precision Multi-Phase Buck PWM Precision Multi-Phase Buck PWM Positioning IMVP-IV? and IMVP-IV+ |
| ISL6217CVZA-T | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Precision Multi-Phase Buck PWM Precision Multi-Phase Buck PWM Positioning IMVP-IV? and IMVP-IV+ |
| ISL6217CVZ-T | 功能描述:IC CTRLR PWM INTEL PENT 38-TSSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 标准包装:43 系列:- 应用:控制器，Intel VR11 输入电压:5 V ~ 12 V 输出数:1 输出电压:0.5 V ~ 1.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-VFQFN 裸露焊盘 供应商设备封装:48-QFN（7x7） 包装:管件 |
发布紧急采购，3分钟左右您将得到回复。