- 您现在的位置：买卖IC网 > PDF目录13165 > ISL6227CAZ-T (Intersil)IC CONTROLLER DDR, DDR2 28QSOP PDF资料下载
参数资料
| 型号： | ISL6227CAZ-T |
| 厂商： | Intersil |
| 文件页数： | 15/27页 |
| 文件大小： | 0K |
| 描述： | IC CONTROLLER DDR, DDR2 28QSOP |
| 标准包装： | 1 |
| 应用： | 控制器，DDR，DDR2 |
| 输入电压： | 5 V ~ 28 V |
| 输出数： | 2 |
| 输出电压： | 0.9 V ~ 5.5 V |
| 工作温度： | -10°C ~ 100°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-SSOP（0.154"，3.90mm 宽） |
| 供应商设备封装： | 28-SSOP/QSOP |
| 包装： | 标准包装 |
| 其它名称： | ISL6227CAZ-TDKR |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页当前第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页
ISL6227
Output Voltage Program
The output voltage of either channel is set by a resistive divider
from the output to ground. The center point of the divider is
connected to the VSEN pin as shown in Figure 34. The
output voltage value is determined by Equation 3:
The two channels can be programmed to operate in different
modes depending on the VOUTx connection and the load
current. Once both channels operate in the PWM mode,
however, they will be synchronized to the 300kHz switching
clock. The 180° phase shift reduces the noise couplings
V O = ----------------------------------------------
0.9V ? ( R1 + R2 )
R2
(EQ. 3)
between the two channels and reduces the input current ripple.
The critical discontinuous conduction current value for the
PWM to HYS mode switch-over can be calculated by
where 0.9V is the value of the internal reference. The VSEN
Equation 4:
2 ? F SW ? L O ? V IN
pin voltage is also used by the controller for the power good
function and to detect undervoltage and overvoltage
conditions.
( V IN – V O ) ? V O
I HYS = ----------------------------------------------------
(EQ. 4)
Q1
V IN
The HYS mode to PWM switch-over current I HYS1 is
determined by the activation time of the HYS mode
controller. It is affected by the ESR, the inductor value, the
UGATE
ISEN
R CS
L1
V O
input and output voltage.
The HYS mode control can improve converter efficiency with
LGATE
Q2
C1
C Z
R1
reduced switching frequency. The efficiency is further
improved by the diode emulation scheme in discontinuous
conduction mode. The diode emulation scheme does not
VOUT
VSEN
allow the inductor sink current from the output capacitor,
thereby reducing the circulating energy. It is achieved by
sensing the free-wheeling current going through the
ISL6227
OCSET
R OC
R2
synchronous MOSFET through Phase node voltage polarity
change after the upper MOSFET is turned off. Before the
current reverses direction, the lower MOSFET gate pulses
are terminated.
FIGURE 34. OUTPUT VOLTAGE PROGRAM
Operation Mode Control
VOUTx pin programs the two channels of ISL6227 in two
different operational modes:
1. If VOUTx is connected to ground, the channel will be put
into a fixed switching frequency of 300kHz CCM, also
known as forced PWM mode regardless of load
conditions.
2. If the VOUTx is connected to the output voltage, the
channel will operate in either fixed 300kHz PWM mode or
HYS mode, depending on the load conditions. It operates
in the PWM mode when the load current exceeds the
critical discontinuous conduction value, otherwise it will
operate in a HYS mode, as shown in the following table.
The PWM-HYS and HYS-PWM switch-over is provided
automatically by the mode control circuit, which constantly
monitors the inductor current through phase voltage polarity,
and alters the way the gate driver pulse signal is generated.
Mode Transition
For a buck regulator, if the load current is higher than critical
value I HYS1 , the voltage drop on the synchronous MOSFET
in the free-wheeling period is always negative, and vice
versa. The mode control circuit monitors the phase node
voltage in the off-period. The polarity of this voltage is used
as the criteria for whether the load current is greater than the
critical value, and thus determines whether the converter will
operate in PWM or HYS mode.
To prevent chatter between operating modes, the circuit
looks for eight sequentially matching polarity signals before it
VOUT PIN
GND
Connects to output voltage
Connects to output voltage
INDUCTOR
CURRENT
Any value
≤ I HYS
>I HYS1
OPERATION
MODE
Forced PWM
HYS
PWM
decides to perform a mode change. The algorithm is true for
both CCM-HYS and HYS-CCM transitions.
In the HYS mode, the PWM comparator and the error
amplifier, that provided control in the CCM mode, are put in a
clamped stage and the hysteretic comparator is activated. A
change is also made to the gate logic. The synchronous
MOSFET is controlled in diode emulation fashion, hence the
current in the synchronous MOSFET will be kept in one
direction only. Figures 35 and 36 illustrate the mode change
by counting eight switching cycles.
15
FN9094.7
May 4, 2009
相关PDF资料 |
PDF描述 |
|---|---|
| VI-B1R-EV-B1 | CONVERTER MOD DC/DC 7.5V 150W |
| UCW1C151MCL1GS | CAP ALUM 150UF 16V 20% SMD |
| RMM12DRKH-S13 | CONN EDGECARD 24POS .156 EXTEND |
| RBB66DHFR-S578 | EDGECARD 132POS .050 SMD W/POSTS |
| VI-J1R-CX | CONVERTER MINIMOD DC/DC 7.5V 75W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL6227CAZ-TS2698 | 功能描述:IC CONTROLLER DDR, DDR2 28QSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 标准包装:43 系列:- 应用:控制器，Intel VR11 输入电压:5 V ~ 12 V 输出数:1 输出电压:0.5 V ~ 1.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-VFQFN 裸露焊盘 供应商设备封装:48-QFN（7x7） 包装:管件 |
| ISL6227EVAL1 | 功能描述:EVALUATION BOARD 1 ISL6227 RoHS:否 类别:编程器，开发系统 >> 过时/停产零件编号 系列:- 标准包装:1 系列:- 传感器类型:CMOS 成像，彩色（RGB） 传感范围:WVGA 接口:I²C 灵敏度:60 fps 电源电压:5.7 V ~ 6.3 V 嵌入式:否 已供物品:成像器板 已用 IC / 零件:KAC-00401 相关产品:4H2099-ND - SENSOR IMAGE WVGA COLOR 48-PQFP4H2094-ND - SENSOR IMAGE WVGA MONO 48-PQFP |
| ISL6227EVAL2 | 功能描述:EVALUATION BOARD 2 ISL6227 RoHS:否 类别:编程器，开发系统 >> 过时/停产零件编号 系列:- 标准包装:1 系列:- 传感器类型:CMOS 成像，彩色（RGB） 传感范围:WVGA 接口:I²C 灵敏度:60 fps 电源电压:5.7 V ~ 6.3 V 嵌入式:否 已供物品:成像器板 已用 IC / 零件:KAC-00401 相关产品:4H2099-ND - SENSOR IMAGE WVGA COLOR 48-PQFP4H2094-ND - SENSOR IMAGE WVGA MONO 48-PQFP |
| ISL6227EVAL2Z | 功能描述:EVAL BOARD ISL6227 RoHS:是 类别:编程器，开发系统 >> 过时/停产零件编号 系列:- 标准包装:1 系列:- 传感器类型:CMOS 成像，彩色（RGB） 传感范围:WVGA 接口:I²C 灵敏度:60 fps 电源电压:5.7 V ~ 6.3 V 嵌入式:否 已供物品:成像器板 已用 IC / 零件:KAC-00401 相关产品:4H2099-ND - SENSOR IMAGE WVGA COLOR 48-PQFP4H2094-ND - SENSOR IMAGE WVGA MONO 48-PQFP |
| ISL6227HRZ | 功能描述:IC CONTROLLER DDR, DDR2 28QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 标准包装:43 系列:- 应用:控制器，Intel VR11 输入电压:5 V ~ 12 V 输出数:1 输出电压:0.5 V ~ 1.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-VFQFN 裸露焊盘 供应商设备封装:48-QFN（7x7） 包装:管件 |
发布紧急采购，3分钟左右您将得到回复。