参数资料
| 型号： | ISL6227IAZ |
| 厂商： | Intersil |
| 文件页数： | 20/27页 |
| 文件大小： | 0K |
| 描述： | IC CONTROLLER DDR, DDR2 28QSOP |
| 标准包装： | 480 |
| 应用： | 控制器，DDR，DDR2 |
| 输入电压： | 5 V ~ 28 V |
| 输出数： | 2 |
| 输出电压： | 0.9 V ~ 5.5 V |
| 工作温度： | -40°C ~ 100°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-SSOP（0.154"，3.90mm 宽） |
| 供应商设备封装： | 28-SSOP/QSOP |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页当前第20页第21页第22页第23页第24页第25页第26页第27页
ISL6227
regulation, the OVP comparator is disengaged. The
MOSFET driver will restore its normal operation. When the
OVP occurs, the PGOOD will drop to low as well.
This OVP scheme provides a ‘soft’ crowbar function, which
helps clamp the voltage overshoot, and does not invert the
output voltage when otherwise activated with a continuously
high output from lower MOSFET driver - a common problem
for OVP schemes with a latch.
DDR Application
High throughput Double Data Rate (DDR) memory ICs are
replacing traditional memory ICs in the latest generation of
Notebook PCs and in other computing devices. A novel
feature associated with this type of memory are the
referencing and data bus termination techniques. These
techniques employ a reference voltage, VREF, that tracks
the center point of VDDQ and VSS voltages, and an
additional VTT power source where all terminating resistors
are connected. Despite the additional power source, the
overall memory power consumption is reduced compared to
traditional termination.
The added power source has a cluster of requirements that
should be observed and considered. Due to the reduced
differential thresholds of DDR memory, the termination
power supply voltage, VTT, closely tracks VDDQ/2 voltage.
Another very important feature of the termination power
supply is the capability to operate at equal efficiency in
sourcing and sinking modes. The VTT supply regulates the
output voltage with the same degree of precision when
current is flowing from the supply to the load, and when the
current is diverted back from the load into the power supply.
The ISL6227 dual channel PWM controller possesses
several important enhancements that allow re-configuration
for DDR memory applications, and provides all three
voltages required in a DDR memory compliant computer.
To reconfigure the ISL6227 for a complete DDR solution, the
DDR pin should be set high permanently to the VCC rail.
This activates some functions inside the chip that are
specific to DDR memory power needs.
In the DDR application presented in Figure 32, the first
controller regulates the VDDQ rail to 2.5V. The output
voltage is set by external dividers Rfb1 and Rfb12. The
second controller regulates the VTT rail to VDDQ/2. The
OCSET2 pin function is now different, and serves as an
For the VTT channel where output is derived from the VDDQ
output, some control and protective functions have been
significantly simplified. For example, the overcurrent, and
overvoltage, and undervoltage protections for the second
channel controller are disabled when the DDR pin is set
high. The hysteretic mode of operation is also disabled on
the VTT channel to allow sinking capability to be
independent from the load level. As the VTT channel tracks
the VDDQ/2 voltage, the soft-start function is not required,
and the SOFT2 pin may be left open, in the event both
channels are enabled simultaneously. However, if the VTT
channel is enabled later than the VDDQ, the SOFT2 pin
must have a capacitor in place to ensure soft-start. In case of
overcurrent or undervoltage caused by short circuit on VTT,
the fault current will propagate to the first channel and shut
down the converter.
The VREF voltage will be present even if the VTT is
disabled.
Channel Synchronization in DDR Applications
The presence of two PWM controllers on the same die
requires channel synchronization, to reduce inter-channel
interference that may cause the duty factor jitter and
increased output ripple.
The PWM controller is at greatest noise susceptibility when
an error signal on the input of the PWM comparator
approaches the decision making point. False triggering may
occur, causing jitter and affecting the output regulation.
A common approach used to synchronize dual channel
converters is out-of-phase operation. Out-of-phase
operation reduces input current ripple and provides a
minimum interference for channels that control different
voltage levels.
When the DDR pin is connected to GND for dual switcher
applications, the channels operate 180° out-of-phase. When
used in a DDR application with cascaded converters (VTT
generated from VDDQ), several methods of synchronization
are implemented in the ISL6227. In the DDR mode, when
the DDR pin is connected to VCC, the channels operate
either with 0° phase shift, when the VIN pin is connected to
the GND, or with 90° phase shift if the VIN pin is connected
to a voltage higher than 4.2V.
The following table lists the different synchronization
schemes and their usage:
input that brings VDDQ/2 voltage, created by the Rd1 and
Rd2 divider, inside the chip, effectively providing a tracking
function for the VTT voltage.
The PG2 pin function is also different in DDR mode. This pin
becomes the output of the buffer, whose input is connected
DDR PIN
0
1
1
VIN PIN
VIN pin >4.2V
VIN pin voltage <4.2V
VIN pin voltage >4.2V
SYNCHRONIZATION
180° out of phase
0° phase
90° phase shift
to the center point of the R/R divider from the VDDQ output
by the OCSET2 pin. The buffer output voltage serves as a
1.25V reference for the DDR memory chips. Current
capability of this pin is 10mA (12mA max).
20
FN9094.7
May 4, 2009
相关PDF资料 |
PDF描述 |
|---|---|
| UPS2C330MHD1TO | CAP ALUM 33UF 160V 20% RADIAL |
| HBM44DRYN-S13 | CONN EDGECARD 88POS .156 EXTEND |
| X40020S14I-AT1 | IC VOLTAGE MONITOR DUAL 14-SOIC |
| ISL6225CAZA | IC CTRLR DDR DRAM, SDRAM 28QSOP |
| 2256-12L | POWER CHOKE 8.2UH MOLDED AXIAL |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL6227IAZ-T | 功能描述:IC CONTROLLER DDR, DDR2 28QSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 标准包装:43 系列:- 应用:控制器，Intel VR11 输入电压:5 V ~ 12 V 输出数:1 输出电压:0.5 V ~ 1.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-VFQFN 裸露焊盘 供应商设备封装:48-QFN（7x7） 包装:管件 |
| ISL6227IRZ | 功能描述:IC CONTROLLER DDR, DDR2 28QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 标准包装:43 系列:- 应用:控制器，Intel VR11 输入电压:5 V ~ 12 V 输出数:1 输出电压:0.5 V ~ 1.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-VFQFN 裸露焊盘 供应商设备封装:48-QFN（7x7） 包装:管件 |
| ISL6227IRZ-T | 功能描述:IC CONTROLLER DDR, DDR2 28QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 标准包装:43 系列:- 应用:控制器，Intel VR11 输入电压:5 V ~ 12 V 输出数:1 输出电压:0.5 V ~ 1.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-VFQFN 裸露焊盘 供应商设备封装:48-QFN（7x7） 包装:管件 |
| ISL6228 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:High-Performance Dual-Output Buck Controller for Notebook Applications |
| ISL6228EVAL3Z | 功能描述:EVALUATION BOARD FOR ISL6228 RoHS:是 类别:编程器，开发系统 >> 评估板 - DC/DC 与 AC/DC（离线）SMPS 系列:Robust Ripple Regulator™ (R³) 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:True Shutdown™ 主要目的:DC/DC，步升 输出及类型:1，非隔离 功率 - 输出:- 输出电压:- 电流 - 输出:1A 输入电压:2.5 V ~ 5.5 V 稳压器拓扑结构:升压 频率 - 开关:3MHz 板类型:完全填充 已供物品:板 已用 IC / 零件:MAX8969 |
发布紧急采购，3分钟左右您将得到回复。