参数资料
| 型号： | ISL6236IRZA-TR5281 |
| 厂商： | Intersil |
| 文件页数： | 26/35页 |
| 文件大小： | 0K |
| 描述： | IC MAIN PWR CTRLR QUAD 32-QFN |
| 标准包装： | 6,000 |
| 应用： | 控制器，笔记本电脑电源系统 |
| 输入电压： | 5.5 V ~ 25 V |
| 输出数： | 4 |
| 输出电压： | 多重 |
| 工作温度： | -40°C ~ 100°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 32-VFQFN 裸露焊盘 |
| 供应商设备封装： | 32-QFN 裸露焊盘（5x5） |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页当前第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页
ISL6236
Detection
ON-TIME (t ON ) ON)
full-load efficiency (assuming that the coil resistance remains
fixed) and less output voltage ripple. Penalties for using
higher inductor values include larger physical size and
degraded load-transient response (especially at low
input-voltage levels).
DC output accuracy specifications refer to the trip level of the
error comparator. When the inductor is in continuous
conduction, the output voltage has a DC regulation higher
than the trip level by 50% of the ripple. In discontinuous
conduction (SKIP = GND, light load), the output voltage has
a DC regulation higher than the trip level by approximately
1.0% due to slope compensation.
Forced-PWM Mode
The low-noise, forced-PWM (SKIP = VCC) mode disables
the zero-crossing comparator, which controls the low-side
switch ON-time. Disabling the zero-crossing detector causes
the low-side, gate-drive waveform to become the
complement of the high-side, gate-drive waveform. The
inductor current reverses at light loads as the PWM loop
strives to maintain a duty ratio of V OUT /V IN . The benefit of
forced-PWM mode is to keep the switching frequency fairly
constant, but it comes at a cost: the no-load battery current
can be 10mA to 50mA, depending on switching frequency
and the external MOSFETs.
Forced-PWM mode is most useful for reducing
audio-frequency noise, improving load-transient response,
providing sink-current capability for dynamic output voltage
adjustment, and improving the cross-regulation of
multiple-output applications that use a flyback transformer or
coupled inductor.
Enhanced Ultrasonic Mode
(25kHz (min) Pulse Skipping)
Leaving SKIP unconnected or connecting SKIP to REF
activates a unique pulse-skipping mode with a minimum
switching frequency of 25kHz. This ultrasonic pulse-skipping
mode eliminates audio-frequency modulation that would
otherwise be present when a lightly loaded controller
automatically skips pulses. In ultrasonic mode, the controller
automatically transitions to fixed-frequency PWM operation
when the load reaches the same critical conduction point
(ILOAD(SKIP)).
An ultrasonic pulse occurs when the controller detects that
no switching has occurred within the last 20μs. Once
triggered, the ultrasonic controller pulls LGATE high, turning
on the low-side MOSFET to induce a negative inductor
current. After FB drops below the regulation point, the
controller turns off the low-side MOSFET (LGATE pulled low)
and triggers a constant ON-time (UGATE driven high). When
the ON-time has expired, the controller re-enables the
low-side MOSFET until the controller detects that the
inductor current dropped below the zero-crossing threshold.
Starting with a LGATE pulse greatly reduces the peak output
26
voltage when compared to starting with a UGATE pulse, as
long as VFB < VREF, LGATE is off and UGATE is on, similar
to pure SKIP mode.
40μs (MAX)
INDUCTOR
CURRENT
Zero-Crossing
ZERO-CROSSING
DETECTION
0A
FB<Reg.Point
FB<REG.POINT
)
FIGURE 72. ULTRASONIC CURRENT WAVEFORMS
Reference and Linear Regulators (VREF3,
REF, LDO and 14V Charge Pump)
The 3.3V reference (VREF3) is accurate to ±1.5%
over-temperature, making VREF3 useful as a precision
system reference. VREF3 can supply up to 5mA for external
loads. Bypass VREF3 to GND with a 0.01μF capacitor.
Leave it open if there is no load.
The 2V reference (REF) is accurate to ±1% over-temperature,
also making REF useful as a precision system reference.
Bypass REF to GND with a 0.1μF (min) capacitor. REF can
supply up to 50μA for external loads.
An internal regulator produces a fixed 5V
(LDOREFIN < 0.2V) or 3.3V (LDOREFIN > VCC - 1V). In an
adjustable mode, the LDO output can be set from 0.7V to
4.5V. The LDO output voltage is equal to two times the
LDOREFIN voltage. The LDO regulator can supply up to
100mA for external loads. Bypass LDO with a minimum
4.7μF ceramic capacitor. When the LDOREFIN < 0.2V and
BYP voltage is 5V, the LDO bootstrap-switchover to an
internal 0.7 Ω P-Channel MOSFET switch connects BYP to
LDO pin while simultaneously shutting down the internal
linear regulator. These actions bootstrap the device,
powering the loads from the BYP input voltages, rather than
through internal linear regulators from the battery. Similarly,
when the BYP = 3.3V and LDOREFIN = VCC, the LDO
bootstrap-switchover to an internal 1.5 Ω P-Channel
MOSFET switch connects BYP to LDO pin while
simultaneously shutting down the internal linear regulator.
No switchover action in adjustable mode.
In Figure 68, the external 14V charge pump is driven by
LGATE1. When LGATE1 is low, D1a charged C8 sourced
from OUT1. C8 voltage is equal to OUT1 minus a diode
drop. When LGATE1 transitions to high, the charges from C8
will transfer to C 12 through D1b and charge it to VLGATE1
FN6373.6
April 29, 2010
相关PDF资料 |
PDF描述 |
|---|---|
| ESA18DTKS | CONN EDGECARD 36POS DIP .125 SLD |
| ISL6524ACBZA-T | IC CTRLR VRM8.5 PWM TRPL 28-SOIC |
| RBB85DHHN | CONN EDGE DUAL .050 DIP 170 POS |
| ISL6524ACBZ-T | IC CTRLR VRM8.5 PWM TRPL 28-SOIC |
| EMA18DTKS | CONN EDGECARD 36POS DIP .125 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL6236IRZA-TR5453 | 制造商:Intersil Corporation 功能描述:STD. ISL6236IRZA-TR5281 (A03 MASK) W/GOLD BOND WIRE ONLY - Tape and Reel |
| ISL6237 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:High-Efficiency, Quad-Output, Main Power Supply Controllers for Notebook Computers |
| ISL6237EVAL1 | 制造商:Intersil Corporation 功能描述:ISL6237 EVAL BOARD 1 - QFN - Bulk |
| ISL6237IRZ | 功能描述:热插拔功率分布 ISL6237 QD CNTRLR IMVP-6 32LD MLFP 5X5 RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube |
| ISL6237IRZ-T | 功能描述:热插拔功率分布 ISL6237 QD CNTRLR IMVP-6 32LD MLFP 5X5 RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。