- 您现在的位置：买卖IC网 > PDF目录16715 > ISL62383CHRTZ (Intersil)IC PWR SUPPLY CONTROLLER 28TQFN PDF资料下载
参数资料
| 型号： | ISL62383CHRTZ |
| 厂商： | Intersil |
| 文件页数： | 19/23页 |
| 文件大小： | 0K |
| 描述： | IC PWR SUPPLY CONTROLLER 28TQFN |
| 标准包装： | 75 |
| 应用： | 电源控制器 |
| 输入电压： | 5.5 V ~ 25 V |
| 电源电压： | 5.5 V ~ 25 V |
| 电流 - 电源： | 150µA |
| 工作温度： | -10°C ~ 100°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-WFQFN 裸露焊盘 |
| 供应商设备封装： | 28-TQFN（4x4） |
| 包装： | 管件 |
ISL62381, ISL62382, ISL62383, ISL62381C, ISL62382C, ISL62383C
Δ V C = -------------------------------
I PP
8 ? C O ? F SW
(EQ. 21)
0.6
If the output of the converter has to support a load with high
pulsating current, several capacitors will need to be paralleled
0.48
to reduce the total ESR until the required V P-P is achieved.
The inductance of the capacitor can cause a brief voltage dip
if the load transient has an extremely high slew rate. Low
inductance capacitors should be considered in this scenario.
A capacitor dissipates heat as a function of RMS current and
frequency. Be sure that I P-P is shared by a sufficient quantity
of paralleled capacitors so that they operate below the
0.36
0.24
0.12
k=1
k = 0.75
k = 0.5
k = 0.25
k=0
maximum rated RMS current at F SW . Take into account that
the rated value of a capacitor can fade as much as 50% as
the DC voltage across it increases.
0
0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
1.0
Selection of the Input Capacitor
The important parameters for the bulk input capacitance are
the voltage rating and the RMS current rating. For reliable
operation, select bulk capacitors with voltage and current
ratings above the maximum input voltage and capable of
supplying the RMS current required by the switching circuit.
Their voltage rating should be at least 1.25 times greater
than the maximum input voltage, while a voltage rating of 1.5
times is a preferred rating. Figure 28 is a graph of the input
capacitor RMS ripple current, normalized relative to output
load current, as a function of duty cycle and is adjusted for
converter efficiency. The normalized RMS ripple current
calculation is written as Equation 22:
DUTY CYCLE
FIGURE 28. NORMALIZED RMS INPUT CURRENT @ EFF = 1
MOSFET Selection and Considerations
Typically, a MOSFET cannot tolerate even brief excursions
beyond their maximum drain to source voltage rating. The
MOSFETs used in the power stage of the converter should
have a maximum V DS rating that exceeds the sum of the
upper voltage tolerance of the input power source and the
voltage spike that occurs when the MOSFET switches off.
There are several power MOSFETs readily available that are
optimized for DC/DC converter applications. The preferred
high-side MOSFET emphasizes low gate charge so that the
device spends the least amount of time dissipating power in
I C ( RMS , NORMALIZED ) =
D ? k
I MAX
IN
Where:
2
12
I MAX ? D ? ( 1 – D ) + --------------
-----------------------------------------------------------------------
(EQ. 22)
the linear region. Unlike the low-side MOSFET which has the
drain-source voltage clamped by its body diode during turn
off, the high-side MOSFET turns off with a V DS of
approximately V IN - V OUT , plus the spike across it. The
preferred low-side MOSFET emphasizes low r DS(ON) when
fully saturated to minimize conduction loss. It should be
V OUT
V IN ? EFF
P CON_LS ≈ I LOAD ? r DS ( ON ) _LS ? ( 1 – D )
- I MAX is the maximum continuous I LOAD of the converter
- k is a multiplier (0 to 1) corresponding to the inductor
peak-to-peak ripple amplitude expressed as a
percentage of I MAX (0% to 100%)
- D is the duty cycle that is adjusted to take into account
the efficiency of the converter which is written as:
D = --------------------------
(EQ. 23)
In addition to the bulk capacitance, some low ESL ceramic
capacitance is recommended to decouple between the drain
of the high-side MOSFET and the source of the low-side
MOSFET.
noted that this is an optimal configuration of MOSFET
selection for low duty cycle applications (D < 50%). For
higher output, low input voltage solutions, a more balanced
MOSFET selection for high- and low-side devices may be
warranted.
For the low-side (LS) MOSFET, the power loss can be
assumed to be conductive only and is written as Equation 24:
2
(EQ. 24)
For the high-side (HS) MOSFET, the its conduction loss is
written as Equation 25:
P CON_HS = I LOAD
2
?
r DS ( ON ) _HS ? D
(EQ. 25)
For the high-side MOSFET, the switching loss is written as
Equation 26:
V IN ? I VALLEY ? t ON ? f SW V IN ? I PEAK ? t OFF ? f SW
2 2
P SW_HS = ----------------------------------------------------------------- + -------------------------------------------------------------
(EQ. 26)
19
FN6665.5
May 13, 2011
相关PDF资料 |
PDF描述 |
|---|---|
| RBM06DRMT-S288 | CONN EDGECARD 12POS .156 EXTEND |
| GMM12DTKN-S288 | CONN EDGECARD 24POS .156 EXTEND |
| V72B3V3E100BL2 | CONVERTER MOD DC/DC 3.3V 100W |
| REC5-123.3DRW/H6/A | CONV DC/DC 5W 9-18VIN +/-3.3VOUT |
| GMM12DTKH-S288 | CONN EDGECARD 24POS .156 EXTEND |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL62383CHRTZ-T | 功能描述:IC PWR SUPPLY CONTROLLER 28TQFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电源控制器，监视器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 应用:多相控制器 输入电压:- 电源电压:9 V ~ 14 V 电流 - 电源:- 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:40-WFQFN 裸露焊盘 供应商设备封装:40-TQFN-EP（5x5） 包装:带卷 (TR) |
| ISL62383HIEVAL1Z | 功能描述:EVALUATION BOARD FOR ISL62383HI RoHS:是 类别:编程器，开发系统 >> 评估板 - DC/DC 与 AC/DC（离线）SMPS 系列:Robust Ripple Regulator™ (R³) 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:True Shutdown™ 主要目的:DC/DC，步升 输出及类型:1，非隔离 功率 - 输出:- 输出电压:- 电流 - 输出:1A 输入电压:2.5 V ~ 5.5 V 稳压器拓扑结构:升压 频率 - 开关:3MHz 板类型:完全填充 已供物品:板 已用 IC / 零件:MAX8969 |
| ISL62383HRTZ | 功能描述:IC PWR SUPPLY CONTROLLER 28TQFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电源控制器，监视器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 应用:多相控制器 输入电压:- 电源电压:9 V ~ 14 V 电流 - 电源:- 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:40-WFQFN 裸露焊盘 供应商设备封装:40-TQFN-EP（5x5） 包装:带卷 (TR) |
| ISL62383HRTZ-T | 功能描述:IC PWR SUPPLY CONTROLLER 28TQFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电源控制器，监视器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 应用:多相控制器 输入电压:- 电源电压:9 V ~ 14 V 电流 - 电源:- 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:40-WFQFN 裸露焊盘 供应商设备封装:40-TQFN-EP（5x5） 包装:带卷 (TR) |
| ISL62383LOEVAL1Z | 功能描述:EVALUATION BOARD FOR ISL62383LO RoHS:是 类别:编程器，开发系统 >> 评估板 - DC/DC 与 AC/DC（离线）SMPS 系列:Robust Ripple Regulator™ (R³) 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:True Shutdown™ 主要目的:DC/DC，步升 输出及类型:1，非隔离 功率 - 输出:- 输出电压:- 电流 - 输出:1A 输入电压:2.5 V ~ 5.5 V 稳压器拓扑结构:升压 频率 - 开关:3MHz 板类型:完全填充 已供物品:板 已用 IC / 零件:MAX8969 |
发布紧急采购，3分钟左右您将得到回复。