- 您现在的位置：买卖IC网 > PDF目录15165 > ISL6244CRZ (Intersil)IC REG CTRLR BUCK PWM 32-QFN PDF资料下载
参数资料
| 型号： | ISL6244CRZ |
| 厂商： | Intersil |
| 文件页数： | 12/25页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR BUCK PWM 32-QFN |
| 标准包装： | 60 |
| PWM 型： | 电流/电压模式 |
| 输出数： | 4 |
| 频率 - 最大： | 4MHz |
| 占空比： | 75% |
| 电源电压： | 4.75 V ~ 5.25 V |
| 降压： | 是 |
| 升压： | 无 |
| 回扫： | 无 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | 0°C ~ 70°C |
| 封装/外壳： | 32-VFQFN 裸露焊盘 |
| 包装： | 管件 |
ISL6244
V COMP
+
+
A digital to analog converter (DAC) generates a reference
voltage based on the state of logic signals at pins VID4
-
-
PWM1
through VID0. The DAC decodes a 5-bit logic signal (VID)
into one of the discrete voltages shown in Table 1. Each VID
f(j ω )
SAWTOOTH SIGNAL
input offers a 20 μ A pull-up to an internal 2.5V source for use
I ER
+
-
I AVG
÷ N
Σ
I 4 *
I 3 *
I 2
with open-drain outputs. External pull-up resistors or active-
high output stages can augment the pull-up current sources,
but a slight accuracy error can occur if they are pulled above
2.9V. The DAC-selected reference voltage is connected to
the non-inverting input of the error amplifier.
I 1
NOTE: *Channels 3 and 4 are optional.
FIGURE 16. CHANNEL-1 PWM FUNCTION AND CURRENT-
BALANCE ADJUSTMENT
The ISL6244 features a second non-inverting input to the
error amplifier which allows the user to directly offset the
DAC reference voltage in the positive direction only. The
offset voltage is created by an internal current source which
feeds out the OFS pin into a user selected external resistor
to ground.
Two considerations designers face are MOSFET selection
and inductor design. Both are significantly improved when
EXTERNAL CIRCUIT
ISL6244 INTERNAL CIRCUIT
channel currents track at any load level. The need for
complex drive schemes for multiple MOSFETs, exotic
magnetic materials, and expensive heat sinks is avoided,
R C
C C
COMP
ERROR AMPLIFIER
+
+
resulting in a cost-effective and easy to implement solution
relative to single-phase conversion. Channel-current
balance insures the thermal advantage of multi-phase
conversion is realized. Heat dissipation is spread over
multiple channels and a greater area than single phase
approaches.
R FB
+
V DROOP
-
FB
IOUT
-
I AVG
REFERENCE
VOLTAGE
V COMP
Voltage Regulation
VDIFF
The output of the error amplifier, V COMP , is compared to the
sawtooth waveform to modulate the pulse width of the PWM
signals. The PWM signals control the timing of the Intersil
MOSFET drivers and regulate the converter output to the
specified reference voltage. Three distinct inputs to the error
amplifier determine the voltage level of V COMP . The internal
and external circuitry which control voltage regulation is
REMOTE
SENSE
POINTS
V OUT
GND
VSEN
RGND
+
-
DIFFERENTIAL
REMOTE-SENSE
AMPLIFIER
illustrated in Figure 17.
Most multi-phase controllers simply have the output voltage
fed back to the inverting input of the error amplifier through a
R OFS
+
V OFS
-
OFS
1/5
100 μ A
OFFSET
VOLTAGE
resistor. The ISL6244 features an internal differential
remote-sense amplifier in the feedback path. The amplifier
removes the voltage error encountered when measuring the
output voltage relative to the local controller ground
reference point, resulting in a more accurate means of
sensing output voltage. Connect the microprocessor sense
pins to the non-inverting input, VSEN, and inverting input,
RGND, of the remote-sense amplifier. The remote-sense
amplifier output, V DIFF , is then tied through an external
resistor to the inverting input of the error amplifier.
12
FIGURE 17. OUTPUT-VOLTAGE AND LOAD-LINE
REGULATION
The resulting voltage across the resistor, V OFS , is internally
divided down by five to create the offset voltage. This
method of offsetting the DAC voltage is more accurate than
external methods of level-shifting the FB pin.
FN9106.3
December 28, 2004
相关PDF资料 |
PDF描述 |
|---|---|
| CAT1022ZI-25-GT3 | IC SUPERVISOR CPU 2K EEPR 8MSOP |
| ECM25DTBD-S189 | CONN EDGECARD 50POS R/A .156 SLD |
| SN471M025ST | CAP ALUM 470UF 25V 20% RADIAL |
| ISL6307BIRZ-T | IC REG CTRLR BUCK PWM VM 48-QFN |
| GCC61DCMH-S288 | CONN EDGECARD 122POS .100 EXTEND |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL6244CRZ-T | 功能描述:电流型 PWM 控制器 VER OF ISL6244CR-T RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| ISL6244EVAL1 | 功能描述:EVALUATION BOARD ISL6244 RoHS:否 类别:编程器，开发系统 >> 评估板 - DC/DC 与 AC/DC（离线）SMPS 系列:- 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:True Shutdown™ 主要目的:DC/DC，步升 输出及类型:1，非隔离 功率 - 输出:- 输出电压:- 电流 - 输出:1A 输入电压:2.5 V ~ 5.5 V 稳压器拓扑结构:升压 频率 - 开关:3MHz 板类型:完全填充 已供物品:板 已用 IC / 零件:MAX8969 |
| ISL6244HR | 功能描述:IC REG CTRLR BUCK PWM 32-QFN RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:4,000 系列:- PWM 型:电压模式 输出数:1 频率 - 最大:1.5MHz 占空比:66.7% 电源电压:4.75 V ~ 5.25 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 85°C 封装/外壳:40-VFQFN 裸露焊盘 包装:带卷 (TR) |
| ISL6244HR-T | 功能描述:IC REG CTRLR BUCK PWM 32-QFN RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:4,000 系列:- PWM 型:电压模式 输出数:1 频率 - 最大:1.5MHz 占空比:66.7% 电源电压:4.75 V ~ 5.25 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 85°C 封装/外壳:40-VFQFN 裸露焊盘 包装:带卷 (TR) |
| ISL6244HRZ | 功能描述:电流型 PWM 控制器 VER OF ISL6244HR RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
发布紧急采购，3分钟左右您将得到回复。