参数资料
| 型号： | ISL6260CCRZ-T |
| 厂商： | Intersil |
| 文件页数： | 21/28页 |
| 文件大小： | 0K |
| 描述： | IC REG PWM MULTI-PHASE 40-QFN |
| 标准包装： | 4,000 |
| 应用： | 转换器，Intel IMVP-6 |
| 输出数： | 1 |
| 输出电压： | 0.3 V ~ 1.5 V |
| 工作温度： | -10°C ~ 100°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 40-VFQFN 裸露焊盘 |
| 供应商设备封装： | 40-QFN（6x6） |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页当前第21页第22页第23页第24页第25页第26页第27页第28页
ISL6260C
determine the choice of the SOFT capacitor, C SOFT , by
Equation 1:
As mentioned in the “Theory of Operation” on page 17 of this
datasheet, CLK_EN# is logic level high at start-up. When the
I GV
SLEWRATE
C SOFT = ------------------------------------
(EQ. 1)
output voltage reaches 90% of Boot voltage, a counter is
enabled, it counts 13 switching cycles, about 43μs for
C SOFT = ------------------ = 0.0205 μ F
10mV
1 μ s
dV I SS 42 μ A mV (EQ. 3)
0.015 μ F
μ s
C SOFT
------- = ------------------- = ----------------------- = 2.8 ---------
Using a SLEWRATE of 10mV/μs, and the typical I GV value,
given in the Table Electrical Specifications on page 4 of
205μA, C SOFT is:
205 μ A
(EQ. 2)
----------------
A choice of 0.015μF would guarantee a SLEWRATE of
10mV/μs is met for minimum I GV value, given in the
Now this choice of C SOFT will then control the start-up
slewrate as well. One should expect the output voltage to
slew to the Boot value of 1.2V at a rate given by Equation 3:
dt
Generally, when output voltage is approaching its steady
state, its dv/dt will slow down to prevent overshoot. In order
to compensate the slow-down effect, faster initial dv/dt slew
rates can be used with small soft capacitors such as 10nF to
achieve the desired overall dv/dt in the allocated time
interval.
Selecting R BIAS
To properly bias the ISL6260C, a reference current is
established by placing a 147k Ω , 1% tolerance resistor from
the R BIAS pin to ground. This will provide a highly accurate,
10 μ A current source from which OCSET reference current
can be derived.
Care should be taken in layout that the resistor is placed
very close to the R BIAS pin and that a good quality signal
ground is connected to the opposite side of the R BIAS
resistor. Do not connect any other components to this pin.
Capacitance on this pin would create instabilities and should
be avoided.
Start-up Operation - CLK_EN# and PGOOD
The ISL6260C provides a 3.3V logic output pin for
CLK_EN#. The 3V3 pin allows for a system 3.3V source to
be connected to separated circuitry inside the ISL6260C,
solely devoted to the CLK_EN# function. The output is a
3.3V CMOS signal with 4mA of source and sinking
capability. This implementation removes the need for an
external pull-up resistor on this pin, and due to the normal
level of this signal being a low, removes the leakage path
from the 3.3V supply to ground through the pull-up resistor.
This reduces 3.3V supply current, that would occur under
normal operation with a pull-up resistor, and prolongs battery
life. The 3.3V supply should be decoupled to digital ground,
not to analog ground for noise immunity.
21
300kHz operation, then CLK_EN# goes low. This in turn
triggers an internal timer for the IMVP-6+_PWRGD signal.
This timer allows IMVP-6+_PWRGD to go high
approximately 7ms after CLK_EN# goes low.
Static Mode of Operation - Processor Die Sensing
Die sensing allows the Voltage Regulator to compensate for
various resistive drops in the power path and insure that the
voltage seen at the CPU die is the correct level independent
of load current.
The VSEN and RTN pins of the ISL626C are connected to
Kelvin sense leads at the die of the processor through the
processor socket. These signal names are V CC_SENSE and
V CC_SENSE respectively. This allows the Voltage Regulator
to tightly control the processor voltage at the die,
independent of layout inconsistencies and drops. This Kelvin
sense technique provides for extremely tight load line
regulation.
These traces should be laid out as noise sensitive traces.
For optimum load line regulation performance, the traces
connecting these two pins to the Kelvin sense leads of the
processor must be laid out in parallel and away from rapidly
rising voltage nodes (switching nodes) and other noisy
traces. To achieve optimum performance, place common
mode and differential mode RC filters to analog ground on
VSEN and RTN as shown in Figure 46. However, the filter
resistors should be in order of 10 Ω so that they do not
interact with the 50k Ω input resistance of the differential
amplifier.
Due to the fact that the voltage feedback to the switching
regulator is sensed at the processor die, there exists the
potential of an overvoltage due to an open circuit feedback
signal, should the regulator be operated without the
processor installed. Due to this fact, we recommend the use
of the Ropn1 and Ropn2 connected to V OUT and ground as
shown in Figure 46. These resistors will provide voltage
feedback in the event that the system is powered up without
a processor installed. These resistors are typically 100 Ω .
Setting the Switching Frequency - FSET
The R 3 modulator scheme is not a fixed frequency PWM
architecture. The switching frequency can increase during
the application of a load to improve transient performance.
However, it also varies slightly due changes in input and
output voltage and output current, but this variation is
normally less than 10% in continuous conduction mode.
Refer to Figure 39. A resistor connected between the VW
and COMP pins of the ISL6260C adjusts the switching
window, and therefore adjusts the switching frequency. The
Rfset resistor that sets up the switching frequency of the
FN9259.3
June 21, 2010
相关PDF资料 |
PDF描述 |
|---|---|
| ESM22DKKN | CONN EDGECARD 44POS .156 WW |
| UPM1C331MPD | CAP ALUM 330UF 16V 20% RADIAL |
| EL5525IREZ-T7 | IC VREF GEN 18CH TFTLCD 38HTSSOP |
| RCM22DTAN-S189 | CONN EDGECARD 44POS R/A .156 SLD |
| EL5525IREZ-T13 | IC VREF GEN 18CH TFTLCD 38HTSSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL6260CIRZ | 功能描述:电流型 PWM 控制器 MULTI-PHS(3 PHS EXT DC/DC BUCK CONT RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| ISL6260CIRZ-T | 功能描述:电流型 PWM 控制器 MULTI-PHS(3 PHS EXT DC/DC BUCK CONT RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| ISL6260CRZ | 功能描述:直流/直流开关调节器 MULTI-PHS3 PHS EXT DC/DC BUCK CNTRLR RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5 |
| ISL6260CRZR5242 | 制造商:Intersil Corporation 功能描述:53289C01 MASK ONLY WITH DOT ON BRAND - Rail/Tube |
| ISL6260CRZ-T | 功能描述:直流/直流开关调节器 MULTI-PHS3 PHS EXT BUCK CONT IMVP-6 4 RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5 |
发布紧急采购，3分钟左右您将得到回复。