- 您现在的位置：买卖IC网 > PDF目录13126 > ISL6263CHRZ (Intersil)IC VOLT REG 1PH 5BIT VID 32-QFN PDF资料下载
参数资料
| 型号： | ISL6263CHRZ |
| 厂商： | Intersil |
| 文件页数： | 8/18页 |
| 文件大小： | 0K |
| 描述： | IC VOLT REG 1PH 5BIT VID 32-QFN |
| 标准包装： | 60 |
| 应用： | 转换器，GPU 内核电源 |
| 输入电压： | 5 V ~ 25 V |
| 输出数： | 1 |
| 输出电压： | 0.41 V ~ 1.29 V |
| 工作温度： | -10°C ~ 100°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 32-VFQFN 裸露焊盘 |
| 供应商设备封装： | 32-QFN（5x5） |
| 包装： | 管件 |
| 产品目录页面： | 1248 (CN2011-ZH PDF) |
ISL6263C
Functional Pin Descriptions
RBIAS (Pin 1) - Sets the internal 10μ A current reference.
Connect a 150k ? ±1 % resistor from RBIAS to VSS.
SOFT (Pin 2) - Sets the output voltage slew-rate. Connect
an X5R or X7R ceramic capacitor from SOFT to VSS. The
SOFT pin is the non-inverting input of the error amplifier.
OCSET (Pin 3) - Sets the overcurrent threshold. Connect a
resistor from OCSET to VO.
VW (Pin 4) - Sets the static PWM switching frequency in
continuous conduction mode. Connect a resistor from VW to
COMP.
COMP (Pin 5) - Connects to the output of the control loop
error amplifier.
FB (Pin 6) - Connects to the inverting input of the control
loop error amplifier.
VDIFF (Pin 7) - Connects to the output of the VDIFF
differential amplifier. Together with the FB pin, it is used for
the output voltage feedback.
VSEN (Pin 8) - This is the V OUT input of the GPU processor
Kelvin connection. Connects internally to the non-inverting
inputs of the VDIFF differential amplifier.
RTN (Pin 9) - This is the V GND input of the GPU processor
Kelvin connection. Connects internally to the inverting inputs
of the VDIFF differential amplifier.
ICOMP (Pin 10) - Connects to the output of the differential
current sense amplifier and to the non-inverting inputs of the
overcurrent comparator. Used for output current monitor and
overcurrent protection.
ISN (Pin 11) - This is the feedback of the current sense
amplifier. Connects internally to the inverting input of the
current sense amplifier. Used for output current sense.
VO (Pin 12) - Connects to the inverting inputs of the VDIFF
differential amplifier.
ISP (Pin 13) - Connects to the non-inverting input of the
current sense amplifier. Used for output current sense.
VIN (Pin 14) - Connects to the R 3 PWM modulator providing
input voltage feed-forward. For optimum input voltage
transient response, connect near the drain of the high-side
MOSFETs.
VSS (Pin 15) - Analog ground.
VDD (Pin 16) - Input power supply for the IC. Connect to
+5VDC and decouple with at least a 1μF MLCC capacitor
from the VDD pin to the VSS pin.
BOOT (Pin 17) - Input power supply for the high-side
MOSFET gate driver. Connect an MLCC bootstrap capacitor
from the BOOT pin to the PHASE pin.
8
UGATE (Pin 18) - High-side MOSFET gate driver output.
Connect to the gate of the high-side MOSFET.
PHASE (Pin 19) - Current return path for the UGATE
high-side MOSFET gate driver. Detects the polarity of the
PHASE node voltage for diode emulation. Connect the
PHASE pin to the drains of the low-side MOSFETs.
PGND (Pin 20) - Current return path for the LGATE low-side
MOSFET gate driver. The PGND pin only conducts current
when LGATE pulls down. Connect the PGND pin to the
sources of the low-side MOSFETs.
LGATE (Pin 21) - Low-side MOSFET gate driver output.
Connect to the gate of the low-side MOSFET.
PVCC (Pin 22) - Input power supply for the low-side
MOSFET gate driver, and the high-side MOSFET gate
driver, via the internal bootstrap diode connected between
the PVCC and BOOT pins. Connect to +5VDC and decouple
with at least 1μF of an MLCC capacitor from the PVCC pin to
the PGND pin.
VID0:VID4 (Pin 23:Pin 27) - Voltage identification inputs.
VID0 input is the least significant bit (LSB) and VID4 input is
the most significant bit (MSB).
IMON (Pin 28) - A voltage signal proportional to the output
current of the converter.
VR_ON (Pin 29) - A high logic signal on this pin enables the
converter and a low logic signal disables the converter.
AF_EN (Pin 30) - Used in conjunction with VID0:VID4 and
FDE pins to program the diode-emulation and audio filter
behavior. Refer to Table 2.
PGOOD (Pin 31) - The PGOOD pin is an open-drain output
that indicates when the converter is able to supply regulated
voltage. Connect the PGOOD pin to a maximum of 5V
through a pull-up resistor.
FDE (Pin 32) - Used in conjunction with VID0:VID4 and
AF_EN pins to program the diode-emulation and audio filter
behavior. Refer to Table 2.
BOTTOM - Connects to substrate. Electrically isolated but
should be connected to VSS. Requires best practical
thermal coupling to PCB.
FN6745.1
July 8, 2010
相关PDF资料 |
PDF描述 |
|---|---|
| 1945-38J | COIL RF 910UH MOLDED UNSHIELDED |
| EBA49DTAT | CONN EDGECARD 98POS R/A .125 SLD |
| VI-B21-EW-S | CONVERTER MOD DC/DC 12V 100W |
| 1945-37J | COIL RF 820UH MOLDED UNSHIELDED |
| 1945-36J | COIL RF 750UH MOLDED UNSHIELDED |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL6263CHRZ-T | 功能描述:直流/直流开关调节器 1-PHS INT DC/DC BUCK CNTRLR IMVP-6 W/IMON RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5 |
| ISL6263CRZ | 功能描述:直流/直流开关调节器 1 PHS INT DC/DC BUCK CNTRLR FOR INTEL RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5 |
| ISL6263CRZ-T | 功能描述:直流/直流开关调节器 1 PHS INT DC/DC BUCK CNTRLR FOR INTEL RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5 |
| ISL6263DEVAL1Z | 功能描述:EVAL BAORD 1 FOR ISL6263D RoHS:是 类别:编程器，开发系统 >> 评估板 - DC/DC 与 AC/DC（离线）SMPS 系列:* 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:True Shutdown™ 主要目的:DC/DC，步升 输出及类型:1，非隔离 功率 - 输出:- 输出电压:- 电流 - 输出:1A 输入电压:2.5 V ~ 5.5 V 稳压器拓扑结构:升压 频率 - 开关:3MHz 板类型:完全填充 已供物品:板 已用 IC / 零件:MAX8969 |
| ISL6263DHRZ | 功能描述:IC VREG 3BIT 1PHASE 32-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,000 系列:- 应用:电源，ICERA E400，E450 输入电压:4.1 V ~ 5.5 V 输出数:10 输出电压:可编程 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:42-WFBGA，WLCSP 供应商设备封装:42-WLP 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。