- 您现在的位置：买卖IC网 > PDF目录15190 > ISL6269BIRZ-T (Intersil)IC REG CTRLR BUCK PWM 16-QFN PDF资料下载
参数资料
| 型号： | ISL6269BIRZ-T |
| 厂商： | Intersil |
| 文件页数： | 11/14页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR BUCK PWM 16-QFN |
| 标准包装： | 6,000 |
| 系列： | Robust Ripple Regulator™ (R³) |
| PWM 型： | 控制器 |
| 输出数： | 1 |
| 频率 - 最大： | 600kHz |
| 电源电压： | 5 V ~ 25 V |
| 降压： | 是 |
| 升压： | 无 |
| 回扫： | 无 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | -40°C ~ 100°C |
| 封装/外壳： | 16-VQFN 裸露焊盘 |
| 包装： | 带卷 (TR) |
ISL6269B
V OUT
General Application Design Guide
This design guide is intended to provide a high-level
explanation of the steps necessary to create a single-phase
power converter. It is assumed that the reader is familiar with
many of the basic skills and techniques referenced below. In
addition to this guide, Intersil provides complete reference
designs that include schematics, bills of materials, and
example board layouts.
Selecting the LC Output Filter
The duty cycle of an ideal buck converter is a function of the
input and the output voltage. This relationship is written as:
D = ---------------- (EQ. 9)
V IN
The output inductor peak-to-peak ripple current is written as:
shared by a sufficient quantity of paralleled capacitors so that
they operate below the maximum rated RMS current at f SW .
Take into account that the rated value of a capacitor can fade
as much as 50% as the DC voltage across it increases.
Selection of the Input Capacitor
The important parameters for the bulk input capacitance are
the voltage rating and the RMS current rating. For reliable
operation, select bulk capacitors with voltage and current
ratings above the maximum input voltage and capable of
supplying the RMS current required by the switching circuit.
Their voltage rating should be at least 1.25 times greater
than the maximum input voltage, while a voltage rating of 1.5
times is a preferred rating. Figure 7 is a graph of the input
RMS ripple current, normalized relative to output load current,
as a function of duty cycle that is adjusted for converter
V OUT ? ( 1 – D )
I PP = --------------------------------------
( I MAX ? ( D – D ) ) + ? x ? I MAX ? ------ ?
(EQ. 10)
f SW ? L OUT
A typical step-down DC/DC converter will have an I PP of
20% to 40% of the maximum DC output load current. The
efficiency. The ripple current calculation is written as:
2 2 2 D
? 12 ?
I IN_RMS = -----------------------------------------------------------------------------------------------------
I MAX
(EQ. 14)
value of I PP is selected based upon several criteria such as
MOSFET switching loss, inductor core loss, and the resistive
loss of the inductor winding. The DC copper loss of the
inductor can be estimated by:
Where:
- I MAX is the maximum continuous I LOAD of the converter
- x is a multiplier (0 to 1) corresponding to the inductor
peak-to-peak ripple amplitude expressed as a
P COPPER = I LOAD
2
?
DCR
(EQ. 11)
percentage of I MAX (0% to 100%)
- D is the duty cycle that is adjusted to take into account
V OUT
V IN ? EFF
Where I LOAD is the converter output DC current.
The copper loss can be significant so attention has to be
given to the DCR selection. Another factor to consider when
choosing the inductor is its saturation characteristics at
elevated temperature. A saturated inductor could cause
destruction of circuit components, as well as nuisance OCP
faults.
A DC/DC buck regulator must have output capacitance
C OUT into which ripple current I PP can flow. Current I PP
develops a corresponding ripple voltage V PP across C OUT,
which is the sum of the voltage drop across the capacitor
ESR and of the voltage change stemming from charge
moved in and out of the capacitor. These two voltages are
written as:
the efficiency of the converter which is written as:
D = --------------------------
(EQ. 15)
In addition to the bulk capacitance, some low ESL ceramic
capacitance is recommended to decouple between the drain
of the high-side MOSFET and the source of the low-side
MOSFET.
0.60
0.55
0.50
0.45
0.40
0.35
0.30
Δ V C = -------------------------------------
Δ V ESR = I PP ? E SR
and
I PP
8 ? C OUT ? f SW
(EQ. 12)
(EQ. 13)
0.25
0.20
0.15
0.10
0.05
x=1
x = 0.75
x = 0.50
x = 0.25
x=0
0
If the output of the converter has to support a load with high
0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
1
pulsating current, several capacitors will need to be paralleled
to reduce the total ESR until the required V PP is achieved.
The inductance of the capacitor can cause a brief voltage dip
if the load transient has an extremely high slew rate. Low
inductance capacitors constructed with reverse package
geometry are available. A capacitor dissipates heat as a
function of RMS current and frequency. Be sure that I PP is
11
DUTY CYCLE
FIGURE 7. NORMALIZED RMS INPUT CURRENT FOR x = 0.8
FN6280.2
May 30, 2007
相关PDF资料 |
PDF描述 |
|---|---|
| RCM22DRSN | CONN EDGECARD 44POS DIP .156 SLD |
| HCC15DRYN-S93 | CONN EDGECARD 30POS DIP .100 SLD |
| SLP103M025C5P3 | CAP ALUM 10000UF 25V 20% SNAP |
| HCC15DRYH-S93 | CONN EDGECARD 30POS DIP .100 SLD |
| SLP331M200C3P3 | CAP ALUM 330UF 200V 20% SNAP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL6269CRZ | 功能描述:IC REG CTRLR BUCK PWM 16-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:Robust Ripple Regulator™ (R³) 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:275kHz 占空比:50% 电源电压:18 V ~ 110 V 降压:无 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:是 工作温度:-40°C ~ 85°C 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:带卷 (TR) |
| ISL6269CRZ-T | 功能描述:IC REG CTRLR BUCK PWM 16-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:Robust Ripple Regulator™ (R³) 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:275kHz 占空比:50% 电源电压:18 V ~ 110 V 降压:无 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:是 工作温度:-40°C ~ 85°C 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:带卷 (TR) |
| ISL6269EVAL2Z | 功能描述:EVALUATION BOARD FOR ISL6269 RoHS:是 类别:编程器，开发系统 >> 评估板 - DC/DC 与 AC/DC（离线）SMPS 系列:Robust Ripple Regulator™ (R³) 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:True Shutdown™ 主要目的:DC/DC，步升 输出及类型:1，非隔离 功率 - 输出:- 输出电压:- 电流 - 输出:1A 输入电压:2.5 V ~ 5.5 V 稳压器拓扑结构:升压 频率 - 开关:3MHz 板类型:完全填充 已供物品:板 已用 IC / 零件:MAX8969 |
| ISL6269IRZ | 功能描述:IC REG CTRLR BUCK PWM 16-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:Robust Ripple Regulator™ (R³) 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:275kHz 占空比:50% 电源电压:18 V ~ 110 V 降压:无 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:是 工作温度:-40°C ~ 85°C 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:带卷 (TR) |
| ISL6269IRZ-T | 功能描述:IC REG CTRLR BUCK PWM 16-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:Robust Ripple Regulator™ (R³) 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:275kHz 占空比:50% 电源电压:18 V ~ 110 V 降压:无 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:是 工作温度:-40°C ~ 85°C 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。