参数资料
| 型号： | ISL62881CIRTZ |
| 厂商： | Intersil |
| 文件页数： | 18/37页 |
| 文件大小： | 0K |
| 描述： | IC REG PWM SGL PHASE 28TQFN |
| 标准包装： | 75 |
| 应用： | 控制器，Intel IMVP-6.5? |
| 输入电压： | 4.5 V ~ 25 V |
| 输出数： | 1 |
| 输出电压： | 0.013 V ~ 1.5 V |
| 工作温度： | -40°C ~ 100°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-WFQFN 裸露焊盘 |
| 供应商设备封装： | 28-TQFN-EP（4x4） |
| 包装： | 管件 |
| 配用： | ISL62881CCPUEVAL2Z-ND - EVAL BOARD ISL62881CCPU 28QFN |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页当前第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页
ISL62881C, ISL62881D
As Figures 1 and 2 show, a resistor R imon is connected to
the IMON pin to convert the IMON pin current to voltage.
A capacitor can be paralleled with R imon to filter the
voltage information. The IMVP-6.5? specification
requires that the IMON voltage information be referenced
to VSS SENSE .
The IMON pin voltage range is 0V to 1.1V. A clamp circuit
prevents the IMON pin voltage from going above 1.1V.
Adaptive Body Diode Conduction Time
Reduction
In DCM, the controller turns off the low-side MOSFET
when the inductor current approaches zero. During
on-time of the low-side MOSFET, phase voltage is
negative and the amount is the MOSFET r DS(ON) voltage
drop, which is proportional to the inductor current. A
phase comparator inside the controller monitors the
phase voltage during on-time of the low-side MOSFET
and compares it with a threshold to determine the
zero-crossing point of the inductor current. If the
inductor current has not reached zero when the low-side
MOSFET turns off, it’ll flow through the low-side MOSFET
body diode, causing the phase node to have a larger
voltage drop until it decays to zero. If the inductor
current has crossed zero and reversed the direction when
the low-side MOSFET turns off, it’ll flow through the
high-side MOSFET body diode, causing the phase node to
have a spike until it decays to zero. The controller
continues monitoring the phase voltage after turning off
the low-side MOSFET and adjusts the phase comparator
threshold voltage accordingly in iterative steps such that
clamped. The ISL62881C will resume normal PWM
operation.
While the overshoot reduction function reduces the
output voltage overshoot, energy is dissipated on the
low-side MOSFET, causing additional power loss. The
more frequent the transient event, the more power loss
is dissipated on the low-side MOSFET. The MOSFET may
face severe thermal stress when transient events happen
at a high repetitive rate. User discretion is advised when
this function is enabled.
Key Component Selection
R BIAS
The ISL62881C uses a resistor (1% or better tolerance is
recommended) from the RBIAS pin to GND to establish
highly accurate reference current sources inside the IC.
Using R BIAS = 147k Ω sets the controller for CPU core
application and using R bias = 47k Ω sets the controller for
GPU core application. Do not connect any other
components to this pin. Do not connect any capacitor to
the RBIAS pin as it will create instability.
Care should be taken in layout that the resistor is placed
very close to the RBIAS pin and that a good quality
signal ground is connected to the opposite side of the
R BIAS resistor.
Inductor DCR Current-Sensing Network
PHASE
the low-side MOSFET body diode conducts for
approximately 40ns to minimize the body diode-related
loss.
RSUM
ISUM+
Overshoot Reduction Function
The ISL62881C has an optional overshoot reduction
function, enabled or disabled by the resistor from the
COMP pin to GND, as shown in Table 3.
When a load release occurs, the energy stored in the
inductors will dump to the output capacitor, causing
L
DCR
RNTCS
RNTC
RP
+
CN VCN
-
RI
ISUM-
output voltage overshoot. The inductor current
freewheels through the low-side MOSFET during this
period of time. The overshoot reduction function turns off
the low-side MOSFET during the output voltage
overshoot, forcing the inductor current to freewheel
through the low-side MOSFET body diode. Since the body
diode voltage drop is much higher than MOSFET R DS(ON)
voltage drop, more energy is dissipated on the low-side
MOSFET therefore the output voltage overshoot is lower.
If the overshoot reduction function is enabled, the
ISL62881C monitors the COMP pin voltage to determine
the output voltage overshoot condition. The COMP
voltage will fall and hit the clamp voltage when the
output voltage overshoots. The ISL62881C will turn off
LGATE when COMP is being clamped. The low-side
MOSFET in the power stage will be turned off. When the
output voltage has reached its peak and starts to come
down, the COMP voltage starts to rise and is no longer
18
IO
FIGURE 13. DCR CURRENT-SENSING NETWORK
Figure 13 shows the inductor DCR current-sensing
network. An inductor current flows through the DCR and
creates a voltage drop. The inductor has a resistors in
R sum connected to the phase-node-side pad and a PCB
trace connected to the output-side pad to accurately
sense the inductor current by sensing the DCR voltage
drop. The sensed current information is fed to the NTC
network (consisting of R ntcs , R ntc and R p ) and capacitor
C n . R ntc is a negative temperature coefficient (NTC)
thermistor, used to temperature-compensate the
inductor DCR change. The inductor current information is
presented to the capacitor C n . Equations 7 through 11
FN7596.0
March 8, 2010
相关PDF资料 |
PDF描述 |
|---|---|
| ISL62881HRTZ | IC REG PWM SGL PHASE 28TQFN |
| ISL62882IRTZ | IC REG PWM 2PHASE BUCK 40TQFN |
| ISL62883IRTZ | IC REG PWM 3PHASE BUCK 40TQFN |
| ISL6292BCRZ | IC CHARGER LI-ION 4.2V 4X4 16QFN |
| ISL6294IBZ | IC CHRGR LI-ION SGL 8-SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL62881CIRTZ-T | 功能描述:直流/直流开关调节器 1-PHS PWM BUCKG FOR MICROPROC PWR SUPPLY RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5 |
| ISL62881D | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Single-Phase PWM Regulator for IMVP-6.5a?￠ Mobile CPUs and GPUs |
| ISL62881DHRTZ | 功能描述:直流/直流开关调节器 1 PHS CNTRLR W/INTEG DRVR 32LD 5X5 RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5 |
| ISL62881DHRTZ-T | 功能描述:直流/直流开关调节器 1 PHS CNTRLR W/INTEG DRVR 32LD 5X5 RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5 |
| ISL62881HRTZ | 功能描述:直流/直流开关调节器 1 PHS PWM BUCKG FOR MICROPROCESR PWR SUP RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5 |
发布紧急采购，3分钟左右您将得到回复。