- 您现在的位置：买卖IC网 > PDF目录383144 > ISL6292B (Intersil Corporation) Dual Positive-Edge-Triggered D-Type Flip-Flops With Clear and Preset 14-SSOP -40 to 85 PDF资料下载
参数资料
| 型号： | ISL6292B |
| 厂商： | Intersil Corporation |
| 英文描述： | Dual Positive-Edge-Triggered D-Type Flip-Flops With Clear and Preset 14-SSOP -40 to 85 |
| 中文描述： | Li-ion/Li聚合物电池充电器 |
| 文件页数： | 9/12页 |
| 文件大小： | 287K |
| 代理商： | ISL6292B |
9
FN9139 .1
April 19, 2005
C
TIME
is the timing capacitor shown in the Typical
Application circuit. A 1nF capacitor leads to 14 minutes of
TIMEOUT. For example, a 15nF capacitor sets the
TIMEOUT to be 3.5 hours. The charger is terminated when
the TIMEOUT is reached.
The trickle mode charge has a time limit of 1/8 TIMEOUT. If
the battery voltage does not reach V
MIN
within that limit, a
TIMEOUT fault is issued and the charger latches up. The
charger stays in trickle mode for at least 15 cycles of the
internal oscillator and, at most, 1/8 of TIMEOUT.
Recharge Threshold
The charger terminates when the TIMEOUT limit expires.
After the termination, if the battery is below the recharge
threshold given in the Electrical Specification table, the
charger starts a re-charge cycle.
LED Indications
RED and GRN are two open-drain outputs that directly drive
a tri-color LED. At the moment when the power is applied or
when the charger is enabled through the EN pin, the charger
starts to charge and the RED indication pin outputs a low
impedance to drive a red LED. Once the charge finishes
(either when the EOC condition is qualified or when the
TIMEOUT completes), the GRN pin turns on to drive a green
LED and the red LED is off. The green LED remains on
unless the input power is recycled, or when the EN pin is
toggled, or a fault case happens. When a recharge occurs,
the indication remains in green.
When a fault case happens, both the RED and the GRN pins
are on to indicate a yellow color.
If the FAULT is a TIMEOUT
fault, the yellow indication is latched and can only be reset
through the EN pin or the input power. If the FAULT is an
ambient temperature FAULT, the charger restarts after the
fault condition is removed. When not powered or when not
enabled, both LEDs are off. Table 1 summarizes the LED
indications.
VSEN Pin
The VSEN pin allows remote sensing of the battery voltage
to minimize the resistive voltage drop between the charger
output and the battery positive terminal. Figure 5 shows the
internal voltage feedback circuit. In applications that the
remote sense pin goes through a connector, a local low-
value resistor is recommended, as the R
1
shown in Figure 5,
in case the connector has bad contact. The sum of R
2
and
R
3
is 75k
, therefore, a 10
R
1
is negligible in output
voltage accuracy.
Ambient Temperature Sensing
The TEMP pin is used to set the ambient temperature range
that allows charging the battery. Typically, an NTC (negative
temperature coefficient) resistor is mounted on the printed
circuit board (PCB) to monitor the ambient temperature. Due
to the self-heating of the PCB during charging, the ISL6292B
provides the DT pin to set a higher temperature threshold
after the charger starts.
Figure 6 shows the internal circuit for the ambient
temperature sensing function. The two comparators form a
window comparator whose high-threshold is V
TMIN
and low-
threshold is V
TMAX
. These two thresholds are given in the
Electrical Specifications. The two MOSFETs (Q1 and Q2)
FIGURE 5. THE INTERNAL VOLTAGE FEEDBACK CIRCUIT
+
-
BAT
VSEN
R2
Q1
R3
VA
Enable
V
REF
R1
10
TABLE 1. LED INDICATION SUMMARY
STATUS
RED GRN
INDICATION
Charging
L
H
Red
Full Charge (EOC), or recharging
H
L
Green
Trickle TIMEOUT Error
L
L
Yellow (Latched)
Over/Under Ambient Temperature
L
L
Yellow
No Battery
H
H
Off
FIGURE 6. THE INTERNAL AND EXTERNAL CIRCUIT FOR
THE NTC INTERFACE
+
-
+
-
V2P9
TEMP
DT
2.9V
R1
100K
R2
75K
R3
25K
R4
4K
Q1
Q2
CP1
CP2
Under
Temp
Over
Temp
R
U
To TEMP Pin
V
TMIN
V
TMAX
R
T
Q3
R
D
GND
CHG
ISL6292B
相关PDF资料 |
PDF描述 |
|---|---|
| ISL6292CCR3Z-T | Li-ion/Li Polymer Battery Charger |
| ISL6292CCR3Z | Dual Positive-Edge-Triggered D-Type Flip-Flops With Clear and Preset 14-SOIC -40 to 85 |
| ISL6292DCR4 | Li-ion/Li Polymer Battery Charger |
| ISL6292D | Dual Positive-Edge-Triggered D-Type Flip-Flops With Clear and Preset 14-SOIC -40 to 85 |
| ISL6292DCR4-T | Li-ion/Li Polymer Battery Charger |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL6292BCR | 功能描述:IC BATT CHRGR LI-ION 4.2V 16-QFN RoHS:否 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 标准包装:1 系列:- 功能:充电管理 电池化学:锂离子（Li-Ion）、锂聚合物（Li-Pol） 电源电压:3.75 V ~ 6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SC-74A，SOT-753 供应商设备封装:SOT-23-5 包装:剪切带 (CT) 产品目录页面:669 (CN2011-ZH PDF) 其它名称:MCP73831T-2ACI/OTCT |
| ISL6292BCR-T | 功能描述:IC BATT CHRGR LI-ION 4.2V 16-QFN RoHS:否 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 标准包装:1 系列:- 功能:充电管理 电池化学:锂离子（Li-Ion）、锂聚合物（Li-Pol） 电源电压:3.75 V ~ 6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SC-74A，SOT-753 供应商设备封装:SOT-23-5 包装:剪切带 (CT) 产品目录页面:669 (CN2011-ZH PDF) 其它名称:MCP73831T-2ACI/OTCT |
| ISL6292BCRZ | 功能描述:IC CHARGER LI-ION 4.2V 4X4 16QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 功能:电池监控器 电池化学:碱性，锂离子，镍镉，镍金属氢化物 电源电压:1 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-6 供应商设备封装:SOT-6 包装:带卷 (TR) |
| ISL6292BCRZ-T | 功能描述:IC CHARGER LI-ION POLYMER 16-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 功能:电池监控器 电池化学:碱性，锂离子，镍镉，镍金属氢化物 电源电压:1 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-6 供应商设备封装:SOT-6 包装:带卷 (TR) |
| ISL6292C | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Li-ion/Li Polymer Battery Charger |
发布紧急采购，3分钟左右您将得到回复。