参数资料
| 型号： | ISL6336CRZ |
| 厂商： | Intersil |
| 文件页数： | 11/31页 |
| 文件大小： | 0K |
| 描述： | IC CTRLR PWM 6PHASE BUCK 48-QFN |
| 标准包装： | 43 |
| 应用： | 控制器，Intel VR11.1 |
| 输入电压： | 3 V ~ 12 V |
| 输出数： | 1 |
| 输出电压： | 0.5 V ~ 1.6 V |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 48-VFQFN 裸露焊盘 |
| 供应商设备封装： | 48-QFN（7x7） |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页当前第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页
ISL6336, ISL6336A
OFS - The OFS pin provides a means to program a DC
offset current for generating a DC offset voltage at the REF
input. The offset current is generated via an external resistor
and precision internal voltage references. The polarity of the
offset is selected by connecting the resistor to GND or VCC.
For no offset, the OFS pin should be left unterminated.
TCOMP - Temperature compensation scaling input. The
voltage sensed on the TM pin is utilized as the temperature
input to adjust I DROOP and the overcurrent protection limit to
effectively compensate for the temperature coefficient of the
current sense element. To implement the integrated
temperature compensation, a resistor divider circuit is needed
with one resistor being connected from TCOMP to VCC of the
controller and another resistor being connected from TCOMP
to GND. Changing the ratio of the resistor values will set the
gain of the integrated thermal compensation. When integrated
temperature compensation function is not used, connect
TCOMP to GND.
OVP - The overvoltage protection output indication pin. This
pin can be pulled to VCC and is latched when an overvoltage
condition is detected. When the OVP indication is not used,
keep this pin open.
IMON - IMON is a current output of the average of the sum
of each phase’s sensed current. A resistor connected from
IMON to GND will produce a voltage that is proportional to
the regulator current. The voltage at this pin is internally
clamped to 1.12V. If the voltage reaches 1.12V the clamp is
activated an overcurrent shutdown will be initiated.
Place a resistor from this pin to GND. A capacitor in parallel
with this resistor is required. The capacitor should be sized
for a minimum time constant of 300μs.
TM - TM is an input pin for VR temperature measurement.
Connect this pin through NTC thermistor to GND and a resistor
to VCC of the controller. The voltage at this pin is reverse
proportional to the VR temperature. ISL6336, ISL6336A
monitors the VR temperature based on the voltage at the TM
pin and the output signals at VR_HOT and VR_FAN.
VR_HOT - VR_HOT is used as an indication of high VR
temperature. It is an open-drain logic output. It will be open
when the measured VR temperature reaches a certain level.
VR_FAN - VR_FAN is an output pin with open-drain logic
output. It will be open when the measured VR temperature
reaches a certain level.
PSI# - The PSI# pin is used to change the state of the
controller. When PSI# is asserted the controller will change
controller resumes normal operation when this pin is pulled
HIGH. This pin has a 40μA internal pull-up to about 1V.
APA - The APA pin is used to adjust the Adaptive Phase
Alignment trip level. A 50μA current source flows into this pin.
A resistor connected from this pin to COMP sets the voltage
trip level. A small decoupling capacitor should be placed in
parallel with the resistor for high frequency decoupling.
Operation
Multiphase Power Conversion
Microprocessor load current profiles have changed to the
point that the advantages of multiphase power conversion
are impossible to ignore. The technical challenges
associated with producing a single-phase converter which is
both cost-effective and thermally viable, have forced a
change to the cost-saving approach of multiphase. The
ISL6336, ISL6336A controller helps reduce the complexity of
implementation by integrating vital functions and requiring
and 6 provide top level views of multiphase power
conversion using the ISL6336, ISL6336A controller.
Interleaving
The switching of each channel in a multiphase converter is
timed to be symmetrically out of phase with each of the other
channels. In a 3-phase converter for example, each channel
switches 1/3 cycle after the previous channel and 1/3 cycle
before the following channel. As a result, the three-phase
converter has a combined ripple frequency 3x greater than
the ripple frequency of any one phase. In addition, the
peak-to-peak amplitude of the combined inductor current is
reduced in proportion to the number of phases (see
Equations 1 and 2). The increased ripple frequency and the
lower ripple amplitude mean that the designer can use less
per-channel inductance and lower total output capacitance
for any performance specification.
Figure 1 illustrates the multiplicative effect on output ripple
frequency. The three channel currents (IL1, IL2, and IL3)
combine to form the AC ripple current and the DC load
current. The ripple component has 3x the ripple frequency of
each individual channel current. Each PWM pulse is
triggered 1/3 of a cycle after the start of the PWM pulse of the
previous phase. The DC components of the inductor currents
combine to feed the load.
To understand the reduction of the ripple current amplitude in
the multiphase circuit, examine Equation 1, which represents
an individual channel’s peak-to-peak inductor current.
( V IN – V OUT ) ? V OUT
L ? f S ? V
the operating state to improve light load efficiency. The
controller drops the number of active phases to 1-phase or
2-phase operation with diode emulation according to the logic
I PP = ----------------------------------------------------------
IN
(EQ. 1)
shown in Table 1. The FS and SS pins are used to optimize
light load efficiency for non-coupled inductor, 2-phase coupled
inductor, and (n-x)-phase coupled inductor applications. The
11
In Equation 1, V IN and V OUT are the input and the output
voltages respectively, L is the single-channel inductor value,
and f S is the switching frequency.
FN6504.1
May 28, 2009
相关PDF资料 |
PDF描述 |
|---|---|
| X40030S14I-AT1 | IC VOLTAGE MONITOR TRPL 14-SOIC |
| ASC25DREH-S13 | CONN EDGECARD 50POS .100 EXTEND |
| ASM11DSAN | CONN EDGECARD 22POS R/A .156 SLD |
| UVY2E100MPD | CAP ALUM 10UF 250V 20% RADIAL |
| ASM11DSAH | CONN EDGECARD 22POS R/A .156 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL6336CRZ-T | 功能描述:IC CTRLR PWM 6PHASE BUCK 48-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 标准包装:43 系列:- 应用:控制器，Intel VR11 输入电压:5 V ~ 12 V 输出数:1 输出电压:0.5 V ~ 1.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-VFQFN 裸露焊盘 供应商设备封装:48-QFN（7x7） 包装:管件 |
| ISL6336IRZ | 功能描述:IC CTRLR PWM 6PHASE BUCK 48-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 标准包装:43 系列:- 应用:控制器，Intel VR11 输入电压:5 V ~ 12 V 输出数:1 输出电压:0.5 V ~ 1.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-VFQFN 裸露焊盘 供应商设备封装:48-QFN（7x7） 包装:管件 |
| ISL6336IRZ-T | 功能描述:IC CTRLR PWM 6PHASE BUCK 48-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 标准包装:43 系列:- 应用:控制器，Intel VR11 输入电压:5 V ~ 12 V 输出数:1 输出电压:0.5 V ~ 1.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-VFQFN 裸露焊盘 供应商设备封装:48-QFN（7x7） 包装:管件 |
| ISL6341ACRZ | 功能描述:电流型 PWM 控制器 10LD 3X3 SYNC PWM BUCK CNTRLR 5V OR RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| ISL6341ACRZ-T | 功能描述:IC REG CTRLR BUCK PWM VM 10-TDFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:275kHz 占空比:50% 电源电压:18 V ~ 110 V 降压:无 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:是 工作温度:-40°C ~ 85°C 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。