参数资料
| 型号： | ISL6405ERZ |
| 厂商： | Intersil |
| 文件页数： | 11/13页 |
| 文件大小： | 0K |
| 描述： | IC VOLT REG DUAL LNB 32-QFN |
| 标准包装： | 60 |
| 应用： | 转换器，卫星信号接收机顶盒设计 |
| 输入电压： | 8 V ~ 14 V |
| 输出数： | 2 |
| 输出电压： | 13 V ~ 18 V |
| 工作温度： | -20°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 32-VFQFN 裸露焊盘 |
| 供应商设备封装： | 32-QFN（5x5） |
| 包装： | 管件 |
ISL6405
Received Data ( I 2 C bus READ MODE)
The ISL6405 can provide to the master a copy of the system
register information via the I 2 C bus in read mode. The read
mode is Master activated by sending the chip address with
R/W bit set to 1. At the following Master generated clock bits,
the ISL6405 issues a byte on the SDA data bus line (MSB
transmitted first).
At the ninth clock bit the MCU master can:
? Acknowledge the reception, starting in this way the
transmission of another byte from the ISL6405.
? Not acknowledge, stopping the read mode
communication.
While the whole register is read back by the microprocessor,
only the two read-only bits, OLF and OTF, convey diagnostic
information about the ISL6405.
After selection of SR1/SR2 ?
Power–On I 2 C Interface Reset
The I 2 C interface built into the ISL6405 is automatically reset
at power-on. The I 2 C interface block will receive a Power OK
logic signal from the UVLO circuit. This signal will go HIGH
when chip power is OK. As long as this signal is LOW, the
interface will not respond to any I 2 C commands and the
system register SR1 and SR2 are initialized to all zeros, thus
keeping the power blocks disabled. Once the Vcc rises
above UVLO, the POWER OK signal given to the I 2 C
interface block will be HIGH, the I 2 C interface becomes
operative and the SRs can be configured by the main
microprocessor. About 400mV of hysteresis is provided in
the UVLO threshold to avoid false triggering of the Power-
On reset circuit. (I 2 C comes up with EN = 0; EN goes HIGH
at the same time as (or later than) all other I 2 C data for that
PWM becomes valid).
ADDRESS Pin
Connecting this pin to GND the chip I 2 C interface address is
0001000, but, it is possible to choose between two different
addresses simply by setting this pin at one of the two fixed
voltage levels as shown in Table 8.
TABLE 6. ADDRESS PIN CHARACTERISTICS
V ADDR MINIMUM TYPICAL MAXIMUM
V ADDR -1 0V - 2V
“0001000”
V ADDR -2 2.7V - 5V
“0001001”
TABLE 7. READING SYSTEM REGISTERS
DCL
ISEL1/2
ENT1/2
LLC1/2
VSEL1/1
EN1/2
OTF2
OLF1/2
FUNCTION
These bits are read as they were after the last write operation.
0
1
0
1
T J ≤ 130°C, normal operation
T J > 150°C, power blocks disabled
I OUT < I MAX , normal operation
I OUT > I MAX , overload protection triggered
I 2 C Electrical Characteristics
TABLE 8. I 2 C SPECIFICATIONS
PARAMETER
TEST CONDITION
MINIMUM
TYPICAL
MAXIMUM
Input Logic High, VIH
Input Logic Low, VIL
Input Logic Current, IIL
SDA, SCL
SDA, SCL
SDA, SCL;
0.4V < V IN < 4.5V
0.7 x V DD
0.3 x V DD
10 μ A
SCL Clock Frequency
0
100kHz
400kHz
11
相关PDF资料 |
PDF描述 |
|---|---|
| MIC5320-SMYMT TR | IC REG LDO 3.3V/2.8V .15A 6-TMLF |
| LT3022EMSE#PBF | IC REG LDO ADJ 1A 16MSOP |
| ISL8101CRZ | IC PWM CTRLR BUCK 2PHASE 24-QFN |
| 2510-50K | INDUCTOR 12UH SMT 10% TOL |
| LT3029EMSE#PBF | IC REG LDO ADJ .5A 16MSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL6405ERZ-T | 功能描述:线性稳压器 - 标准 VER OF ISL6405ER-T RoHS:否 制造商:STMicroelectronics 输出类型: 极性: 输出电压:1.8 V 输出电流:150 mA 负载调节: 最大输入电压:5.5 V 线路调整率: 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:SOT-323-5L |
| ISL6405EVAL1 | 功能描述:EVALUATION BOARD 1 ISL6405 RoHS:否 类别:编程器，开发系统 >> 评估板 - DC/DC 与 AC/DC（离线）SMPS 系列:- 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:True Shutdown™ 主要目的:DC/DC，步升 输出及类型:1，非隔离 功率 - 输出:- 输出电压:- 电流 - 输出:1A 输入电压:2.5 V ~ 5.5 V 稳压器拓扑结构:升压 频率 - 开关:3MHz 板类型:完全填充 已供物品:板 已用 IC / 零件:MAX8969 |
| ISL6405EVAL2 | 功能描述:EVALUATION BOARD 2 ISL6405 RoHS:否 类别:编程器，开发系统 >> 过时/停产零件编号 系列:- 标准包装:1 系列:- 传感器类型:CMOS 成像，彩色（RGB） 传感范围:WVGA 接口:I²C 灵敏度:60 fps 电源电压:5.7 V ~ 6.3 V 嵌入式:否 已供物品:成像器板 已用 IC / 零件:KAC-00401 相关产品:4H2099-ND - SENSOR IMAGE WVGA COLOR 48-PQFP4H2094-ND - SENSOR IMAGE WVGA MONO 48-PQFP |
| ISL6405EVAL2Z | 功能描述:EVAL BOARD 2 FOR ISL6405 RoHS:是 类别:编程器，开发系统 >> 评估板 - DC/DC 与 AC/DC（离线）SMPS 系列:* 标准包装:1 系列:- 主要目的:DC/DC，步降 输出及类型:1，非隔离 功率 - 输出:- 输出电压:3.3V 电流 - 输出:3A 输入电压:4.5 V ~ 28 V 稳压器拓扑结构:降压 频率 - 开关:250kHz 板类型:完全填充 已供物品:板 已用 IC / 零件:L7981 其它名称:497-12113STEVAL-ISA094V1-ND |
| ISL6405I2C-KIT-EVAL | 功能描述:EVALUATION BOARD I2C ISL6405 RoHS:否 类别:编程器，开发系统 >> 过时/停产零件编号 系列:- 标准包装:1 系列:- 传感器类型:CMOS 成像，彩色（RGB） 传感范围:WVGA 接口:I²C 灵敏度:60 fps 电源电压:5.7 V ~ 6.3 V 嵌入式:否 已供物品:成像器板 已用 IC / 零件:KAC-00401 相关产品:4H2099-ND - SENSOR IMAGE WVGA COLOR 48-PQFP4H2094-ND - SENSOR IMAGE WVGA MONO 48-PQFP |
发布紧急采购，3分钟左右您将得到回复。