参数资料
型号: ISL6410IUZ-TK
厂商: Intersil
文件页数: 8/13页
文件大小: 0K
描述: IC REG BUCK SYNC 0.6A 10MSOP
标准包装: 1,000
类型: 降压(降压)
输出类型: 固定
输出数: 1
输出电压: 1.2V,1.5V,1.8V
输入电压: 3 V ~ 3.6 V
PWM 型: 电流模式
频率 - 开关: 750kHz
电流 - 输出: 600mA
同步整流器:
工作温度: -40°C ~ 85°C
安装类型: 表面贴装
封装/外壳: 10-TFSOP,10-MSOP(0.118",3.00mm 宽)
包装: 带卷 (TR)
供应商设备封装: 10-MSOP
ISL6410, ISL6410A
I RMS = Io ( max ) × --------- × ? 1 – --------- ?
1 – ---------
dIL = Vo × -------------------
1 – ---------
I RMS ( Co ) = Vo ×
------------------- × -----------------
2 × 3
Power Good
This output is asserted high when the PWM is enabled, and
Vout is within 8.0% typical of its final value, and is active low
outside this range. When disabled, the output turns active
low. It is recommended to leave the PG pin unconnected
when not used.
PWM Overvoltage and Overcurrent Protection
The PWM output current is sampled at the end of each PWM
cycle, exceeding the overcurrent limit, causes a 4 bit
up/down counter to increment by one LSB. A normal current
state causes the counter to decrement by one LSB (the
counter will not however “rollover” or count below 0000).
When the PWM goes into overcurrent, the counter rapidly
reaches count 1111 and the PWM output is shut down and
the soft-start counter is reset. After 16 clocks the PWM
output is enabled and the soft-start cycle is started.
If Vout exceeds the overvoltage limit for 32 consecutive clock
cycles the PWM output is shut off and the soft-start cycle is
initiated.
No Load Operation
If there is no load connected to the output, the converter will
regulate the output voltage by allowing the inductor current
to reverse for a short period of time.
Output Capacitor Selection
For best performance, a low ESR output capacitor is
needed. Output voltages below 1.8V require a larger output
capacitor and ESR value to improve the performance and
stability of the converter. For 1.8V output applications, a
ceramic capacitor of 10μF or higher value with ESR ≤ 50m ?
is recommended.
The RMS ripple current is calculated as:
Vo
Vin 1
L × f
L = the inductor value
f = the switching frequency
The overall output ripple voltage is the sum of the voltage spike
caused by the output capacitor ESR and the voltage ripple
caused by charge and discharge of the output capacitor:
Input Capacitor Selection
The input current to the buck converter is pulsed, and
therefore a low ESR input capacitor is required. This results
in good input voltage filtering and minimizes the interference
it causes to other circuits. The input capacitor should have a
minimum value of 10 μ F and a higher value can be selected
for improving input voltage filtering. The input capacitor
should be rated for the maximum input ripple current
calculated as:
Vo Vo
Vin ? Vin ?
The worst case RMS ripple current occurs at D = 0.5 and is
calculated as: Irms = Io/2.
D = Duty Cycle
Ceramic capacitors are preferred because of their low ESR
value. They are also less sensitive to voltage transients
when compared to tantalum capacitors. It is good practice to
place the input capacitor as close as possible to the input pin
of the IC for optimum performance.
Inductor Selection
The ISL6410 is an internally compensated device and hence
a minimum of 8.2 μ H must be used for the ISL6410 and a
minimum of 12 μ H for the ISL6410A. The selected inductor
must have a low DC resistance and a saturation current
greater than the maximum inductor current value can be
calculated from the equations below
Vo
Vin
L × f
-------- -
IL max = Io max + dIL
2
where
dIL = the peak to peak inductor current
L = the inductor value
f = the switching frequency
ILmax = the max inductor current
TABLE 3. RECOMMENDED INDUCTORS
COMPONENT
1 – ---------
? Vo = Vo × ------------------- × ? ------------------------- + ESR ?
Vo
Vin 1
L × f ? 8 × Co × f ?
Where the highest output voltage ripple occurs at the highest
input voltage VIN.
INDUCTOR VALUE
8.2 μ H
12 μ H
DCR (m ?)
75
100
SUPPLIER
Coilcraft
MSS6122-822MX
Coilcraft
MSS6122-123MX
TABLE 2. RECOMMENDED OUTPUT CAPACITORS
CAPACITOR
ESR
COMPONENT
VALUE
(m ?)
SUPPLIER
COMMENTS
10 μ F
<50 AVX 08056D106KAT2A
8
Ceramic
相关PDF资料
PDF描述
25ZLH560MEFC8X20 CAP ALUM 560UF 25V 20% RADIAL
RCC28DRYS CONN EDGECARD 56POS DIP .100 SLD
35JZV100M6.3X8 CAP ALUM 100UF 35V 20% SMD
UUR2A4R7MCL1GS CAP ALUM 4.7UF 100V 20% SMD
EL7530IYZ-T7 IC REG BUCK SYNC ADJ 0.6A 10MSOP
相关代理商/技术参数
参数描述
ISL6410IUZ-TKS2695 制造商:Intersil Corporation 功能描述:CONV DC-DC SGL-OUT STEP DOWN 3.3V-IN 10MSOP - Tape and Reel
ISL6411EVAL1 功能描述:EVALUATION BOARD ISL6411 RoHS:否 类别:编程器,开发系统 >> 过时/停产零件编号 系列:- 标准包装:1 系列:- 传感器类型:CMOS 成像,彩色(RGB) 传感范围:WVGA 接口:I²C 灵敏度:60 fps 电源电压:5.7 V ~ 6.3 V 嵌入式:否 已供物品:成像器板 已用 IC / 零件:KAC-00401 相关产品:4H2099-ND - SENSOR IMAGE WVGA COLOR 48-PQFP4H2094-ND - SENSOR IMAGE WVGA MONO 48-PQFP
ISL6411IR-TK 制造商:Rochester Electronics LLC 功能描述:- Bulk
ISL6412IR 功能描述:IC REG LDO 1.8V/2.8V/2.8V 16-QFN RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 标准包装:3,000 系列:- 稳压器拓扑结构:正,可调式 输出电压:1.2 V ~ 5.5 V 输入电压:1.7 V ~ 5.5 V 电压 - 压降(标准):0.075V @ 400mA 稳压器数量:1 电流 - 输出:400mA(最小值) 电流 - 限制(最小):400mA 工作温度:-55°C ~ 125°C 安装类型:表面贴装 封装/外壳:SC-74A,SOT-753 供应商设备封装:SOT-23-5 包装:带卷 (TR) 其它名称:296-20789-2V62/06626-01XE
ISL6412IR-T5K 功能描述:IC REG LDO 1.8V/2.8V/2.8V 16-QFN RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 标准包装:3,000 系列:- 稳压器拓扑结构:正,可调式 输出电压:1.2 V ~ 5.5 V 输入电压:1.7 V ~ 5.5 V 电压 - 压降(标准):0.075V @ 400mA 稳压器数量:1 电流 - 输出:400mA(最小值) 电流 - 限制(最小):400mA 工作温度:-55°C ~ 125°C 安装类型:表面贴装 封装/外壳:SC-74A,SOT-753 供应商设备封装:SOT-23-5 包装:带卷 (TR) 其它名称:296-20789-2V62/06626-01XE