- 您现在的位置：买卖IC网 > PDF目录19274 > ISL6412IR (Intersil)IC REG LDO 1.8V/2.8V/2.8V 16-QFN PDF资料下载
参数资料
| 型号： | ISL6412IR |
| 厂商： | Intersil |
| 文件页数： | 9/10页 |
| 文件大小： | 0K |
| 描述： | IC REG LDO 1.8V/2.8V/2.8V 16-QFN |
| 标准包装： | 75 |
| 稳压器拓扑结构： | 正，固定式 |
| 输出电压： | 1.8V，2.8V，2.8V |
| 输入电压： | 3 V ~ 3.6 V |
| 电压 - 压降（标准）： | -，0.125V @ 225mA，0.1V @ 125mA |
| 稳压器数量： | 3 |
| 电流 - 输出： | 330mA（最小），225mA（最小），125mA（最小） |
| 电流 - 限制（最小）： | 500mA，330mA，300mA |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-VQFN 裸露焊盘 |
| 供应商设备封装： | 16-QFN-EP（4x4） |
| 包装： | 管件 |
ISL6412
Thermal Overload Protection
Thermal overload protection limits total power dissipation in
FAULT Functionality
TABLE 1.
the ISL6412. When the junction temperature (T J ) exceeds
+150°C, the thermal sensor sends a signal to the shutdown
logic, turning off the pass transistor and allowing the IC to
cool. The pass transistor turns on again after the IC’s
junction temperature typically cools by 20°C, resulting in a
pulsed output during continuous thermal overload
conditions. Thermal overload protection protects the
ISL6412 against fault conditions. For continuous operation,
do not exceed the absolute maximum junction temperature
rating of +150°C.
Operating Region and Power Dissipation
The maximum power dissipation of ISL6412 depends on the
thermal resistance of the IC package and circuit board, the
EVENT
Below UVLO threshold
V OUT1 = 1.8V ±8% typ
V OUT2 /V OUT3 not in regulation
V OUT1 not in regulation
V OUT2 and V OUT3 are in regulation
Thermal Shutdown
Normal Shutdown with SHDN pin
Overcurrent only on LDO1
Overcurrent only on LDO2/LDO3
FAULT1
L
H
L
L
L
L
H
temperature difference between the die junction and ambient
air, and the rate of air flow. The power dissipated in the
device is:
PT = P1 + P2 + P3, where
P1 = I OUT1 (V IN – V OUT1 )
P2 = I OUT2 (V IN – V OUT2 )
P3 = I OUT3 (V IN - V OUT3 )
The maximum power dissipation is:
Pmax = (Tjmax – T A )/ θ JA
Where Tjmax = +150°C, T A = ambient temperature, and θ JA
is the thermal resistance from the junction to the surrounding
environment.
The ISL6412 package features an exposed thermal pad on
its underside. This pad lowers the thermal resistance of the
package by providing a direct heat conduction path from the
die to the PC board. Additionally, the ISL6412’s ground
(GND/GND3) performs the dual function of providing an
electrical connection to system ground and channeling heat
away. Connect the exposed backside pad and GND to the
system ground using a large pad or ground plane, or through
multiple vias to the ground plane layer.
Integrator Circuitry
The ISL6412 uses an external 33nF compensation capacitor
for minimizing load and line regulation errors and for
lowering output noise. When the output voltage shifts due to
varying load current or input voltage, the integrator capacitor
voltage is raised or lowered to compensate for the
systematic offset at the error amplifier. Compensation is
limited to ±5% to minimize transient overshoot when the
device goes out of dropout, current limit, or thermal
shutdown.
9
Applications Information
Capacitor Selection and Regulator Stability
Capacitors are required at the ISL6412’s input and output for
stable operation over the entire load range and the full
temperature range. Use >1μF capacitor at the input of
ISL6412. The input capacitor lowers the source impedance
of the input supply. Larger capacitor values and lower ESR
provides better PSRR and line transient response. The input
capacitor must be located at a distance of not more then 0.5
inches from the VIN pins of the IC and returned to a clean
analog ground. Any good quality ceramic or tantalum can be
used as an input capacitor.
The output capacitor must meet the requirements of
minimum amount of capacitance and ESR for all three
LDO’s. The ISL6412 is specifically designed to work with
small ceramic output capacitors. The output capacitor ’s ESR
affects stability and output noise. Use an output capacitor
with an ESR of 50m Ω or less to insure stability and optimum
transient response. For stable operation, a ceramic
capacitor, with a minimum value of 3.3 μ F, is recommended
for V OUT1 for 300mA output current, and 2.2 μ F is
recommended for V OUT2 and V OUT3 each at 200mA load
current. There is no upper limit to the output capacitor value.
Larger capacitor can reduce noise and improve load
transient response, stability and PSRR. Higher value of
output capacitor (10μF) is recommended for LDO3 when
used to power VCO circuitry in wireless chipsets. The output
capacitor should be located very close to VOUT pins to
minimize impact of PC board inductances and the other end
of the capacitor should be returned to a clean analog
ground.
Input-Output (Dropout) Voltage
A regulator ’s minimum input-output voltage differential (or
dropout voltage) determines the lowest usable supply
voltage. Because the ISL6412 uses a P-channel MOSFET
pass transistor, its dropout voltage is a function of r DS(ON)
(typically 0.5) multiplied by the load current.
FN9067.1
March 20, 2007
相关PDF资料 |
PDF描述 |
|---|---|
| VI-J11-CW-S | CONVERTER MOD DC/DC 12V 100W |
| AGM22DRMT-S664 | CONN EDGECARD 44POS .156 WW |
| VE-B12-CX-S | CONVERTER MOD DC/DC 15V 75W |
| AMM18DTKN-S288 | CONN EDGECARD 36POS .156 EXTEND |
| VI-B12-CX-S | CONVERTER MOD DC/DC 15V 75W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL6412IR-T5K | 功能描述:IC REG LDO 1.8V/2.8V/2.8V 16-QFN RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 标准包装:3,000 系列:- 稳压器拓扑结构:正，可调式 输出电压:1.2 V ~ 5.5 V 输入电压:1.7 V ~ 5.5 V 电压 - 压降（标准）:0.075V @ 400mA 稳压器数量:1 电流 - 输出:400mA（最小值） 电流 - 限制（最小）:400mA 工作温度:-55°C ~ 125°C 安装类型:表面贴装 封装/外壳:SC-74A，SOT-753 供应商设备封装:SOT-23-5 包装:带卷 (TR) 其它名称:296-20789-2V62/06626-01XE |
| ISL6412IR-TK | 功能描述:IC REG LDO 1.8V/2.8V/2.8V 16-QFN RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 标准包装:3,000 系列:- 稳压器拓扑结构:正，可调式 输出电压:1.2 V ~ 5.5 V 输入电压:1.7 V ~ 5.5 V 电压 - 压降（标准）:0.075V @ 400mA 稳压器数量:1 电流 - 输出:400mA（最小值） 电流 - 限制（最小）:400mA 工作温度:-55°C ~ 125°C 安装类型:表面贴装 封装/外壳:SC-74A，SOT-753 供应商设备封装:SOT-23-5 包装:带卷 (TR) 其它名称:296-20789-2V62/06626-01XE |
| ISL6412IRZ | 功能描述:低压差稳压器 - LDO VER OF ISL6412IR RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| ISL6412IRZ-TK | 功能描述:低压差稳压器 - LDO VER OF ISL6412IR-T 1 000 PC RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| ISL6413EVAL1 | 功能描述:EVALUATION BOARD ISL6413 RoHS:否 类别:编程器，开发系统 >> 过时/停产零件编号 系列:- 标准包装:1 系列:- 传感器类型:CMOS 成像，彩色（RGB） 传感范围:WVGA 接口:I²C 灵敏度:60 fps 电源电压:5.7 V ~ 6.3 V 嵌入式:否 已供物品:成像器板 已用 IC / 零件:KAC-00401 相关产品:4H2099-ND - SENSOR IMAGE WVGA COLOR 48-PQFP4H2094-ND - SENSOR IMAGE WVGA MONO 48-PQFP |
发布紧急采购，3分钟左右您将得到回复。