- 您现在的位置：买卖IC网 > PDF目录15196 > ISL6420AIRZ-TKR5264 (Intersil)IC REG CTRLR BUCK PWM VM 20-QFN PDF资料下载
参数资料
| 型号： | ISL6420AIRZ-TKR5264 |
| 厂商： | Intersil |
| 文件页数： | 15/21页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR BUCK PWM VM 20-QFN |
| 标准包装： | 1,000 |
| PWM 型： | 电压模式 |
| 输出数： | 1 |
| 频率 - 最大： | 1.4MHz |
| 占空比： | 100% |
| 电源电压： | 4.5 V ~ 28 V |
| 降压： | 是 |
| 升压： | 无 |
| 回扫： | 无 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 20-VFQFN 裸露焊盘 |
| 包装： | 带卷 (TR) |
ISL6420A
The slew time of the current is set by an external
capacitor on the CDEL pin, which is charged and
discharged with a 100μA current source. The change in
voltage on the capacitor is 2.5V. This same capacitor is
used to set the PGOOD active delay after soft-start.
When PGOOD is low, the internal PGOOD circuitry uses
the capacitor and when PGOOD is high, the voltage
margining circuit uses the capacitor. The slew time for
voltage margining can be in the range of 300μs to
2ms.
External Reference/DDR Supply
The voltage margining can be disabled by connecting
the VMSET/MODE to VCC5. In this mode, the chip can
be configured to work with an external reference input
and provide a buffered reference output.
If VMSET/MODE pin and the GPIO1/REFIN pin are both
tied to VCC5, then the internal 0.6V reference is used
as the error amplifier non-inverting input. The buffered
reference output on REFOUT will be 0.6V ±0.01V,
capable of sourcing 20mA and sinking up to 50μA
current with a 2.2μF capacitor connected to the
REFOUT pin.
If the VMSET/MODE pin is tied to high but
GPIO1/REFIN is connected to an external voltage
source between 0.6V to 1.25V, then this external
voltage is used as the reference voltage at the positive
input of the error amplifier. The buffered reference
output on REFOUT will be Vrefin ±0.01V, capable of
sourcing 20mA and sinking up to 50μA current with a
2.2μF capacitor on the REFOUT pin.
Power-Good
The PGOOD pin can be used to monitor the status of
the output voltage. PGOOD will be true (open drain)
when the FB pin is within ±10% of the reference and
the ENSS pin has completed its soft-start ramp.
Additionally, a capacitor on the CDEL pin will set a
delay for the PGOOD signal. After the ENSS pin
completes its soft-start ramp, a 2μA current begins
charging the CDEL capacitor to 2.5V. The capacitor will
be quickly discharged before PGOOD goes high. The
programmable delay can be used to sequence multiple
converters or as a LOW-true reset signal.
If the voltage on the FB pin exceeds ±10% of the
reference, then PGOOD will go low after 1μs of noise
filtering.
Over-Temperature Protection
The IC is protected against over-temperature
conditions. When the junction temperature exceeds
+150°C, the PWM shuts off. Normal operation is
resumed when the junction temperature is cooled
down to +130°C.
Shutdown
When ENSS pin is below 1V, the regulator is disabled
with the PWM output drivers tri-stated. When disabled,
the IC power will be reduced.
15
Undervoltage
If the voltage on the FB pin is less than 15% of the
reference voltage for 8 consecutive PWM cycles, then
the circuit enters into soft-start hiccup mode. This
mode is identical to the overcurrent hiccup mode.
Overvoltage Protection
If the voltage on the FB pin exceeds the reference
voltage by 15%, the lower gate driver is turned on
continuously to discharge the output voltage. If the
overvoltage condition continues for 32 consecutive
PWM cycles, then the chip is turned off with the gate
drivers tri-stated. The voltage on the FB pin will fall
and reach the 15% undervoltage threshold. After 8
clock cycles, the chip will enter soft-start hiccup
mode. This mode is identical to the overcurrent hiccup
mode.
Gate Control Logic
The gate control logic translates generated PWM
control signals into the MOSFET gate drive signals
providing necessary amplification, level shifting and
shoot-through protection. Also, it has functions that
help optimize the IC performance over a wide range of
operational conditions.
Since MOSFET switching time can vary dramatically
from type to type and with the input voltage, the gate
control logic provides adaptive dead time by
monitoring the gate-to-source voltages of both upper
and lower MOSFETs. The lower MOSFET is not turned
on until the gate-to-source voltage of the upper
MOSFET has decreased to less than approximately 1V.
Similarly, the upper MOSFET is not turned on until the
gate-to-source voltage of the lower MOSFET has
decreased to less than approximately 1V. This allows a
wide variety of upper and lower MOSFETs to be used
without a concern for simultaneous conduction, or
shoot-through.
Start-up into Pre-Biased Load
The ISL6420A is designed to power-up into a
pre-biased load. This is achieved by transitioning from
Diode Emulation mode to a Forced Continuous
Conduction mode during start-up. The lower gate turns
ON for a short period of time and the voltage on the
phase pin is sensed. When this goes negative the lower
gate is turned OFF and remains OFF till the next cycle.
As a result, the inductor current will not go negative
during soft-start and thus will not discharge the
pre-biased load. The waveform for this condition is
shown in Figure 14.
FN9169.4
December 4, 2009
相关PDF资料 |
PDF描述 |
|---|---|
| EB43-S0C3140W | CONN EDGEBOARD DUAL 62POS 3A |
| B43086A2686M | 68UF 200V 12.5X25 SINGLE END |
| SEK101M160ST | CAP ALUM 100UF 160V 20% RADIAL |
| VE-J4P-EW-F1 | CONVERTER MOD DC/DC 13.8V 100W |
| RCM31DRSI-S288 | CONN EDGECARD 62POS .156 EXTEND |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL6420AIRZ-TKS2698 | 制造商:Intersil Corporation 功能描述:PB-FREE W/ANNEAL SYNC BUCK PWM CONT. WITH 4.5V-28V INPUT,20L - Tape and Reel |
| ISL6420AIRZ-TKS2705 | 制造商:Intersil Corporation 功能描述:CISCO, ISL6420AIRZ-TK W/CONTAINER LABELING, SPECIAL CHANGE C - Rail/Tube |
| ISL6420BEVAL1Z | 功能描述:EVAL BOARD 1 FOR ISL6420B RoHS:是 类别:编程器，开发系统 >> 评估板 - DC/DC 与 AC/DC（离线）SMPS 系列:* 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:True Shutdown™ 主要目的:DC/DC，步升 输出及类型:1，非隔离 功率 - 输出:- 输出电压:- 电流 - 输出:1A 输入电压:2.5 V ~ 5.5 V 稳压器拓扑结构:升压 频率 - 开关:3MHz 板类型:完全填充 已供物品:板 已用 IC / 零件:MAX8969 |
| ISL6420BEVAL2Z | 功能描述:EVAL BOARD 2 FOR ISL6420B RoHS:是 类别:编程器，开发系统 >> 评估板 - DC/DC 与 AC/DC（离线）SMPS 系列:* 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:True Shutdown™ 主要目的:DC/DC，步升 输出及类型:1，非隔离 功率 - 输出:- 输出电压:- 电流 - 输出:1A 输入电压:2.5 V ~ 5.5 V 稳压器拓扑结构:升压 频率 - 开关:3MHz 板类型:完全填充 已供物品:板 已用 IC / 零件:MAX8969 |
| ISL6420BIAZ | 功能描述:IC REG CTRLR BUCK PWM VM 20-QSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:275kHz 占空比:50% 电源电压:18 V ~ 110 V 降压:无 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:是 工作温度:-40°C ~ 85°C 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。