- 您现在的位置：买卖IC网 > PDF目录15196 > ISL6420BIRZ-TK (Intersil)IC REG CTRLR BUCK PWM VM 20-QFN PDF资料下载
参数资料
| 型号： | ISL6420BIRZ-TK |
| 厂商： | Intersil |
| 文件页数： | 13/21页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR BUCK PWM VM 20-QFN |
| 标准包装： | 1,000 |
| PWM 型： | 电压模式 |
| 输出数： | 1 |
| 频率 - 最大： | 1.4MHz |
| 占空比： | 100% |
| 电源电压： | 4.5 V ~ 28 V |
| 降压： | 是 |
| 升压： | 无 |
| 回扫： | 无 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 20-VFQFN 裸露焊盘 |
| 包装： | 带卷 (TR) |
ISL6420B
TABLE 3. VOLTAGE MARGINING CONTROLLED BY
GPIO1 AND GPIO2
GPIO1
L
L
H
H
GPIO2
L
H
L
H
VOUT
No Change
+ Δ VOUT
- Δ VOUT
Ignored
V OUT
I OUT
PHASE
Functional Description
Initialization
The ISL6420B automatically initializes upon receipt of
power. The Power-On Reset (POR) function monitors
the internal bias voltage generated from LDO output
(VCC5) and the ENSS pin. The POR function initiates
the soft-start operation after the VCC5 exceeds the
POR threshold. The POR function inhibits operation
with the chip disabled (ENSS pin <1V).
The device can operate from an input supply voltage of
5.5V to 28V connected directly to the VIN pin using the
internal 5V linear regulator to bias the chip and supply
the gate drivers. For 5V ±10% applications, connect
VIN to VCC5 to bypass the linear regulator.
Soft-Start/Enable
The ISL6420B soft-start function uses an internal
current source and an external capacitor to reduce
stresses and surge current during start-up.
When the output of the internal linear regulator
reaches the POR threshold, the POR function initiates
the soft-start sequence. An internal 10μA current
source charges an external capacitor on the ENSS pin
linearly from 0V to 3.3V.
When the ENSS pin voltage reaches 1V typically, the
internal 0.6V reference begins to charge following the
dv/dt of the ENSS voltage. As the soft-start pin
charges from 1V to 1.6V, the reference voltage charges
from 0V to 0.6V. Figure 9 shows a typical soft-start
sequence.
V IN = 28V, V OUT = 3.3V, I OUT = 10A
ENSS
FIGURE 10. TYPICAL OVERCURRENT HICCUP MODE
Overcurrent Protection
The overcurrent function protects the converter from
a shorted output by using the upper MOSFET’s
ON-resistance, r DS(ON) to monitor the current. This
method enhances the converter’s efficiency and
reduces cost by eliminating a current sensing resistor.
The overcurrent function cycles the soft-start function
in a hiccup mode to provide fault protection. A resistor
connected to the drain of the upper FET and the
OCSET pin programs the overcurrent trip level. The
PHASE node voltage will be compared against the
voltage on the OCSET pin, while the upper FET is on.
A current (100μA typically) is pulled from the OCSET
pin to establish the OCSET voltage. If PHASE is lower
than OCSET while the upper FET is on then an
overcurrent condition is detected for that clock cycle.
The upper gate pulse is immediately terminated, and
a counter is incremented. If an overcurrent condition
is detected for 8 consecutive clock cycles, and the
circuit is not in soft-start, the ISL6420B enters into
the soft-start hiccup mode. During hiccup, the
external capacitor on the ENSS pin is discharged.
After the capacitor is discharged, it is released and a
soft-start cycle is initiated. There are three dummy
soft-start delay cycles to allow the MOSFETs to cool
down, to keep the average power dissipation in hiccup
mode at an acceptable level. At the fourth soft-start
cycle, the output starts a normal soft-start cycle, and
the output tries to ramp.
During soft-start, pulse termination current limiting is
enabled, but the 8-cycle hiccup counter is held in reset
until soft-start is completed. Figure 10 shows the
overcurrent hiccup mode.
The overcurrent function will trip at a peak inductor
current (I OC ) determined from Equation 1, where
I OCSET is the internal OCSET current source.
I OC = ---------------------------------------------------
I OCSET ? R OCSET
r DS ( ON )
(EQ. 1)
The OC trip point varies mainly due to the upper
MOSFETs r DS(ON) variations. To avoid overcurrent
tripping in the normal operating load range, find the
FIGURE 9. TYPICAL SOFT-START WAVEFORM
13
R OCSET resistor from Equation 1 with:
FN6901.1
December 4, 2009
相关PDF资料 |
PDF描述 |
|---|---|
| B41041C9337M | 330UF 100V 16X35.5 SINGLE END |
| SLPX391M200C1P3 | CAP ALUM 390UF 200V 20% SNAP |
| RCM31DRMI-S288 | CONN EDGECARD 62POS .156 EXTEND |
| B41042A5128M | 1200UF 25V 12.5X25 SINGLE END |
| VE-J4N-EW-F4 | CONVERTER MOD DC/DC 18.5V 100W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL6420BMAEP | 制造商:Intersil Corporation 功能描述:VOLT MODE PWM CNTRLR 20QSOP W - Rail/Tube |
| ISL6420BMAEP-TK | 制造商:Intersil Corporation 功能描述:VOLT MODE PWM CNTRLR 20QSOP W - Tape and Reel |
| ISL6420EVAL3 | 功能描述:EVALUATION BOARD 3 ISL6420 RoHS:否 类别:编程器，开发系统 >> 过时/停产零件编号 系列:- 标准包装:1 系列:- 传感器类型:CMOS 成像，彩色（RGB） 传感范围:WVGA 接口:I²C 灵敏度:60 fps 电源电压:5.7 V ~ 6.3 V 嵌入式:否 已供物品:成像器板 已用 IC / 零件:KAC-00401 相关产品:4H2099-ND - SENSOR IMAGE WVGA COLOR 48-PQFP4H2094-ND - SENSOR IMAGE WVGA MONO 48-PQFP |
| ISL6420IA | 功能描述:IC REG CTRLR BUCK PWM VM 20-QSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:4,000 系列:- PWM 型:电压模式 输出数:1 频率 - 最大:1.5MHz 占空比:66.7% 电源电压:4.75 V ~ 5.25 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 85°C 封装/外壳:40-VFQFN 裸露焊盘 包装:带卷 (TR) |
| ISL6420IA-TK | 功能描述:IC REG CTRLR BUCK PWM VM 20-QSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:4,000 系列:- PWM 型:电压模式 输出数:1 频率 - 最大:1.5MHz 占空比:66.7% 电源电压:4.75 V ~ 5.25 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 85°C 封装/外壳:40-VFQFN 裸露焊盘 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。