参数资料
| 型号： | ISL6423BERZ-T |
| 厂商： | Intersil |
| 文件页数： | 1/16页 |
| 文件大小： | 0K |
| 描述： | IC VREG SGL LNB W/I2C 24-QFN |
| 标准包装： | 6,000 |
| 应用： | 转换器，卫星信号接收机顶盒设计 |
| 输入电压： | 8 V ~ 14 V |
| 输出数： | 1 |
| 输出电压： | 13.3 V ~ 18.3 V，14.3 V ~ 19.3 V |
| 工作温度： | -20°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 24-VFQFN 裸露焊盘 |
| 供应商设备封装： | 24-QFN 裸露焊盘（4x4） |
| 包装： | 带卷 (TR) |
?
ISL6423B
Data Sheet
April 10, 2007
FN6412.1
Single Output LNB Supply and Control
Voltage Regulator with I 2 C Interface for
Advanced Satellite Set-Top Box Designs
The ISL6423B is a highly integrated voltage regulator and
interface IC, specifically designed for supplying power and
control signals from advanced satellite set-top box (STB)
modules to the low noise blocks (LNBs) of singe antenna
ports. The device consists of a current-mode boost PWM
and a low-noise linear regulator along with the circuitry
required for 22kHz tone generation, modulation and I 2 C
device interface. The device makes the total LNB supply
design simple, efficient and compact with low external
component count.
The current-mode boost converters provides the linear
regulator with input voltage that is set to the final output
voltages, plus typically 0.8V to insure minimum power
dissipation across each linear regulator. This maintains
constant voltage drop across the linear pass element while
permitting adequate voltage range for tone injection.
The final regulated output voltage is available at output
terminals to support the operation of an antenna port for
single tuners. The outputs for each PWM can be controlled
in two ways, full control from I 2 C using the VTOP and VBOT
bits or set the I 2 C to the lower range i.e., 13V/14V, and
switch to higher range i.e., 18V/19V, with the SELVTOP pin.
All the functions on this IC are controlled via the I 2 C bus by
writing 8 bits words onto the System Registers (SR). The
same register can be read back, and five I 2 C bits will report
the diagnostic status. Separate enable command sent on the
I 2 C bus provides for standby mode control for the PWM and
linear combination, disabling the output and forcing a shutdown
mode. The output channel is capable of providing 750mA of
continuous current. The overcurrent limit can be digitally
Features
? Single Chip Power solution
- Operation for 1-Tuner/1-Dish Applications
- Integrated DC/DC Converter and I 2 C Interface
? Switch-Mode Power Converter for Lowest Dissipation
- Boost PWMs with >92% Efficiency
- Selectable 13.3V or 18.3V Outputs
- Digital Cable Length Compensation (1V)
- I 2 C and Pin Controllable Output
? Output Back Bias Capability of 28V
? I 2 C Compatible Interface for Remote Device Control
? Registered Slave Address 0001 00XX
? 2.5V, 3.3V, 5V Logic Compatible
? External Pin to Toggle Between V and H Polarization
? Built-In Tone Oscillator Factory Trimmed to 22kHz
- Facilitates DiSEqC (EUTELSAT) Encoding
- External Modulation Input
? Internal Over-Temperature Protection and Diagnostics
? Internal OV, UV, Overload and Overtemp Flags
(Visible on I 2 C)
? FLT signal
? LNB Short-Circuit Protection and Diagnostics
? QFN, EPTSSOP Packages
? Pb-Free Available (RoHS Compliant)
Applications
? LNB Power Supply and Control for Satellite Set-Top Box
Ordering Information
programmed to four levels.
PART
PART
TEMP.
PKG.
The External modulation input EXTM can accept a
NUMBER*
MARKING
(°C)
PACKAGE
DWG. #
modulated Diseqc command and transfer it symmetrically to
the output. Alternatively the EXTM pin can be used to
ISL6423BERZ
(Note)
6423BERZ
-20 to +85 24 Ld 4x4 QFN
(Pb-free)
L24.4x4D
modulate the continuos internal tone.
ISL6423BEVEZ ISL6423BEVEZ -20 to +85 28 Ld EPTSSOP M28.173B
The FLT pin serves as an interrupt for the processor when
(Note)
(Pb-free)
any condition turns OFF the LNB controller (Over
Temperature, Overcurrent, Disabled). The nature of the
Disable can be read of the I 2 C registers.
NOTE: Intersil Pb-free plus anneal products employ special Pb-free
material sets; molding compounds/die attach materials and 100% matte
tin plate termination finish, which are RoHS compliant and compatible
with both SnPb and Pb-free soldering operations. Intersil Pb-free
products are MSL classified at Pb-free peak reflow temperatures that
meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020.
Add “-T” suffix for tape and reel.
1
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 1-888-468-3774 | Intersil (and design) is a registered trademark of Intersil Americas Inc.
Copyright Intersil Americas Inc. 2006, 2007. All Rights Reserved
All other trademarks mentioned are the property of their respective owners.
相关PDF资料 |
PDF描述 |
|---|---|
| ACM06DTBI | CONN EDGECARD 12POS R/A .156 SLD |
| EMM18DRSI | CONN EDGECARD 36POS DIP .156 SLD |
| HMM15DSUN | CONN EDGECARD 30POS .156 DIP SLD |
| HMM15DSUH | CONN EDGECARD 30POS .156 DIP SLD |
| EL7640ILTZ-T13 | IC BOOST REG DC/DC TFT-LCD 32QFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL6423BEVEZ | 功能描述:电流型 PWM 控制器 SINGLE LNB SUPPLY + CONTROL VAGEG W/I2C RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| ISL6423BEVEZ-T | 功能描述:电流型 PWM 控制器 SINGLE LNB SUPPLY + CONTROL VAGEG W/I2C RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| ISL6423ERZ | 功能描述:电流型 PWM 控制器 NOTCOMENDED FOR NEW DESIGN RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| ISL6423ERZ-T | 功能描述:电流型 PWM 控制器 NOTCOMENDED FOR NEW DESIGN RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| ISL6423EVEZ | 功能描述:电流型 PWM 控制器 NOTCOMENDED FOR NEW DESIGN RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
发布紧急采购，3分钟左右您将得到回复。