- 您现在的位置：买卖IC网 > PDF目录15180 > ISL6440IAZ (Intersil)IC REG CTRLR BUCK PWM CM 24-QSOP PDF资料下载
参数资料
| 型号： | ISL6440IAZ |
| 厂商： | Intersil |
| 文件页数： | 11/15页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR BUCK PWM CM 24-QSOP |
| 产品培训模块： | Solutions for Industrial Control Applications |
| 标准包装： | 1,000 |
| PWM 型： | 电流模式 |
| 输出数： | 2 |
| 频率 - 最大： | 340kHz |
| 占空比： | 93% |
| 电源电压： | 4.5 V ~ 24 V |
| 降压： | 是 |
| 升压： | 无 |
| 回扫： | 无 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 24-SSOP（0.154"，3.90mm 宽） |
| 包装： | 管件 |
ISL6440
F P = ------------------------------- = 600kHz
Over-Temperature Protection
The IC incorporates an over-temperature protection circuit
that shuts the IC down when a die temperature of 150°C is
reached. Normal operation resumes when the die
temperatures drops below 130°C through the initiation of a
1
2 π ? R 1 ? C 2
C2
full soft-start cycle.
R2
C1
Feedback Loop Compensation
To reduce the number of external components and to
simplify the process of determining compensation
components, both PWM controllers have internally
compensated error amplifiers. To make internal
compensation possible several design measures were
taken.
First, the ramp signal applied to the PWM comparator is
proportional to the input voltage provided via the VIN pin.
This keeps the modulator gain constant with variation in the
input voltage. Second, the load current proportional signal is
CONVERTER
EA
G M = 17.5dB
MODULATOR
F PO
F Z
R1
TYPE 2 EA
G EA = 18dB
F C
F P
R CS ≥ ---------------------------------------------
F PO = --------------------------------- ,
F Z = ------------------------------- = 6kHz
derived from the voltage drop across the lower MOSFET
during the PWM time interval and is subtracted from the
amplified error signal on the comparator input. This creates
an internal current control loop. The resistor connected to
the ISEN pin sets the gain in the current feedback loop. The
following expression estimates the required value of the
current sense resistor depending on the maximum operating
load current and the value of the MOSFET’s r DS(ON) .
( I MAX ) ( R DSon ) )
32 μ A
Choosing R CS to provide 32μA of current to the current
sample and hold circuitry is recommended at typical max
load levels, but values down to 2μA and up to 100μA can be
used.
Due to the current loop feedback, the modulator has a single
pole response with -20dB slope at a frequency determined
by the load.
1
2 π ? R O ? C O
where R O is load resistance and C O is load capacitance. For
this type of modulator, a Type 2 compensation circuit is
usually sufficient.
Figure 16 shows a Type 2 amplifier and its response along
with the responses of the current mode modulator and the
converter. The Type 2 amplifier, in addition to the pole at
origin, has a zero-pole pair that causes a flat gain region at
frequencies in between the zero and the pole.
1
2 π ? R 2 ? C 1
11
FIGURE 16. FEEDBACK LOOP COMPENSATION
The zero frequency, the amplifier high-frequency gain, and
the modulator gain are chosen to satisfy most typical
applications. The crossover frequency will appear at the
point where the modulator attenuation equals the amplifier
high frequency gain. The only task that the system designer
has to complete is to specify the output filter capacitors to
position the load main pole somewhere within one decade
lower than the amplifier zero frequency. With this type of
compensation plenty of phase margin is easily achieved due
to zero-pole pair phase ‘boost’.
Conditional stability may occur only when the main load pole
is positioned too much to the left side on the frequency axis
due to excessive output filter capacitance. In this case, the
ESR zero placed within the 1.2kHz to 30kHz range gives
some additional phase ‘boost’. Some phase boost can also
be achieved by connecting capacitor C Z in parallel with the
upper resistor R1 of the divider that sets the output voltage
value. Please refer to the output inductor and capacitor
selection sections for further details.
Layout Guidelines
Careful attention to layout requirements is necessary for
successful implementation of a ISL6440 based DC/DC
converter. The ISL6440 switches at a very high frequency
and therefore the switching times are very short. At these
switching frequencies, even the shortest trace has
significant impedance. Also the peak gate drive current rises
significantly in extremely short time. Transition speed of the
current from one device to another causes voltage spikes
across the interconnecting impedances and parasitic circuit
elements. These voltage spikes can degrade efficiency,
generate EMI, increase device overvoltage stress and
FN9040.2
October 4, 2005
相关PDF资料 |
PDF描述 |
|---|---|
| UPM1V152MHD6 | CAP ALUM 1500UF 35V 20% RADIAL |
| VI-B4J-EV-F2 | CONVERTER MOD DC/DC 36V 150W |
| GCC35DRTF-S13 | CONN EDGECARD 70POS .100 EXTEND |
| ESC22DRTS-S13 | CONN EDGECARD 44POS .100 EXTEND |
| ISL6520IBZ | IC REG CTRLR BUCK PWM VM 8-SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL6440IAZ-T | 功能描述:IC REG CTRLR BUCK PWM CM 24-QSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:75 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:1MHz 占空比:81% 电源电压:4.3 V ~ 13.5 V 降压:是 升压:是 回扫:是 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:0°C ~ 70°C 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:管件 产品目录页面:1051 (CN2011-ZH PDF) 其它名称:296-2543-5 |
| ISL6440IAZ-T7 | 功能描述:电流型 PWM 控制器 LEAD-FREE DUAL PWM CONTROLLER + LINEAR CONTROLLER, 300KHZ, 1 RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| ISL6440IAZ-TK | 功能描述:IC REG CTRLR BUCK PWM CM 24-QSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:275kHz 占空比:50% 电源电压:18 V ~ 110 V 降压:无 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:是 工作温度:-40°C ~ 85°C 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:带卷 (TR) |
| ISL6441IR | 功能描述:IC CTRLR SGL/STEP DOWN PWM 28QFN RoHS:否 类别:集成电路 (IC) >> PMIC - 电源管理 - 专用 系列:- 应用说明:Ultrasound Imaging Systems Application Note 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:37 系列:- 应用:医疗用超声波成像，声纳 电流 - 电源:- 电源电压:2.37 V ~ 6 V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:56-WFQFN 裸露焊盘 供应商设备封装:56-TQFN-EP（8x8） 包装:管件 |
| ISL6441IR-T | 功能描述:IC CTRLR PWM DUAL 1.4MHZ 28-QFN RoHS:否 类别:集成电路 (IC) >> PMIC - 电源管理 - 专用 系列:- 应用说明:Ultrasound Imaging Systems Application Note 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:37 系列:- 应用:医疗用超声波成像，声纳 电流 - 电源:- 电源电压:2.37 V ~ 6 V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:56-WFQFN 裸露焊盘 供应商设备封装:56-TQFN-EP（8x8） 包装:管件 |
发布紧急采购，3分钟左右您将得到回复。