- 您现在的位置：买卖IC网 > PDF目录22314 > ISL6521CB (Intersil)IC REG QD BCK/LINEAR 16-SOIC PDF资料下载
参数资料
| 型号： | ISL6521CB |
| 厂商： | Intersil |
| 文件页数： | 6/13页 |
| 文件大小： | 639K |
| 描述： | IC REG QD BCK/LINEAR 16-SOIC |
| 标准包装： | 48 |
| 拓扑： | 降压（降压）同步（1），线性（LDO）（3） |
| 功能： | 任何功能 |
| 输出数： | 4 |
| 频率 - 开关： | 300kHz |
| 电压/电流 - 输出 1： | 控制器 |
| 电压/电流 - 输出 2： | 可调式，120mA |
| 电压/电流 - 输出 3： | 可调式，120mA |
| 带 LED 驱动器： | 无 |
| 带监控器： | 无 |
| 带序列发生器： | 无 |
| 电源电压： | 4.5 V ~ 5.5 V |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | * |
| 封装/外壳： | 16-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | * |
| 包装： | 管件 |
| 产品目录页面： | 1243 (CN2011-ZH PDF) |
6
the clamped error amplifier output voltage. As the internal
soft-start voltage increases, the pulse-width on the PHASE
pin increases to reach its steady-state duty cycle at time T2.
Also at time T2, the error amplifier references of the linear
controllers, ramp to their final value bringing all outputs
within regulation limits.
Overcurrent Protection
All outputs are protected against excessive overcurrents.
The PWM controller uses the upper MOSFETs
on-resistance, r
DS(ON)
to monitor the current for protection
against a shorted output. All linear controllers monitor their
respective FB pins for undervoltage events to protect against
excessive currents.
A sustained overload (undervoltage on linears or overcurrent
on the PWM) on any output results in an independent
shutdown of the respective output, followed by subsequent
individual re-start attempts performed at an interval equivalent
to 3 soft-start intervals. Figure 2 describes the protection
feature. At time T0, an overcurrent event sensed across the
switching regulators upper MOSFET (r
DS(ON)
sensing)
triggers a shutdown of the V
OUT1
output. As a result, its
internal soft-start initiates a number of soft-start cycles. After a
three-cycle wait, the fourth soft-start initiates a ramp-up
attempt of the failed output, at time T2, bringing the output in
regulation at time T4.
To exemplify a UV event on one of the linears, at time T1,
the clock regulator (V
OUT2
) is also subjected to an
overcurrent event, resulting in a UV condition. Similarly, after
three soft-start periods, the fourth cycle initiates a ramp-up of
this linear output at time T3. One soft-start period after T3,
the linear output is within regulation limits. UV glitches less
than 1祍 (typically) in duration are ignored.
Overcurrent protection is performed on the synchronous
switching regulator on a cycle-by-cycle basis. OC monitoring
is active as long as the regulator is operational. Since the
overcurrent protection on the linear regulators is performed
through undervoltage monitoring at the feedback pins (FB2,
FB3, and FB4), this feature is activated approximately 25%
into the soft-start interval (see Figure 2).
A resistor (R
OCSET
) programs the overcurrent trip level for
the PWM converter. As shown in Figure 3, the internal
40礎 current sink (I
OCSET
) develops a voltage across
R
OCSET
(V
SET
) that is referenced to V
IN
. The DRIVE
signal enables the overcurrent comparator (OCC). When
the voltage across the upper MOSFET (V
DS(ON)
) exceeds
V
SET
, the overcurrent comparator trips to set the
overcurrent latch. Both V
SET
and V
DS(ON)
are referenced
to V
IN
and a small capacitor across R
OCSET
helps V
OCSET
track the variations of V
IN
due to MOSFET switching. The
overcurrent function will trip at a peak inductor current
(I
PEAK)
determined by:
FIGURE 1. SOFT-START INTERVAL
0V
0V
TIME
(0.5V/DIV)
V
OUT4
(3.3V)
V
OUT1
(1.5V)
T1
T2
T0
(1V/DIV)
V
OUT3
(1.8V)
V
OUT2
(2.5V)
+5V
FIGURE 2. OVERCURRENT/UNDERVOLTAGE PROTECTION
RESPONSE
0V
TIME
(0.5V/DIV.)
V
OUT3
(1.8V)
V
OUT2
(2.5V)
T1
T2
T3
T0
V
OUT4
(3.3V)
V
OUT1
(1.5V)
UV MONITORING
INACTIVE
SOFT-START
FUNCTION
ACTIVE
T4
V
OUT2
V
OUT1
I
PEAK
=
I
OCSET
R
OCSET
?/DIV>
r
DS ON
( )
----------------------------------------------------
ISL6521
相关PDF资料 |
PDF描述 |
|---|---|
| ECS-H1CC106R | CAP TANT 10UF 16V 20% 2312 |
| V300C48H75B2 | CONVERTER MOD DC/DC 48V 75W |
| V300C36H75BG3 | CONVERTER MOD DC/DC 36V 75W |
| ECS-H1CC685R | CAP TANT 6.8UF 16V 20% 2312 |
| MIC2548-2YMM | IC SW CURR LIMIT HI SIDE 8-MSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL6521CB-T | 功能描述:IC REG QD BCK/LINEAR 16-SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 + 切换式 系列:- 标准包装:2,500 系列:- 拓扑:降压（降压）同步（3），线性（LDO）（2） 功能:任何功能 输出数:5 频率 - 开关:300kHz 电压/电流 - 输出 1:控制器 电压/电流 - 输出 2:控制器 电压/电流 - 输出 3:控制器 带 LED 驱动器:无 带监控器:无 带序列发生器:是 电源电压:5.6 V ~ 24 V 工作温度:-40°C ~ 85°C 安装类型:* 封装/外壳:* 供应商设备封装:* 包装:* |
| ISL6521CBZ | 功能描述:电压模式 PWM 控制器 4 IN 1 PWM/LINEAR CNTRLR 5V RoHS:否 制造商:Texas Instruments 输出端数量:1 拓扑结构:Buck 输出电压:34 V 输出电流: 开关频率: 工作电源电压:4.5 V to 5.5 V 电源电流:600 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 封装 / 箱体:WSON-8 封装:Reel |
| ISL6521CBZA | 功能描述:电压模式 PWM 控制器 W/ANNEAL 4 IN 1 PWM/ LINEAR CNTRLR 5V RoHS:否 制造商:Texas Instruments 输出端数量:1 拓扑结构:Buck 输出电压:34 V 输出电流: 开关频率: 工作电源电压:4.5 V to 5.5 V 电源电流:600 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 封装 / 箱体:WSON-8 封装:Reel |
| ISL6521CBZA-T | 功能描述:电压模式 PWM 控制器 W/ANNEAL 4 IN 1 PWM/ LINEAR CNTRLR 5V RoHS:否 制造商:Texas Instruments 输出端数量:1 拓扑结构:Buck 输出电压:34 V 输出电流: 开关频率: 工作电源电压:4.5 V to 5.5 V 电源电流:600 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 封装 / 箱体:WSON-8 封装:Reel |
| ISL6521CBZS2698 | 功能描述:IC REG QD BCK/LINEAR 16-SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 + 切换式 系列:- 标准包装:2,500 系列:- 拓扑:降压（降压）同步（3），线性（LDO）（2） 功能:任何功能 输出数:5 频率 - 开关:300kHz 电压/电流 - 输出 1:控制器 电压/电流 - 输出 2:控制器 电压/电流 - 输出 3:控制器 带 LED 驱动器:无 带监控器:无 带序列发生器:是 电源电压:5.6 V ~ 24 V 工作温度:-40°C ~ 85°C 安装类型:* 封装/外壳:* 供应商设备封装:* 包装:* |
发布紧急采购，3分钟左右您将得到回复。