参数资料
| 型号： | ISL6531CB-T |
| 厂商： | Intersil |
| 文件页数： | 14/17页 |
| 文件大小： | 0K |
| 描述： | IC CONTROLLER INTEL 24SOIC |
| 标准包装： | 1,000 |
| 应用： | 控制器，Intel Pentium? III，IV |
| 输入电压： | 4.5 V ~ 5.5 V |
| 输出数： | 2 |
| 输出电压： | 2.5V |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 24-SOIC（0.295"，7.50mm 宽） |
| 供应商设备封装： | 24-SOIC |
| 包装： | 带卷 (TR) |
ISL6531
current (see the equations below). These equations assume
linear voltage-current transitions and do not adequately model
VCC
power loss due the reverse-recovery of the upper and lower
MOSFET’s body diode. The gate-charge losses are dissipated
by the ISL6531 and don't heat the MOSFETs. However, large
D BOOT
BOOTn
+
V D
-
V IN
P UPPER = Io × r DS ( ON ) × D + --- ? Io × V IN × t SW × f s
gate-charge increases the switching interval, t SW which
increases the MOSFET switching losses.
LOSSES WHILE SOURCING CURRENT
2 1
2
ISL6531
UGATEn
PHASEn
C BOOT
Q UPPER
NOTE:
V G-S ≈ V CC -V D
P LOWER = Io 2 x r DS(ON) x (1 - D)
LOSSES WHILE SINKING CURRENT
P UPPER = Io 2 x r DS(ON) x D
-
+
LGATEn
GND
Q LOWER
NOTE:
V G-S ≈ V CC
P LOWER = Io × r DS ( ON ) × ( 1 – D ) + --- ? Io × V IN × t SW × f s
C BOOT ≥ -----------------------------------------------------
2 1
2
Where: D is the duty cycle = V OUT / V IN ,
t SW is the combined switch ON and OFF time, and
f s is the switching frequency.
Ensure that both MOSFETs are within their maximum junction
temperature at high ambient temperature by calculating the
temperature rise according to package thermal-resistance
specifications. A separate heat sink may be necessary
depending upon MOSFET power, package type, ambient
temperature and air flow.
Given the reduced available gate bias voltage (5V), logic-
level or sub-logic-level transistors should be used for both N-
MOSFETs. Caution should be exercised when using devices
with very low gate thresholds (V TH ). The shoot-through
protection circuitry may be circumvented by these
MOSFETs. Very high dv/dt transitions on the phase node
may cause the Miller capacitance to couple the lower gate
with the phase node and cause an undesireable turn on of
the lower MOSFET while the upper MOSFET is on.
Bootstrap Component Selection
External bootstrap components, a diode and capacitor, are
required to provide sufficient gate enhancement to the upper
MOSFET. The internal MOSFET gate driver is supplied by
the external bootstrap circuitry as shown in Figure 10. The
boot capacitor, C BOOT , develops a floating supply voltage
referenced to the PHASE pin. This supply is refreshed each
cycle, when D BOOT conducts, to a voltage of VCC less the
boot diode drop, V D , plus the voltage rise across Q LOWER .
Just after the PWM switching cycle begins and the charge
transfer from the bootstrap capacitor to the gate capacitance
is complete, the voltage on the bootstrap capacitor is at its
lowest point during the switching cycle. The charge lost on
the bootstrap capacitor will be equal to the charge
transferred to the equivalent gate-source capacitance of the
upper MOSFET as shown:
Q GATE = C BOOT × ( V BOOT1 – V BOOT2 )
14
FIGURE 10. UPPER GATE DRIVE BOOTSTRAP
where Q GATE is the maximum total gate charge of the upper
MOSFET, C BOOT is the bootstrap capacitance, V BOOT1 is
the bootstrap voltage immediately before turn-on, and
V BOOT2 is the bootstrap voltage immediately after turn-on.
The bootstrap capacitor begins its refresh cycle when the
gate drive begins to turn-off the upper MOSFET. A refresh
cycle ends when the upper MOSFET is turned on again,
which varies depending on the switching frequency and
duty cycle.
The minimum bootstrap capacitance can be calculated by
rearranging the previous equation and solving for CBOOT.
Q GATE
V BOOT1 – V BOOT2
Typical gate charge values for MOSFETs considered in
these types of applications range from 20 to 100nC. Since
the voltage drop across Q LOWER is negligible, V BOOT1 is
simply VCC - V D . A schottky diode is recommended to
minimize the voltage drop across the bootstrap capacitor
during the on-time of the upper MOSFET. Initial calculations
with V BOOT2 no less than 4V will quickly help narrow the
bootstrap capacitor range.
For example, consider an upper MOSFET is chosen with a
maximum gate charge, Q g , of 100nC. Limiting the voltage
drop across the bootstrap capacitor to 1V results in a value
of no less than 0.1 μ F. The tolerance of the ceramic capacitor
should also be considered when selecting the final bootstrap
capacitance value.
A fast recovery diode is recommended when selecting a
bootstrap diode to reduce the impact of reverse recovery
charge loss. Otherwise, the recovery charge, Q RR , would
have to be added to the gate charge of the MOSFET and
taken into consideration when calculating the minimum
bootstrap capacitance.
相关PDF资料 |
PDF描述 |
|---|---|
| RMM28DRKI-S13 | CONN EDGECARD 56POS .156 EXTEND |
| X5165PI-2.7A | IC SUPERVISOR CPU 16K EE 8-DIP |
| X5165PI-2.7 | IC SUPERVISOR CPU 16K EE 8-DIP |
| ISL6530CR | IC CONTROLLER INTEL 32QFN |
| ACM25DRYI-S13 | CONN EDGECARD EXTEND 50POS 0.156 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL6531CBZ | 功能描述:IC CONTROLLER INTEL 24SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,000 系列:- 应用:电源，ICERA E400，E450 输入电压:4.1 V ~ 5.5 V 输出数:10 输出电压:可编程 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:42-WFBGA，WLCSP 供应商设备封装:42-WLP 包装:带卷 (TR) |
| ISL6531CBZ-T | 功能描述:IC CONTROLLER INTEL 24SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,000 系列:- 应用:电源，ICERA E400，E450 输入电压:4.1 V ~ 5.5 V 输出数:10 输出电压:可编程 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:42-WFBGA，WLCSP 供应商设备封装:42-WLP 包装:带卷 (TR) |
| ISL6531CR | 功能描述:IC CONTROLLER INTEL 32QFN RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,000 系列:- 应用:电源，ICERA E400，E450 输入电压:4.1 V ~ 5.5 V 输出数:10 输出电压:可编程 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:42-WFBGA，WLCSP 供应商设备封装:42-WLP 包装:带卷 (TR) |
| ISL6531CR-T | 功能描述:IC CONTROLLER INTEL 32QFN RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,000 系列:- 应用:电源，ICERA E400，E450 输入电压:4.1 V ~ 5.5 V 输出数:10 输出电压:可编程 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:42-WFBGA，WLCSP 供应商设备封装:42-WLP 包装:带卷 (TR) |
| ISL6531CRZ | 功能描述:IC CONTROLLER INTEL 32QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,000 系列:- 应用:电源，ICERA E400，E450 输入电压:4.1 V ~ 5.5 V 输出数:10 输出电压:可编程 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:42-WFBGA，WLCSP 供应商设备封装:42-WLP 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。