- 您现在的位置：买卖IC网 > PDF目录15171 > ISL6545AIRZ (Intersil)IC REG CTRLR BST PWM VM 10-DFN PDF资料下载
参数资料
| 型号： | ISL6545AIRZ |
| 厂商： | Intersil |
| 文件页数： | 6/16页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR BST PWM VM 10-DFN |
| 产品培训模块： | Solutions for Industrial Control Applications |
| 标准包装： | 100 |
| PWM 型： | 电压模式 |
| 输出数： | 1 |
| 频率 - 最大： | 660kHz |
| 占空比： | 100% |
| 电源电压： | 4.5 V ~ 14.4 V |
| 降压： | 是 |
| 升压： | 是 |
| 回扫： | 无 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 10-VFDFN 裸露焊盘 |
| 包装： | 管件 |
ISL6545, ISL6545A
Functional Description
Initialization (POR and OCP Sampling)
Figure 1 shows a simplified timing diagram. The
Power-On-Reset (POR) function continually monitors the
bias voltage at the VCC pin. Once the rising POR threshold
is exceeded (VPOR ~4V nominal), the POR function initiates
the Overcurrent Protection (OCP) sample and hold
soft-start operation is initiated, and the output voltage ramps
up between t4 and t5.
LGATE
STARTS
SWITCHING
COMP/SD (0.25V/DIV)
operation (while COMP/SD is ~1V). When the sampling is
complete, VOUT begins the soft-start ramp.
0.4V
If the COMP/SD pin is held low during power-up, that will just
delay the initialization until it is released, and the COMP/SD
voltage is above the V DISABLE trip point.
LGATE/OCSET (0.25V/DIV)
V OUT
(0.5V/DIV)
V CC (2V/DIV)
GND>
3.4ms
t0 t1
3.4ms
0 - 3.4ms
t2
t3 t4
6.8ms
t5
FIGURE 2. LGATE/OCSET AND SOFT-START OPERATION
Soft-Start and Pre-Biased Outputs
~4V POR
V OUT (1V/DIV)
COMP/SD (1V/DIV)
GND>
FIGURE 1. POR AND SOFT-START OPERATION
Figure 2 shows a typical power-up sequence in more detail.
The initialization starts at T0, when either V CC rises above
V POR , or the COMP/SD pin is released (after POR). The
COMP/SD will be pulled up by an internal 20μA current
source, but the timing will not begin until the COMP/SD
exceeds the V DISABLE trip point (at t1). The external
capacitance of the disabling device, as well as the
compensation capacitors, will determine how quickly the
20μA current source will charge the COMP/SD pin. With
typical values, it should add a small delay compared to the
soft-start times. The COMP/SD will continue to ramp to ~1V.
From t1, there is a nominal 6.8ms delay, which allows the
V CC pin to exceed 6.5V (if rising up towards 12V), so that
the internal bias regulator can turn on cleanly. At the same
time, the LGATE/OCSET pin is initialized, by disabling the
LGATE driver and drawing I OCSET (nominal 21.5μA)
through R OCSET . This sets up a voltage that will represent
the OCSET trip point. At t2, there is a variable time period for
the OCP sample and hold operation (0ms to 3.4ms nominal;
the longer time occurs with the higher overcurrent setting).
The sample and hold uses a digital counter and DAC to save
the voltage, so the stored value does not degrade, for as
long as the V CC is above V POR . See “Overcurrent Protection
variables. Upon the completion of sample and hold at t3, the
6
Functionally, the soft-start internally ramps the reference on
the non-inverting terminal of the error amp from 0V to 0.6V in
a nominal 6.8ms The output voltage will thus follow the
ramp, from zero to final value, in the same 6.8ms (the actual
ramp seen on the V OUT will be less than the nominal time,
due to some initialization timing, between t3 and t4).
The ramp is created digitally, so there will be 64 small
discrete steps. There is no simple way to change this ramp
rate externally, and it is the same for either frequency
version of the IC (300kHz or 600kHz).
After an initialization period (t3 to t4), the error amplifier
(COMP/SD pin) is enabled, and begins to regulate the
converter ’s output voltage during soft-start. The oscillator ’s
triangular waveform is compared to the ramping error
amplifier voltage. This generates PHASE pulses of
increasing width that charge the output capacitors. When the
internally generated soft-start voltage exceeds the reference
voltage (0.6V), the soft-start is complete, and the output
should be in regulation at the expected voltage. This method
provides a rapid and controlled output voltage rise; there is
no large inrush current charging the output capacitors. The
entire start-up sequence from POR typically takes up to
17ms; up to 10.2ms for the delay and OCP sample, and
6.8ms for the soft-start ramp.
Figure 3 shows the normal curve in blue; initialization begins
at t0, and the output ramps between t1 and t2. If the output is
pre-biased to a voltage less than the expected value, as
shown by the magenta curve, the ISL6545x will detect that
condition. Neither MOSFET will turn on until the soft-start
ramp voltage exceeds the output; V OUT starts seamlessly
ramping from there. If the output is pre-biased to a voltage
above the expected value, as in the red curve, neither
MOSFET will turn on until the end of the soft-start, at which
FN6305.6
March 3, 2011
相关PDF资料 |
PDF描述 |
|---|---|
| VI-J4M-EW-F4 | CONVERTER MOD DC/DC 10V 100W |
| VI-J4M-EW-F2 | CONVERTER MOD DC/DC 10V 100W |
| HIP6301CBZ | IC REG CTRLR BUCK PWM 20-SOIC |
| RCM24DTBT-S189 | CONN EDGECARD 48POS R/A .156 SLD |
| SLPX222M080A7P3 | CAP ALUM 2200UF 80V 20% SNAP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL6545AIRZ-T | 功能描述:IC REG CTRLR BST PWM VM 10-DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:275kHz 占空比:50% 电源电压:18 V ~ 110 V 降压:无 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:是 工作温度:-40°C ~ 85°C 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:带卷 (TR) |
| ISL6545CBZ | 功能描述:IC REG CTRLR BUCK PWM VM 8-SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:275kHz 占空比:50% 电源电压:18 V ~ 110 V 降压:无 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:是 工作温度:-40°C ~ 85°C 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:带卷 (TR) |
| ISL6545CBZS2698 | 功能描述:IC REG CTRLR BUCK PWM VM 8-SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:275kHz 占空比:50% 电源电压:18 V ~ 110 V 降压:无 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:是 工作温度:-40°C ~ 85°C 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:带卷 (TR) |
| ISL6545CBZ-T | 功能描述:IC REG CTRLR BUCK PWM VM 8-SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 特色产品:LM3753/54 Scalable 2-Phase Synchronous Buck Controllers 标准包装:1 系列:PowerWise® PWM 型:电压模式 输出数:1 频率 - 最大:1MHz 占空比:81% 电源电压:4.5 V ~ 18 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-5°C ~ 125°C 封装/外壳:32-WFQFN 裸露焊盘 包装:Digi-Reel® 产品目录页面:1303 (CN2011-ZH PDF) 其它名称:LM3754SQDKR |
| ISL6545CBZ-TS2694 | 功能描述:IC REG CTRLR BUCK PWM VM 8-SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 特色产品:LM3753/54 Scalable 2-Phase Synchronous Buck Controllers 标准包装:1 系列:PowerWise® PWM 型:电压模式 输出数:1 频率 - 最大:1MHz 占空比:81% 电源电压:4.5 V ~ 18 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-5°C ~ 125°C 封装/外壳:32-WFQFN 裸露焊盘 包装:Digi-Reel® 产品目录页面:1303 (CN2011-ZH PDF) 其它名称:LM3754SQDKR |
发布紧急采购，3分钟左右您将得到回复。