- 您现在的位置：买卖IC网 > PDF目录15194 > ISL6545CRZ-TS2694 (Intersil)IC REG CTRLR BUCK PWM VM 10-DFN PDF资料下载
参数资料
| 型号： | ISL6545CRZ-TS2694 |
| 厂商： | Intersil |
| 文件页数： | 13/16页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR BUCK PWM VM 10-DFN |
| 标准包装： | 6,000 |
| PWM 型： | 电压模式 |
| 输出数： | 1 |
| 频率 - 最大： | 330kHz |
| 占空比： | 100% |
| 电源电压： | 4.5 V ~ 14.4 V |
| 降压： | 是 |
| 升压： | 无 |
| 回扫： | 无 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | 0°C ~ 70°C |
| 封装/外壳： | 10-VFDFN 裸露焊盘 |
| 包装： | 带卷 (TR) |
ISL6545, ISL6545A
Minimizing the response time can minimize the output
capacitance required.
The response time to a transient is different for the
application of load and the removal of load. The equations in
Equation 11 give the approximate response time interval for
application and removal of a transient load:
switching losses seen when sinking current. When sourcing
current, the upper MOSFET realizes most of the switching
losses. The lower switch realizes most of the switching
losses when the converter is sinking current (see the
equations in Equation 12). These equations assume linear
voltage-current transitions and do not adequately model
power loss due the reverse-recovery of the upper and lower
t RISE =
L x I TRAN
V IN - V OUT
t FALL =
L x I TRAN
V OUT
(EQ. 11)
MOSFET’s body diode. The gate-charge losses are
dissipated by the ISL6545x and do not heat the MOSFETs.
However, large gate-charge increases the switching interval,
P UPPER = Io × r DS ( ON ) × D + --- ? Io × V IN × t SW × F S
where: I TRAN is the transient load current step, t RISE is the
response time to the application of load, and t FALL is the
response time to the removal of load. The worst case
response time can be either at the application or removal of
load. Be sure to check both of these equations at the
minimum and maximum output levels for the worst case
response time.
Input Capacitor Selection
Use a mix of input bypass capacitors to control the voltage
overshoot across the MOSFETs. Use small ceramic
capacitors for high frequency decoupling and bulk capacitors
t SW which increases the MOSFET switching losses. Ensure
that both MOSFETs are within their maximum junction
temperature at high ambient temperature by calculating the
temperature rise according to package thermal-resistance
specifications. A separate heatsink may be necessary
depending upon MOSFET power, package type, ambient
temperature and air flow.
Losses while Sourcing Current
2 1
2
P LOWER = Io 2 x r DS(ON) x (1 - D)
to supply the current needed each time Q 1 turns on. Place the
small ceramic capacitors physically close to the MOSFETs
Losses while Sinking Current
P UPPER = Io 2 x r DS(ON) x D
(EQ. 12)
P LOWER = Io × r DS ( ON ) × ( 1 – D ) + --- ? Io × V IN × t SW × F S
and between the drain of Q 1 and the source of Q 2 .
The important parameters for the bulk input capacitor are the
voltage rating and the RMS current rating. For reliable
operation, select the bulk capacitor with voltage and current
ratings above the maximum input voltage and largest RMS
current required by the circuit. The capacitor voltage rating
should be at least 1.25x greater than the maximum input
voltage and a voltage rating of 1.5x is a conservative
guideline. The RMS current rating requirement for the input
capacitor of a buck regulator is approximately 1/2 the DC
load current.
For a through-hole design, several electrolytic capacitors may
be needed. For surface mount designs, solid tantalum
capacitors can also be used, but caution must be exercised
with regard to the capacitor surge current rating. These
capacitors must be capable of handling the surge current at
power-up. Some capacitor series available from reputable
manufacturers are surge current tested.
MOSFET Selection/Considerations
The ISL6545x requires two N-Channel power MOSFETs.
These should be selected based upon r DS(ON) , gate supply
requirements, and thermal management requirements.
In high-current applications, the MOSFET power dissipation,
package selection and heatsink are the dominant design
factors. The power dissipation includes two loss components;
conduction loss and switching loss. The conduction losses are
the largest component of power dissipation for both the upper
and the lower MOSFETs. These losses are distributed between
the two MOSFETs according to duty factor. The switching
losses seen when sourcing current will be different from the
13
2 1
2
Where: D is the duty cycle = V OUT / V IN ,
t SW is the combined switch ON and OFF time, and
F SW is the switching frequency.
When operating with a 12V power supply for V CC (or down to a
minimum supply voltage of 6.5V), a wide variety of
N-MOSFETs can be used. Check the absolute maximum V GS
rating for both MOSFETs; it needs to be above the highest V CC
voltage allowed in the system; that usually means a 20V V GS
rating (which typically correlates with a 30V V DS maximum
rating). Low threshold transistors (around 1V or below) are not
recommended, for the reasons explained in the next
paragraph.
For 5V only operation, given the reduced available gate bias
voltage (5V), logic-level transistors should be used for both
N-MOSFETs. Look for r DS(ON) ratings at 4.5V. Caution
should be exercised with devices exhibiting very low
V GS(ON) characteristics. The shoot-through protection
present aboard the ISL6545x may be circumvented by these
MOSFETs if they have large parasitic impedences and/or
capacitances that would inhibit the gate of the MOSFET from
being discharged below its threshold level before the
complementary MOSFET is turned on. Also avoid MOSFETs
with excessive switching times; the circuitry is expecting
transitions to occur in under 50ns or so.
FN6305.6
March 3, 2011
相关PDF资料 |
PDF描述 |
|---|---|
| ISL88002IE26Z-TK | IC VOLT SUPERVISOR 2.63V SC-70 |
| ISL6545CRZ-T | IC REG CTRLR BUCK PWM VM 10-DFN |
| ISL6545ACRZ-T | IC REG CTRLR BST PWM VM 10-DFN |
| ISL88002IE17Z-TK | IC VOLT SUPERVISOR 1.67V SC-70 |
| ISL6520AIRZS2698 | IC REG CTRLR BUCK PWM VM 16-QFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL6545IBZ | 功能描述:IC REG CTRLR BUCK PWM VM 8-SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:75 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:1MHz 占空比:81% 电源电压:4.3 V ~ 13.5 V 降压:是 升压:是 回扫:是 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:0°C ~ 70°C 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:管件 产品目录页面:1051 (CN2011-ZH PDF) 其它名称:296-2543-5 |
| ISL6545IBZ-T | 功能描述:IC REG CTRLR BUCK PWM VM 8-SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 特色产品:LM3753/54 Scalable 2-Phase Synchronous Buck Controllers 标准包装:1 系列:PowerWise® PWM 型:电压模式 输出数:1 频率 - 最大:1MHz 占空比:81% 电源电压:4.5 V ~ 18 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-5°C ~ 125°C 封装/外壳:32-WFQFN 裸露焊盘 包装:Digi-Reel® 产品目录页面:1303 (CN2011-ZH PDF) 其它名称:LM3754SQDKR |
| ISL6545IRZ | 功能描述:IC REG CTRLR BUCK PWM VM 10-DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:275kHz 占空比:50% 电源电压:18 V ~ 110 V 降压:无 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:是 工作温度:-40°C ~ 85°C 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:带卷 (TR) |
| ISL6545IRZ-T | 功能描述:IC REG CTRLR BUCK PWM VM 10-DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:275kHz 占空比:50% 电源电压:18 V ~ 110 V 降压:无 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:是 工作温度:-40°C ~ 85°C 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 包装:带卷 (TR) |
| ISL6546IRZ | 功能描述:IC REG BUCK SYNC 1.2A 10-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:3.3V 输入电压:4.5 V ~ 24 V PWM 型:- 频率 - 开关:- 电流 - 输出:125mA 同步整流器:无 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-6 包装:Digi-Reel® 供应商设备封装:SOT-6 其它名称:MAX1836EUT33#TG16DKR |
发布紧急采购，3分钟左右您将得到回复。