- 您现在的位置：买卖IC网 > PDF目录17308 > ISL6548A-6506EVAL1Z (Intersil)EVALUATION BOARD ISL6548A-6506 PDF资料下载
参数资料
| 型号： | ISL6548A-6506EVAL1Z |
| 厂商： | Intersil |
| 文件页数： | 7/8页 |
| 文件大小： | 0K |
| 描述： | EVALUATION BOARD ISL6548A-6506 |
| 标准包装： | 1 |
| 主要目的： | 特殊用途 DC/DC，DDR 存储器电源 |
| 输出及类型： | 7，非隔离 |
| 功率 - 输出： | 178W |
| 输出电压： | 1.8V，3.3V，5V，1.5V，1.2V，2.5V，0.9V |
| 电流 - 输出： | 15A，14A，14A，10A，5A，5A，2A |
| 输入电压： | 3.3V，5V，12V |
| 稳压器拓扑结构： | 降压 |
| 板类型： | 完全填充 |
| 已供物品： | 板 |
| 已用 IC / 零件： | ISL6506，ISL6548A |
ISL6506, ISL6506A, ISL6506B
current demands. Thus, it is recommended that the output
capacitors be selected for transient load regulation, paying
attention to their parasitic components (ESR, ESL).
Also, during the transition between active and sleep states
on the 5V DUAL output, there is a short interval of time during
which none of the power pass elements are conducting.
During this time the output capacitors have to supply all the
output current. The output voltage drop during this brief
Transistor Selection/Considerations
The ISL6506, ISL6506A usually requires one P-Channel and
two N-Channel MOSFETs. All three of these MOSFETs are
utilized as ON/OFF switching elements.
One important criteria for selection of transistors for all the
switching elements is package selection for efficient removal
of heat. The power dissipated in a switch element while on is
shown in Equation 2:
Δ V OUT = I OUT × ? ESR OUT + ---------------- ?
P LOSS = I o × r DS ( ON )
period of time can be easily approximated using Equation 1:
? t t ?
(EQ. 1)
? C OUT ?
2
(EQ. 2)
where:
Δ V OUT = output voltage drop
ESR OUT = output capacitor bank ESR
I OUT = output current during transition
C OUT = output capacitor bank capacitance
t t = active-to-sleep/sleep-to-active transition time (10μs
typical)
The output voltage drop is heavily dependent on the ESR
Select a package and heatsink that maintains the junction
temperature below the rating with the maximum expected
ambient temperature.
Q1, Q3
These N-Channel MOSFETs are used to switch the 3.3V and
5V inputs provided by the ATX supply into the 3.3V AUX and
5V DUAL outputs while in active (S0, S1) state. The main
criteria for the selection of these transistors is output voltage
budgeting. The maximum r DS(ON) allowed at highest junction
temperature can be expressed using Equation 3:
r DS ( ON ) max = ---------------------------------------------------
(equivalent series resistance) of the output capacitor bank,
the choice of capacitors should be such as to maintain the
V INmin – V OUTmin
I OUTmax
(EQ. 3)
output voltage above the lowest allowable regulation level.
where:
Input Capacitors Selection
The input capacitors for an ISL6506, ISL6506A application
must have a sufficiently low ESR so as not to allow the input
voltage to dip excessively when energy is transferred to the
output capacitors. If the ATX supply does not meet the
specifications, certain imbalances between the ATX’s
outputs and the ISL6506, ISL6506A’s regulation levels could
have as a result a brisk transfer of energy from the input
capacitors to the supplied outputs. At the transition between
active and sleep states, such phenomena could be
responsible for the 5V SB voltage drooping excessively and
affecting the output regulation. The solution to such a
potential problem is using larger input capacitors with a
lower total combined ESR.
7
V INmin = minimum input voltage
V OUTmin = minimum output voltage allowed
I OUTmax = maximum output current
Q2
This is a P-Channel MOSFET used to switch the 5V SB
output of the ATX supply into the 5V DUAL output during
sleep states. The selection criteria of this device, as with the
N-Channel MOSFETs, is proper voltage budgeting. The
maximum r DS(ON) , however, has to be achieved with only
4.5V of gate-to-source voltage, so a true logic level
MOSFET needs to be selected.
FN9141.6
September 12, 2013
相关PDF资料 |
PDF描述 |
|---|---|
| 195D105X9015C2T | CAP TANT 1UF 15V 10% 0905 |
| 195D105X06R3C2T | CAP TANT 1UF 6.3V 20% 0905 |
| ECC20DREH-S13 | CONN EDGECARD 40POS .100 EXTEND |
| 195D105X0020C2T | CAP TANT 1UF 20V 20% 0905 |
| 195D105X0016C2T | CAP TANT 1UF 16V 20% 0905 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL6548ACRZA | 功能描述:电压模式 PWM 控制器 W/ANNEAL 5-IN-1G FOR DDR/I915/925LAKEPORT RoHS:否 制造商:Texas Instruments 输出端数量:1 拓扑结构:Buck 输出电压:34 V 输出电流: 开关频率: 工作电源电压:4.5 V to 5.5 V 电源电流:600 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 封装 / 箱体:WSON-8 封装:Reel |
| ISL6548ACRZA-T | 功能描述:电压模式 PWM 控制器 W/ANNEAL 5-IN-1G FOR DDR/I915/925LAKEPORT RoHS:否 制造商:Texas Instruments 输出端数量:1 拓扑结构:Buck 输出电压:34 V 输出电流: 开关频率: 工作电源电压:4.5 V to 5.5 V 电源电流:600 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 封装 / 箱体:WSON-8 封装:Reel |
| ISL6548CRZA | 功能描述:电压模式 PWM 控制器 W/ANNEAL 4-IN-1G FOR DDR/I915/925 RoHS:否 制造商:Texas Instruments 输出端数量:1 拓扑结构:Buck 输出电压:34 V 输出电流: 开关频率: 工作电源电压:4.5 V to 5.5 V 电源电流:600 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 封装 / 箱体:WSON-8 封装:Reel |
| ISL6548CRZA-T | 功能描述:电压模式 PWM 控制器 W/ANNEAL 4-IN-1G FOR DDR/I915/925 RoHS:否 制造商:Texas Instruments 输出端数量:1 拓扑结构:Buck 输出电压:34 V 输出电流: 开关频率: 工作电源电压:4.5 V to 5.5 V 电源电流:600 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 封装 / 箱体:WSON-8 封装:Reel |
| ISL6549CA | 功能描述:IC REG DL BCK/LINEAR 16-QSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 + 切换式 系列:- 标准包装:2,500 系列:- 拓扑:降压（降压）同步（3），线性（LDO）（2） 功能:任何功能 输出数:5 频率 - 开关:300kHz 电压/电流 - 输出 1:控制器 电压/电流 - 输出 2:控制器 电压/电流 - 输出 3:控制器 带 LED 驱动器:无 带监控器:无 带序列发生器:是 电源电压:5.6 V ~ 24 V 工作温度:-40°C ~ 85°C 安装类型:* 封装/外壳:* 供应商设备封装:* 包装:* |
发布紧急采购，3分钟左右您将得到回复。