参数资料
| 型号： | ISL6556BCB |
| 厂商： | Intersil |
| 文件页数： | 17/24页 |
| 文件大小： | 0K |
| 描述： | IC CTRLR MULTIPHASE VRM10 28SOIC |
| 标准包装： | 26 |
| 应用： | 控制器，Intel VR10X |
| 输入电压： | 3 V ~ 12 V |
| 输出数： | 4 |
| 输出电压： | 0.84 V ~ 1.6 V |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-SOIC（0.295"，7.50mm 宽） |
| 供应商设备封装： | 28-SOIC W |
| 包装： | 管件 |
ISL6556B
PGOOD will return high unless the controller has been
disabled. PGOOD does not automatically transition low upon
detection of an overvoltage condition.
Undervoltage Detection
The undervoltage threshold is set at 75% of the VID code.
When the output voltage at VSEN is below the undervoltage
threshold, PGOOD gets pulled low.
Overvoltage Protection
When VCC is above 1.4V, but otherwise not valid as defined
under Power on Reset in Electrical Specifications , the
overvoltage trip circuit is active using auxiliary circuitry. In
this state, an overvoltage trip occurs if the voltage at VSEN
exceeds 1.8V.
With valid VCC, the overvoltage circuit is sensitive to the
voltage at VDIFF. In this state, the trip level is 1.7V prior to
valid enable conditions being met as described in Enable
and Disable . The only exception to this is when the IC has
been disabled by an overvoltage trip. In that case the
overvoltage trip point is VID plus 200mV. During soft-start,
the overvoltage trip level is the higher of 1.7V or VID plus
200mV. Upon successful soft-start, the overvoltage trip level
is 200mV above VID. Two actions are taken by the ISL6556B
to protect the microprocessor load when an overvoltage
condition occurs.
At the inception of an overvoltage event, all PWM outputs
are commanded low until the voltage at VSEN falls below
0.6V with valid VCC or 1.5V otherwise. This causes the
Intersil drivers to turn on the lower MOSFETs and pull the
output voltage below a level that might cause damage to the
load. The PWM outputs remain low until VDIFF falls to the
programmed DAC level when they enter a high-impedance
state. The Intersil drivers respond to the high-impedance
input by turning off both upper and lower MOSFETs. If the
overvoltage condition reoccurs, the ISL6556B will again
command the lower MOSFETs to turn on. The ISL6556B will
continue to protect the load in this fashion as long as the
overvoltage condition recurs.
Simultaneous to the protective action of the PWM outputs, the
OVP pin pulls to VCC delivering up to 100mA to the gate of a
crowbar MOSFET or SCR placed either on the input rail or the
output rail. Turning on the MOSFET or SCR collapses the
power rail and causes a fuse placed further up stream to blow.
The fuse must be sized such that the MOSFET or SCR will
not overheat before the fuse blows. The OVP pin is tolerant to
12V (see Absolute Maximum Ratings ), so an external resistor
pull up can be used to augment the driving capability. If using
a pull up resistor in conjunction with the internal overvoltage
protection function, care must be taken to avoid nuisance trips
voltage on EN or ENLL or VCC below the POR-falling
threshold will reset the controller. Cycling the VID codes will
not reset the controller.
Overcurrent Protection
ISL6556B has two levels of overcurrent protection. Each
phase is protected from a sustained overcurrent condition on
a delayed basis, while the combined phase currents are
protected on an instantaneous basis.
In instantaneous protection mode, the ISL6556B takes
advantage of the proportionality between the load current
and the average current, I AVG , to detect an overcurrent
condition. See the Channel-Current Balance section for
more detail on how the average current is measured. The
average current is continually compared with a constant
100 μ A reference current as shown in Figure 10. Once the
average current exceeds the reference current, a comparator
triggers the converter to shutdown.
In individual overcurrent protection mode, the ISL6556B
continuously compares the current of each channel with the
same 100 μ A reference current. If any channel current exceeds
the reference current continuously for eight consecutive cycles,
the comparator triggers the converter to shutdown.
At the beginning of overcurrent shutdown, the controller
places all PWM signals in a high-impedance state
commanding the Intersil MOSFET driver ICs to turn off both
upper and lower MOSFETs. The system remains in this
state a period of 4096 switching cycles. If the controller is still
enabled at the end of this wait period, it will attempt a soft-
start. If the fault remains, the trip-retry cycles will continue
indefinitely (as shown in Figure 11) until either controller is
disabled or the fault is cleared. Note that the energy
delivered during trip-retry cycling is much less than during
full-load operation, so there is no thermal hazard during this
kind of operation.
OUTPUT CURRENT, 50A/DIV
0A
OUTPUT VOLTAGE,
500mV/DIV
that could occur when VCC is below 2V. In that case, the
controller is incapable of holding OVP low.
0V
2ms/DIV
Once an overvoltage condition is detected, normal PWM
operation ceases until the ISL6556B is reset. Cycling the
17
FIGURE 11. OVERCURRENT BEHAVIOR IN HICCUP MODE.
F SW = 500kHz
FN9097.4
December 28, 2004
相关PDF资料 |
PDF描述 |
|---|---|
| X5165V14-4.5A | IC SUPERVISOR CPU 16K EE 14TSSOP |
| X5165V14-2.7T1 | IC SUPERVISOR CPU 16K EE 14TSSOP |
| EEV-FC1C331P | CAP ALUM 330UF 16V 20% SMD |
| X5168P-2.7 | IC SUPERVISOR CPU 16K EE 8-DIP |
| FMC08DRXN | CONN EDGECARD 16POS DIP .100 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL6556BCB-T | 功能描述:IC CTRLR MULTIPHASE VRM10 28SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,000 系列:- 应用:电源，ICERA E400，E450 输入电压:4.1 V ~ 5.5 V 输出数:10 输出电压:可编程 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:42-WFBGA，WLCSP 供应商设备封装:42-WLP 包装:带卷 (TR) |
| ISL6556BCBZ | 功能描述:电流型 PWM 控制器 VRM 10 0 MULTI-PHS CONTROLLER RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| ISL6556BCBZ | 制造商:Intersil Corporation 功能描述:Pulse Width Modulation (PWM) Controller |
| ISL6556BCBZ-T | 功能描述:电流型 PWM 控制器 VRM 10 0 MULTI-PHS CONTROLLER RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| ISL6556BCR | 功能描述:IC CTRLR MULTIPHASE VRM10 32-QFN RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,000 系列:- 应用:电源，ICERA E400，E450 输入电压:4.1 V ~ 5.5 V 输出数:10 输出电压:可编程 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:42-WFBGA，WLCSP 供应商设备封装:42-WLP 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。