- 您现在的位置：买卖IC网 > PDF目录15176 > ISL6611AIRZ-T (Intersil)IC REG CTRLR DOUBLER PWM 16-QFN PDF资料下载
参数资料
| 型号： | ISL6611AIRZ-T |
| 厂商： | Intersil |
| 文件页数： | 1/14页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR DOUBLER PWM 16-QFN |
| 标准包装： | 6,000 |
| PWM 型： | 控制器 |
| 输出数： | 2 |
| 频率 - 最大： | 1MHz |
| 电源电压： | 4.5 V ~ 5.5 V |
| 降压： | 无 |
| 升压： | 无 |
| 回扫： | 无 |
| 反相： | 无 |
| 倍增器： | 是 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 16-VQFN 裸露焊盘 |
| 包装： | 带卷 (TR) |
?
ISL6611A
Data Sheet
August 28, 2012
FN6881.1
Phase Doubler with Integrated Drivers
and Phase Shedding Function
The ISL6611A utilizes Intersil’s proprietary Phase Doubler
scheme to modulate two-phase power trains with single
PWM input. It doubles the number of phases that Intersil’s
ISL63xx multiphase controllers can support. At the same
time, the PWM line can be pulled high to disable the
corresponding phase or higher phase(s) when the enable
pin (EN_PH) is pulled low. This simplifies the phase
shedding implementation. For layout simplicity and
improving system performance, the device integrates two 5V
drivers (ISL6609) and current balance function.
The ISL6611A is designed to minimize the number of analog
signals interfacing between the controller and drivers in high
phase count and scalable applications. The common COMP
signal, which is usually seen with conventional cascaded
configuration, is not required; this improves noise immunity
and simplifies the layout. Furthermore, the ISL6611A
provides low part count and a low cost advantage over the
conventional cascaded technique.
The IC is biased by a single low voltage supply (5V),
minimizing driver switching losses in high MOSFET gate
capacitance and high switching frequency applications.
Bootstrapping of the upper gate driver is implemented via an
internal low forward drop diode, reducing implementation
cost, complexity, and allowing the use of higher
performance, cost effective N-Channel MOSFETs. Adaptive
shoot-through protection is integrated to prevent both
MOSFETs from conducting simultaneously.
The ISL6611A features 4A typical sink current for the lower
gate driver, enhancing the lower MOSFET gate hold-down
capability during PHASE node rising edge, preventing power
loss caused by the self turn-on of the lower MOSFET due to
the high dV/dt of the switching node.
The ISL6611A also features an input that recognizes a
high-impedance state, working together with Intersil
multiphase PWM controllers to prevent negative transients
on the controlled output voltage when operation is
suspended. This feature eliminates the need for the Schottky
diode that may be utilized in a power system to protect the
load from negative output voltage damage.
In addition, the ISL6611A’s bootstrap function is designed to
prevent the BOOT capacitor from overcharging, should
excessively large negative swings occur at the transitions of
the PHASE node.
Features
? Proprietary Phase Doubler Scheme with Phase Shedding
Function (Patent Pending)
- Enhanced Light to Full Load Efficiency
? Patented Current Balancing with r DS(ON) Current Sensing
and Adjustable Gain
? Quad MOSFET Drives for Two Synchronous Rectified
Bridge with Single PWM Input
? Channel Synchronization and Interleaving Options
? Adaptive Zero Shoot-Through Protection
? 0.4 Ω On-Resistance and 4A Sink Current Capability
? 36V Internal Bootstrap Schottky Diode
? Bootstrap Capacitor Overcharging Prevention (ISL6611A)
? Supports High Switching Frequency (Up to 1MHz)
- Fast Output Rise and Fall
? Tri-State PWM Input for Output Stage Shutdown
? Phase Enable Input and PWM Forced High Output to
Interface with Intersil’s Controller for Phase Shedding
? QFN Package
- Compliant to JEDEC PUB95 MO-220 QFN-Quad Flat
No Leads-Product Outline
- Near Chip-Scale Package Footprint; Improves PCB
Utilization, Thinner Profile
- Pb-Free (RoHS Compliant)
Applications
? High Current Low Voltage DC/DC Converters
? High Frequency and High Efficiency VRM and VRD
? High Phase Count and Phase Shedding Applications
Related Literature
? Technical Brief TB363 “Guidelines for Handling and
Processing Moisture Sensitive Surface Mount Devices
(SMDs)”
1
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 1-888-468-3774 | Intersil (and design) is a registered trademark of Intersil Americas Inc.
Copyright Intersil Americas Inc. 2009, 2012. All Rights Reserved
All other trademarks mentioned are the property of their respective owners.
相关PDF资料 |
PDF描述 |
|---|---|
| VI-B4P-EV-F3 | CONVERTER MOD DC/DC 13.8V 150W |
| SDH3812-151-R | INDUCT SHIELD HP L-PRO 150UH SMD |
| ISL8106CRZ | IC REG CTRLR BUCK PWM VM 16-QFN |
| VI-B4P-EV-F2 | CONVERTER MOD DC/DC 13.8V 150W |
| SDH3812-150-R | INDUCTR SHIELD HP L-PRO 15UH SMD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL6612ACB | 功能描述:IC MOSFET DRVR SYNC BUCK 8-SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - MOSFET，电桥驱动器 - 外部开关 系列:- 标准包装:50 系列:- 配置:低端 输入类型:非反相 延迟时间:40ns 电流 - 峰:9A 配置数:1 输出数:1 高端电压 - 最大（自引导启动）:- 电源电压:4.5 V ~ 35 V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:TO-263-6，D²Pak（5 引线+接片），TO-263BA 供应商设备封装:TO-263 包装:管件 |
| ISL6612ACB-T | 功能描述:IC MOSFET DRVR SYNC BUCK 8-SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - MOSFET，电桥驱动器 - 外部开关 系列:- 标准包装:50 系列:- 配置:低端 输入类型:非反相 延迟时间:40ns 电流 - 峰:9A 配置数:1 输出数:1 高端电压 - 最大（自引导启动）:- 电源电压:4.5 V ~ 35 V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:TO-263-6，D²Pak（5 引线+接片），TO-263BA 供应商设备封装:TO-263 包装:管件 |
| ISL6612ACBZ | 功能描述:IC DRIVER MOSFET SYNC BUCK 8SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - MOSFET，电桥驱动器 - 外部开关 系列:- 标准包装:95 系列:- 配置:高端和低端，独立 输入类型:非反相 延迟时间:160ns 电流 - 峰:290mA 配置数:1 输出数:2 高端电压 - 最大（自引导启动）:600V 电源电压:10 V ~ 20 V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 供应商设备封装:8-SOIC 包装:管件 产品目录页面:1381 (CN2011-ZH PDF) |
| ISL6612ACBZA | 功能描述:IC MOSFET DRVR SYNC BUCK 8-SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - MOSFET，电桥驱动器 - 外部开关 系列:- 标准包装:6,000 系列:* |
| ISL6612ACBZAR5214 | 功能描述:IC MOSFET DRVR SYNC BUCK 8-SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - MOSFET，电桥驱动器 - 外部开关 系列:- 标准包装:6,000 系列:* |
发布紧急采购，3分钟左右您将得到回复。