- 您现在的位置：买卖IC网 > PDF目录383139 > ISL6AHPEVAL1 (Intersil Corporation) Dual Power Supply Controller PDF资料下载
参数资料
| 型号： | ISL6AHPEVAL1 |
| 厂商： | Intersil Corporation |
| 英文描述： | Dual Power Supply Controller |
| 中文描述： | 双电源控制器 |
| 文件页数： | 7/10页 |
| 文件大小： | 454K |
| 代理商： | ISL6AHPEVAL1 |
7
Using the ISL6118EVAL1 Platform
Upon proper bias the PPTC, F1, has a nominal 400mA load
current passing through it which is the hold current rating for
that particular device. Removal of the PPTC is necessary to
isolate the ISL6118 as the PPTC load current is common to
the ISL6118EVAL1 bias connections.
By enabling either or both of the ISL6118H switches by
signaling TP3 and/or TP4 high (>2.4V) these switches are
also loaded with a nominal 400mA current.
Provided test points enable the evaluation of voltage loss
across the PPTC (TP9 - TP10) and likewise across the
ISL6118 enabled switches (TP9 - TP6 and TP7). Expect to
see 100% - 300% greater voltage loss across the PPTC than
the ISL6118 (see Figure 11 for ISL6118 vs PPTC voltage
loss comparison).
An overcurrent (OC) condition can be invoked on both the
ISL6118 and the PPTC by driving TP11 to +6V, causing SW1
to close and a nominal 0.94mA load is imposed. This
represents a current overload to the ISL6118 and is thus
quickly current regulated to the 600mA limit. If the OC
duration extends beyond the nominal 12ms of the internal
ISL6118 timer then the output is latched off and the fault
output is asserted by being pulled low turning on the
appropriate FAULT LED. (Please note: the labeling for the
FAULT-1 and FAULT-2 is reversed.) The eval board is
designed to only invoke a OC condition on channel 2 (TP4)
so that a channel to channel isolation evaluation in the
presence of a OC condition can be evaluated.
The primary function of any OC protection device is to
quickly isolate the voltage bus from a faulty load. Unlike the
PPTC and other vendor available IC products, the ISL6118
internal timer that starts upon OC detection provides
consistent protection that is independent of temperature.
Figures 11 through 13 illustrate the comparative efficiency
and effectiveness of the ISL6118 vs the PPTC in protecting
and isolating a faulty load capable from drooping the system
bus in that system.
FIGURE 11. ISL6118 vs PPTC INTO 8.2
LOAD
FIGURE 12. ISL6118 vs PPTC INTO 3.5
LOAD
FIGURE 13. ISL6118 vs PPTC WITH EXTENDED 3.5
LOAD
Typical Performance Curves
(Continued)
VOLTAGE (0.5V/DIV)
V
3.32V
ISL6118
V
OUT
3.29V (0.075
)
0.4A HOLD
CURRENT PPTC
2.93V (1.1
)
GND
VOLTAGE (0.5V/DIV)
TIME (4ms/DIV)
VIN
ISL6118 CR
12ms PERIOD
0.4A HOLD CURRENT PPTC OUT
ISL6118 OUT
VOLTAGE (0.5V/DIV)
TIME (4s/DIV)
ISL6118 OUT
0.4A HOLD CURRENT PPTC OUT
VIN
2.3V AT 10s
1.5V AT 30s
ISL6118
相关PDF资料 |
PDF描述 |
|---|---|
| ISL6AHPEVAL1-T | Dual Power Supply Controller |
| ISL6118HIB | Dual Power Supply Controller |
| ISL6118HIB-T | Dual Power Supply Controller |
| ISL6118HIBZA | Dual Power Supply Controller |
| ISL6118HIBZA-T | Dual Power Supply Controller |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL6E | 制造商:Carlo Gavazzi 功能描述: |
| ISL70001ASEH | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Rad Hard and SEE Hard 6A Synchronous Buck Regulator |
| ISL70001ASEHEV1Z | 制造商:Intersil Corporation 功能描述:ISL70001ASEHEV1Z EVAL BOARD 1 - ROHS COMPLIANT - 48LD C - Bulk |
| ISL70001ASEHF | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Rad Hard and SEE Hard 6A Synchronous Buck Regulator |
| ISL70001ASEHF/PROTO | 制造商:Intersil Corporation 功能描述:RADIATION HARDENED SYNCHRONOUS BUCK REGULATOR, PROTO, FP - Trays |
发布紧急采购，3分钟左右您将得到回复。